• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.88-89
• /
• 2013

A variety of influenza A viruses from animal hosts are continuously prevalent throughout the world which cause human epidemics resulting millions of human infections and enormous industrial and economic damages. Thus, early diagnosis of such pathogen is of paramount importance for biomedical examination and public healthcare screening. To approach this issue, here we propose a fully integrated Rotary genetic analysis system, called Rotary Genetic Analyzer, for on-site detection of influenza A viruses with high speed. The Rotary Genetic Analyzer is made up of four parts including a disposable microchip, a servo motor for precise and high rate spinning of the chip, thermal blocks for temperature control, and a miniaturized optical fluorescence detector as shown Fig. 1. A thermal block made from duralumin is integrated with a film heater at the bottom and a resistance temperature detector (RTD) in the middle. For the efficient performance of RT-PCR, three thermal blocks are placed on the Rotary stage and the temperature of each block is corresponded to the thermal cycling, namely $95^{\circ}C$ (denature), $58^{\circ}C$ (annealing), and $72^{\circ}C$ (extension). Rotary RT-PCR was performed to amplify the target gene which was monitored by an optical fluorescent detector above the extension block. A disposable microdevice (10 cm diameter) consists of a solid-phase extraction based sample pretreatment unit, bead chamber, and 4 ${\mu}L$ of the PCR chamber as shown Fig. 2. The microchip is fabricated using a patterned polycarbonate (PC) sheet with 1 mm thickness and a PC film with 130 ${\mu}m$ thickness, which layers are thermally bonded at $138^{\circ}C$ using acetone vapour. Silicatreated microglass beads with 150~212 ${\mu}L$ diameter are introduced into the sample pretreatment chambers and held in place by weir structure for construction of solid-phase extraction system. Fig. 3 shows strobed images of sequential loading of three samples. Three samples were loaded into the reservoir simultaneously (Fig. 3A), then the influenza A H3N2 viral RNA sample was loaded at 5000 RPM for 10 sec (Fig. 3B). Washing buffer was followed at 5000 RPM for 5 min (Fig. 3C), and angular frequency was decreased to 100 RPM for siphon priming of PCR cocktail to the channel as shown in Figure 3D. Finally the PCR cocktail was loaded to the bead chamber at 2000 RPM for 10 sec, and then RPM was increased up to 5000 RPM for 1 min to obtain the as much as PCR cocktail containing the RNA template (Fig. 3E). In this system, the wastes from RNA samples and washing buffer were transported to the waste chamber, which is fully filled to the chamber with precise optimization. Then, the PCR cocktail was able to transport to the PCR chamber. Fig. 3F shows the final image of the sample pretreatment. PCR cocktail containing RNA template is successfully isolated from waste. To detect the influenza A H3N2 virus, the purified RNA with PCR cocktail in the PCR chamber was amplified by using performed the RNA capture on the proposed microdevice. The fluorescence images were described in Figure 4A at the 0, 40 cycles. The fluorescence signal (40 cycle) was drastically increased confirming the influenza A H3N2 virus. The real-time profiles were successfully obtained using the optical fluorescence detector as shown in Figure 4B. The Rotary PCR and off-chip PCR were compared with same amount of influenza A H3N2 virus. The Ct value of Rotary PCR was smaller than the off-chip PCR without contamination. The whole process of the sample pretreatment and RT-PCR could be accomplished in 30 min on the fully integrated Rotary Genetic Analyzer system. We have demonstrated a fully integrated and portable Rotary Genetic Analyzer for detection of the gene expression of influenza A virus, which has 'Sample-in-answer-out' capability including sample pretreatment, rotary amplification, and optical detection. Target gene amplification was real-time monitored using the integrated Rotary Genetic Analyzer system.

• The Journal of Industrial Distribution & Business
• /
• v.3 no.1
• /
• pp.7-16
• /
• 2012

Despite the enforcement of SSM control laws such as 'the Law of Developing the Distribution Industry (LDDI)' and 'the Law of Promoting Mutual Cooperation between Large and Small/medium Enterprises (LPMC)' stipulating the business adjustment system, the number of super-supermarkets (SSMs) has ever been expanding in Korea. In France, however, Super Centers are being regulated most strongly and directly in the whole Europe viewing that there is not a single SSM in Paris, which is emphasized to be the outcome from French government's regulation exerted on the opening of large scale retail stores. In France, the authority to approve store opening is deeply centralized and the store opening regulation is a socio-economic regulation driven by economic laws whereas EU strongly regulates the distribution industry. To control the French distribution industry, such seven laws and regulations as Commission départementale d'urbanisme commercial guidelines (CDLIC) (1969), the Royer Law (1973), the Doubin Law (1990), the Sapin Law (1993), the Raffarin Law (1996), solidarite et renouvellement urbains (SRU) (2000), and Loi de modernisation de l'économie (LME) (2009) have been promulgated one by one since the amendment of the Fontanet guidelines, through which commercial adjustment laws and regulations have been complemented and reinforced while regulatory measures have been taken. Even in the course of forming such strong regulatory laws, InterMarche, the largest supermarket chain in France, has been in existence as a global enterprise specialized in retail distribution with over 4,000 stores in Europe. InterMarche's business can be divided largely into two segments of food and non-food. As a supermarket chain, InterMarche's food segment has 2,300 stores in Europe and as a hard-discounter store chain in France, Netto has 420 stores. Restaumarch is a chain of traditional family restaurants and the steak house restaurant chain of Poivre Rouge has 4 restaurants currently. In addition, there are others like Ecomarche which is a supermarket chain for small and medium cities. In the non-food segment, the DIY and gardening chain of Bricomarche has a total of 620 stores in Europe. And the car-related chain of Roady has a total of 158 stores in Europe. There is the clothing chain of Veti as well. In view of InterMarche's management strategies, since its distribution strategy is to sell goods at cheap prices, buying goods cheap only is not enough. In other words, in order to sell goods cheap, it is all important to buy goods cheap, manage them cheap, systemize them cheap, and transport them cheap. In quality assurance, InterMarche has guaranteed the purchase safety for consumers by providing its own private brand products. InterMarche has 90 private brands of its own, thus being the retailer with the largest number of distributor brands in France. In view of its IT service strategy, InterMarche is utilizing a high performance IT system so as to obtainas much of the market information as possible and also to find out the best locations for opening stores. In its global expansion strategy of international alliance, InterMarche has established the ALDIS group together with the distribution enterprises of both Spain and Germany in order to expand its food purchase, whereas in the non-food segment, it has established the ARENA group in alliance with 11 international distribution enterprises. Such strategies of InterMarche have been intended to find out the consumer needs for both price and quality of goods and to secure the purchase and supply networks which are closely localized. It is necessary to cope promptly with the constantly changing circumstances through being unified with relevant regions and by providing diversified customer services as well. In view of the InterMarche's positive policy for promoting local partnerships as well as the assistance for enhancing the local economic structure, implications are existing for those retail distributors of our country.

• The Journal of Society for e-Business Studies
• /
• v.22 no.2
• /
• pp.137-152
• /
• 2017

The decline in the price of IT devices and the development of the Internet have created a new field called Internet of Things (IoT). IoT, which creates new services by connecting all the objects that are in everyday life to the Internet, is pioneering new forms of business that have not been seen before in combination with Big Data. The prospect of IoT can be said to be unlimited in its utilization. In addition, studies of standardization organizations for smooth connection of these IoT devices are also active. However, there is a part of this study that we overlook. In order to control IoT equipment or acquire information, it is necessary to separately develop interworking issues (IP address, Wi-Fi, Bluetooth, NFC, etc.) and related application software or apps. In order to solve these problems, existing research methods have been conducted on augmented reality using GPS or markers. However, there is a disadvantage in that a separate marker is required and the marker is recognized only in the vicinity. In addition, in the case of a study using a GPS address using a 2D-based camera, it was difficult to implement an active interface because the distance to the target device could not be recognized. In this study, we use 3D Depth recognition camera to be installed on smartphone and calculate the space coordinates automatically by linking the distance measurement and the sensor information of the mobile phone without a separate marker. Coordination inquiry finds equipment of IoT and enables information acquisition and control of corresponding IoT equipment. Therefore, from the user's point of view, it is possible to reduce the burden on the problem of interworking of the IoT equipment and the installation of the app. Furthermore, if this technology is used in the field of public services and smart glasses, it will reduce duplication of investment in software development and increase in public services.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.34 no.7
• /
• pp.959-967
• /
• 2005

Lead is a ubiquitous environmental and industrial pollutant that causes a major health concerns. It is known to induce a broad range of physiological, biochemical, and behavioral dysfunctions in laboratory and humans, including hematopoietic system, kidneys, liver, and reproductive system. This study was conducted to investigate the effect of Saengshik supplementation on the lead-induced toxicity in rats. Five week old male Sprague­Dawley rats were randomly assigned to five groups for six weeks as followings: control group (CT), lead acetate treated group (PT), and lead acetate groups administered with three different dosages of Saengshik $(SI2.5-12.5\%,\;S25-25\%,\;and\;S50-50\%).$ Lead acetate (12 mg/rat) was intragastrically administered daily for 6 weeks. The results were summarized as follows; Weight gain and food efficiency ratio were significantly lower (p<0.05) in lead administered group compared with those of the control group. Also, significant lead-induced alteration in blood hemoglobin (HGB), hematocrit (HCT), mean corpuscular volume (MCV), mean corpuscular hemoglobin (MCH), and reticulocyte distribution width (RDW) were observed. In the liver of lead-exposed animals, there was an increase in the lipid peroxidation (MDA) and the level of glutathione (GSH), but superoxiede dismutase (SOD) activity did not change. Lead-exposed animals with $25\%\;and\;50\%$ Saengshik supplementation showed marked improvements in the values of MCH, MCV, and RDW. Also, the level of HCT was significantly increased by $50\%$ Saengshik supplementation. The levels of liver MDA in $12.5\%\;and\;50\%$ Saengshik administered groups and GSH level in $50\%$ Saengshik administered group were significantly decreased compared to the lead administered group. Also, hepatic SOD activity tended to increase in the presence of Saengshik supplementation. Furthermore, the accumulation of lead in liver and kidney was reduced by presence of Saneghshik supplementation. Liver lead concentration was significantly reduced by both $25\%\;and\;50\%$ Saengshik supplementations and kidney lead concentration was significantly reduced by the $25\%$ Saengshik supplementation. These results show that Saengshik may have a protective effect against lead intoxication but the mechanism of their effects remains unclear.

• Journal of Bio-Environment Control
• /
• v.31 no.4
• /
• pp.401-408
• /
• 2022

As research on a controlled environment system based on crop growth environment sensing for sustainable production of horticultural crops and its industrial use has been important, research on how to properly utilize soil moisture sensors for outdoor cultivation is being actively conducted. This experiment was conducted to suggest the proper method of utilizing the TEROS 12, an FDR (frequency domain reflectometry) sensor, which is frequently used in industry and research fields, for each orchard soil in three regions in Korea. We collected soils from each orchard where fruit trees were grown, investigated the soil characteristics and soil water retention curve, and compared TEROS 12 sensor calibration equations to correlate the sensor output to the corresponding soil volumetric water content through linear and cubic regressions for each soil sample. The estimated value from the calibration equation provided by the manufacturer was also compared. The soil collected from all three orchards showed different soil characteristics and volumetric water content values by each soil water retention level across the soil samples. In addition, the cubic calibration equation for TEROS 12 sensor showed the highest coefficient of determination higher than 0.95, and the lowest RMSE for all soil samples. When estimating volumetric water contents from TEROS 12 sensor output using the calibration equation provided by the manufacturer, their calculated volumetric water contents were lower than the actual volumetric water contents, with the difference up to 0.09-0.17 m³·m^-3 depending on the soil samples, indicating an appropriate calibration for each soil should be preceded before FDR sensor utilization. Also, there was a difference in the range of soil volumetric water content corresponding to the soil water retention levels across the soil samples, suggesting that the soil water retention information should be required to properly interpret the volumetric water content value of the soil. Moreover, soil with a high content of sand had a relatively narrow range of volumetric water contents for irrigation, thus reducing the accuracy of an FDR sensor measurement. In conclusion, analyzing soil water retention characteristics of the target soil and the soil-specific calibration would be necessary to properly quantify the soil water status and determine their adequate irrigation point using an FDR sensor.

• Journal of Navigation and Port Research
• /
• v.46 no.1
• /
• pp.1-10
• /
• 2022

This study aims to investigate changes in the demand for ship officers in response to changes in the shipping industry environment in which Maritime Autonomous Surface Ships (MASS) emerge according to the application of the fourth industrial revolution technology to ships, and it looks into changes in the skill of ship officer. It also analyzes and proposes a plan for nurturing ship officers accordingly. As a result of the degree of recognition and AHP analysis, this study suggests that a new training system is required because the current training and education system may cover the job competencies of emergency response, caution and danger navigation, general sailing, cargo handling, seaworthiness maintenance, emergency response, and ship maintenance and management, but tasks such as remote control, monitoring diagnosis, device management capability, and big data analysis require competency for unmanned and shore-based control. By evaluating the importance of change factors in the duties of ship officers in Maritime Autonomous Surface Ships, this study provides information on ship officer educational institutions' response strategies for nurturing ship officers and prioritization of resource allocation, etc. The importance of these factors was compared and evaluated to suggest changes in the duties of ship officers and methods of nurturing ship officers according to the introduction of Maritime Autonomous Surface Ships. It is expected that the findings of this study will be meaningful as it systematically derives the duties and competency factors of ship officers of Maritime Autonomous Surface Ships from a practical point of view and analyzed the perception level of each relevant expert to diagnose expert-level responses to the introduction of Maritime Autonomous Surface Ships.

• International Journal of Ocean System Engineering
• /
• v.2 no.3
• /
• pp.185-194
• /
• 2012

A Macroscopic combination of two or more distinct materials is commonly referred to as a "Composite Material", having been designed mechanically and chemically superior in function and characteristic than its individual constituent materials. Composite materials are used not only for aerospace and military, but also heavily used in boat/ship building and general composite industries which we are seeing increasingly more. Regardless of the various applications for composite materials, the industry is still limited and requires better fabrication technology and methodology in order to expand and grow. An example of this is that the majority of fabrication facilities nearby still use an antiquated wet lay-up process where fabrication still requires manual hand labor in a 3D environment impeding productivity of composite product design advancement. As an expert in the advanced composites field, I have developed fabrication skills with the use of machinery based on my past composite experience. In autumn 2011, the Korea government confirmed to fund my project. It is the development of a composite sanding machine. I began development of this semi-robotic prototype beginning in 2009. It has possibilities of replacing or augmenting the exhaustive and difficult jobs performed by human hands, such as sanding, grinding, blasting, and polishing in most often, very awkward conditions, and is also will boost productivity, improve surface quality, cut abrasive costs, eliminate vibration injuries, and protect workers from exposure to dust and airborne contamination. Ease of control and operation of the equipment in or outside of the sanding room is a key benefit to end-users. It will prove to be much more economical than normal robotics and minimize errors that commonly occur in factories. The key components and their technologies are a 360 degree rotational shoulder and a wrist that is controlled under PLC controller and joystick manual mode. Development on both of the key modules is complete and are now operational. The Korean government fund boosted my development and I expect to complete full scale development no later than 3rd quarter 2012. Even with the advantages of composite materials, there is still the need to repair or to maintain composite products with a higher level of technology. I have learned many composite repair skills on composite airframe since many composite fabrication skills including repair, requires training for non aerospace applications. The wind energy market is now requiring much larger blades in order to generate more electrical energy for wind farms. One single blade is commonly 50 meters or longer now. When a wind blade becomes damaged from external forces, on-site repair is required on the columns even under strong wind and freezing temperature conditions. In order to correctly obtain polymerization, the repair must be performed on the damaged area within a very limited time. The use of pre-impregnated glass fabric and heating silicone pad and a hot bonder acting precise heating control are surely required.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.6
• /
• pp.1173-1178
• /
• 2012

Water competition among domestic, industrial and agricultural sectors has been gradually heightened recently in Korea as the lack of water supply is expected in the near future. About 46% of nation's water use is consumed in paddy farming to produce rice. And the conservation of water resource and quality in agricultural sector is a pending issue in the nation's long term water management plan. New paddy rice farming techniques that use significantly less irrigation water are urgently required. System of Rice Intensification (SRI) that is now well known to produce more rice with less water consumption has not been tried in Korea yet. And environmental effect of SRI on greenhouse gases (GHGs) has not been well investigated. The objective of this study was to measure the effect of SRI on GHGs as well as water use and rice yield in a Korean paddy condition. Three experimental runoff plots $5{\times}15m$ in size were prepared at an existing paddy field. Runoff, GHGs emission and water quality were measured during the 2011 growing seasons while a Japonica rice variety was cultivated. Rice plants grew better and healthier in SRI plots than in continuously flooded (CF) and intermittently drained (ID) plots. Rice yield from SRI plots increased 112.8 (ID)~116.1 (CF)% compared with CF and ID plots. Irrigation requirement of SRI plots compared to CF plot reduced by 52.6% and ID plot reduced by 62.0%, meaning that about 37.9~47.4% of irrigation water could be saved. GHGs emission from SRI plots reduced by 71.8% compared to that from CF plot and by 18.4% compared to that from ID plot, meaning that SRI could help contribute to ease the greenhouse gas accumulation in the atmosphere. It was believed that SRI is a promising paddy farming technique that could increase rice yield, and reduce irrigation water requirement and GHGs emission not just in Korea but also other rice farming countries all over the world. However, it was recommended that long term studies under different conditions including rice variety, soil texture, water source, climate need to be conducted for reliable data for the development of environmental policies related to GHGs emission control and management.

• Journal of Preventive Medicine and Public Health
• /
• v.26 no.2 s.42
• /
• pp.222-230
• /
• 1993

Industrial glues, known as 'Bonds' in Korea, contain many kinds of organic solvents, and glue sniffing of youths became one of the social problems in Korea. Mixed exposures to solvents by glue sniffing may induce chronic toxicities different from those by exposures to solvents of single component. To test effects of the glue sniffing on weight gain or central nervous system, two groups of 20 male Sprague-Dawley rats were exposed to air(control group) or vapors of the glues to narcotic status(exposed group), and weight check, tail flick test, hot plate test, rotarod treadmill test were done on the 14th,24th, 36th, 45th, 53rd, 86th, 102nd, 117th, 134th and 151st days after the first exposure. On the 188th day, their brains were excised and examined by a pathologist. Weight gain, controlled against time change, showed significant difference between the groups, but response times in tail flick test, hot plate tests, and rotarod treadmill test didn't. In pathological examination with blind method, no macroscopic or microscopic differences were found between the two groups. These results suggests that organic lesion in central nervous system may not ensue glue sniffing, but, before firm conclusion, more studies in various exposure conditions should be followed.

• Food Science and Industry
• /
• v.55 no.2
• /
• pp.188-202
• /
• 2022

In the insect industry, as the scope of application of insects is expanded from pet insects and natural enemies to feed, edible and medicinal insects, the demand for quality control of insect raw materials is increasing, and interest in securing the safety of insect products is increasing. In the process of expanding the industrial scale, controlling the temperature and humidity and air quality in the insect breeding room and preventing the spread of pathogens and other pollutants are important success factors. It requires a controlled environment under the operating system. European commercial insect breeding facilities have attracted considerable investor interest, and insect companies are building large-scale production facilities, which became possible after the EU approved the use of insect protein as feedstock for fish farming in July 2017. Other fields, such as food and medicine, have also accelerated the application of cutting-edge technology. In the future, the global insect industry will purchase eggs or small larvae from suppliers and a system that focuses on the larval fattening, i.e., production raw material, until the insects mature, and a system that handles the entire production process from egg laying, harvesting, and initial pre-treatment of larvae., increasingly subdivided into large-scale production systems that cover all stages of insect larvae production and further processing steps such as milling, fat removal and protein or fat fractionation. In Korea, research and development of insect smart factory farms using artificial intelligence and ICT is accelerating, so insects can be used as carbon-free materials in secondary industries such as natural plastics or natural molding materials as well as existing feed and food. A Korean-style customized breeding system for shortening the breeding period or enhancing functionality is expected to be developed soon.