• 아동학회지
• /
• 제31권6호
• /
• pp.1-13
• /
• 2010

This study examined the time-dependent effects of changes in private education on the trajectories of academic achievement among early adolescents. Five-wave data was employed from the KYPS; the participants being 2844 (1524 boys, 1320 girls). All were 4th graders in 2004 and became 8th graders in 2008. Latent growth curve model indicated that academic achievement significantly decreased over the five time points, but there were significant individual differences as well. Participants who reported higher initial levels of academic achievement tended to decrease in academic achievement more slowly over time compared to participants who reported lower levels of initial academic achievement. The effects of private education on academic achievement were at their most powerful when participants were in the 4th grade. Private educational experiences among 6th graders had relatively less influence upon the academic achievement of 7th graders.

• 한국재난정보학회 논문집
• /
• 제12권1호
• /
• pp.69-73
• /
• 2016

선점법에 대한 연구가 유한요소법처럼 범용화 되어 있지 않아 적용성과 유효성에 대한 연구가 필요하다. 본 연구에서는 범용적으로 사용된 유한요소법과 비교하여 비선형 진동문제에 대한 선점법의 적용성과 유효성을 확인한다. 또한, 선점법을 미분방정식 조건에 따라 내부법, 경계법, 혼합법으로 나누어 비선형 응답 곡선을 유한요소법 결과와 비교하여 동적 특성 문제의 선점법 적용성과 유효성을 확인한다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.877-882
• /
• 2005

Dynamic stability of an axially accelerating beam stucture is investigated in this paper. The equations of motion of a fixed-free beam are derived using the hybrid deformation variable method and the assumed mode method. Unstable regions due to periodical acceleration are obtained by using the Floquet's theory. Stability diagrams are presented to illustrate the influence of the dimensionless acceleration, amplitude, and frequency. Also, buckling occurs when the acceleration exceeds a certain value. It is found that relatively targe unstable regions exist around the first bending natural frequency, twice the first bending natural frequency, and twice the second bending natural frequency. The validity of the stability diagram is confirmed by direct numerical integration of the equations of motion.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1145-1150
• /
• 2005

The aim of this paper is to investigate the effect of surface texturing on metal surface and to understand the potential of friction reduction through micro-scale dimple to fabricate by photolithography on pin-on-disk test using flat-on-flat contact geometry. It was verify that the friction property with respect to the same pitch has been influence on the size of dimple under lubricated sliding contact. Also, we can recognize from Stribeck curve that the friction property has a connection with the size of dimple. It can explain a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. The friction property has been an effect on the size of surface texture on reduction friction, not only because the density of dimple, but also because the ratio of diameter/pitch. This ratio of approximately 0.5 is recommend under the tested friction condition. It suggested that the ratio of d/p is an important parameter for surface texture design.

• 한국정밀공학회지
• /
• 제24권1호
• /
• pp.93-100
• /
• 2007

In this study, an investigation was made on bristles for the prosthetic and periodontally involved patients based on the previous studies. The purpose of this study was to investigate the ideal location and dimensions of bristles for the patients who were installed with fixed prostheses and severely involved periodontitis. 3D scanner was used to develop 3D visual models of bristles and teeth. These models were developed to be used for designing the ideal bristles for the prosthetic and periodontally involved patients. For the ideal design of bristle, interproximal area of dental arch and bristle must get into maximum and standard teeth may have to be chosen from many gypsum molds. During the design process the factors should be considered that influence the removal of plaque by bristle.

• 소성∙가공
• /
• 제21권3호
• /
• pp.151-159
• /
• 2012

Finite element simulations were conducted to investigate the influence of grain growth in the superplastic blow forming process. A microstructure-based constitutive model considering grain growth effects is proposed and used in the simulations. Also, a grain growth rate equation accounting for both static and dynamic grain growth is implemented. The simulations were made using a 2D plane-strain model for constrained blow forming and an axisymmetric model for free bulging. These two models showed different features during the forming stages. However, the forming pressure-time curve and the thickness distribution obtained by both simulations explained well the deformation hardening induced by the grain growth during superplastic forming. This study shows that grain growth is an important factor in determining the material behavior during superplastic deformation.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.217-222
• /
• 2004

The aim of this paper is to investigate the effect of micro-dimple size on reduction friction and to understand the potential of friction reduction through micro-scale dimple to fabricate by photolithography on pin-on-disk test using flat-on-flat contact geometry. It was verify that the friction property with respect to the same pitch has been influence on the size of dimple under lubricated sliding contact. Also, we can recognize from Stribeck curve that the friction property has a connection with the size of dimple. It can explain a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. The friction property has been an effect on the size of surface texture on reduction friction, not only because the density of dimple, but also because the ratio of diameter/pitch. This ratio of approximately 0.5 is recommend under the tested friction condition. It suggested that the ratio of d/p is an important parameter for surface texture design.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1994년도 가을 학술발표회 논문집
• /
• pp.285-290
• /
• 1994

The influence of elevated temperatures on the mechanical properties of concrete is important for fire-resistance studies and also for understanding the behavior of containment vessel, such as nuclear reactor pressure vessels, during service and ultimate condition. The present study is to clarify the damage/deterioration of concrete structures that are subjected to high temperature exposure. To this end, comprehensive experiments are conducted. The major test variables are the peak temperatures, rate of temperature increase, and sustained duration at peak temperature. The results include weight loss residual compressive strength and stress-strain curve. From those results, residua compressive strength formula and stress-strain relationship are proposed.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1994년도 가을 학술발표회 논문집
• /
• pp.291-300
• /
• 1994

The influence of elevated temperatures on the mechanical properties of concrete is important for fire-resistance studies and also for understanding the behavior of containment vessel, such as nuclear reactor pressure vessels, during service and ultimate condition. The present study is to clarify the damage/deterioration of concrete structures that are subjected to high temperature exposure. To this end, comprehensive experiments are conducted. The major test variables are the peak temperatures, rate of temperature increase, and sustained duration at peak temperature. The results include weight loss residual compressive strength and stress-strain curve. From those results, residua compressive strength formula and stress-strain relationship are proposed.

• 한국안전학회지
• /
• 제9권3호
• /
• pp.22-27
• /
• 1994

For the $\beta$=1 specimen with constant thickness, Crack growth rate is smoothly increasing in the a-N curve. On the other hand for $\beta$=2 specimen with various thickness, the inflection point is observed in crack growth rate near the thickness interface. da/dN before the inflection point is increased, and da/dN after the point is decreased, compared to the $\beta$=1 specimen. da/dN near the thickness interface is approached zero. The descending point was observed earlier as $\beta$ increased. Considering the relation between da/dN and λ, the crack propagation rates for the case of $\beta$ =1 incrased almost linearly, however, the crack propagation rates for $\beta$=2,3 decreased more rapidly near the thickness interface. Additionally, the decreased point in da/dN for $\beta$=3 is farther from the thickness interface than the case for $\beta$ =2.