• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.230-233
• /
• 2005

This paper present a new method for world wide network motor controlled system. It use disturbance observer to present high precision position control algorithm to disturbance change, and to apply this to induction motors. It shows that proposed algorithm is strong in induction motor precision control for disturbance change. This system with disturbance observer used deadbeat control, which have high benefit, is good for quick disturbance compensation. To show these effectiveness the whole process is simulated by simulink, and also experimented by DSP6416 with TCP-IP network board.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1030-1032
• /
• 2000

Direct torque control algorithm for 3-level inverter-fed induction motors is proposed. Conventional selection method of the stator voltage vector shows problems of stator flux drooping phenomenon and undesirable torque control appeared especially at the low, speed operation. To overcome these problems, a proposed method uses intermediate voltage vectors, which are inherently generated in 3-level inverters. An adaptive observer is also employed to estimate some state-variables and motor parameters, which takes a deep effect on the performance of the low speed operation. Simulation and experiment results verify effectiveness of the proposed algorithm.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.2672-2674
• /
• 2000

In this paper. feedback linearization and the sliding mode control(SMC) are used together for uncertain nonlinear system. An advantage of feedback linearization technique is to make linear control theories can be used for nonlinear system and the SMC have the robustness. But the dynamics of the SMC has the dynamics lower order than that of the original system. Therefore the linear control theory can not be used with the SMC. The novel sliding surface of the SMC can have the dynamics of the nominal non linear system controlled by the feedback linearization. The proposed method can be used for the control of induction motors.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.2
• /
• pp.101-109
• /
• 2005

The newly developed speed sensorless control scheme is proposed to estimate both motor speed and rotor resistance simultaneously using variable rotor flux. The rotor flux is given as sinusoidal waveform with an amplitude and a frequency without affecting precise torque control. Especially the proposed method makes the simultaneous estimation of rotor resistance and speed with high precision even though at the low speed area including a few rpm. Moreover, on-line identification of rotor resistance can be performed simply without calculating troublesome trigonometric functions and complicated integral computation. Therefore, the proposed system can be accomplished by using very cheap microprocessors for several applications. The results of the numerical simulations and experiments demonstrate that this method is effective to estimate the speed and on-line identification of rotor resistance for sensorless induction motors.

• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.308-310
• /
• 1996

Recently, as a result of the progress in power electronics and microelectronics, the inverter technology is quickly developing. Also, by using the fast microprocessor and small-sized switching devices, such as IPM, the Inverter becomes more compact and cheap. This paper proposes an inexpensive and small-sized vector controller for induction motors using 87C196MC and IPM. The proposed inverter contributes further space-saving, and high performance features to motor drives system.

• Journal of Power Electronics
• /
• v.17 no.3
• /
• pp.725-732
• /
• 2017

This paper proposed a real-time, low-cost, fast transistor open-circuit fault diagnosis method for voltage-source inverter fed induction motors. A transistor open-circuit changes the symmetry of the inverter topology, leading to different similarities among three phase load currents. In this paper, dynamic time warping is proposed to describe the similarities among load currents. The proposed diagnosis is independent of the system model and needs no extra sensors or electrical circuits. Both simulation and experimental results show the high efficiency of the proposed fault diagnosis method.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1276-1278
• /
• 2005

In this paper, we propose an adaptive sliding mode observer-based control of induction motors with uncertainties. The proposed adaptive sliding mode flux observer generates estimates both for the unknown parameters(load torque and rotor resistance) and for the unmeasured state variable (rotor fluxes); they converge to the corresponding true value under persistency of excitation which actually holds in typical operating conditions. The proposed controller guarantees speed tracking and bounded signals for every initial condition of the motor. Simulations show that all estimation errors tend quickly to zero so that high tracking performances are achieved both for speed and rotor flux.

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.255-257
• /
• 1995

In this paper, a new speed estimation method of induction motors based on the very quick torque control is proposed to realize speed sensorless control. The proposed method can be realized very simply by detecting primary motor current and voltage command at every sampling time. As the method need not the differential value of primary current in a arithmetic of voltage command, it can be expected to promote the precision of speed estimation in low speed area, especially. Through the numerical simulation, the validity of the proposed method was successfully confirmed.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.848-850
• /
• 2002

Single phase induction motor is directly used usual source, it can be a source of an appliance such as mechanical fan, refrigerator, washing machine, etc. Especially capacitor-run single phase induction motor is suitable to make more inexpensive and high efficient products because it is more high efficiency, and good to start than other single phase induction motors. Generally, voltage and current of capacitor-run single phase induction motor transfer to the part of positive phase and negative phase based on two motor theory. In this paper, we simulate the torque characteristics to capacitance variation from single phase induction motor's equivalent circuit. Through the test using the real motor, we compare and investigate the maximum torque of run state related with capacitance and the adequacy of the converted model.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.428-433
• /
• 2001

This paper presents the control algorithm for maximum efficiency drives of an induction motor system with the high dynamic performance. This system uses a simple model of the induction motor that includes equations of iron losses. The model, which only requires the parameters of induction motor, is referred to a field-oriented frame. The minimum point of the input power can be obtained at the steady state condition. The reference torque and flux currents for the vector control of induction motors are calculated by the optimal efficiency control algorithm. The drive system with the proposed efficiency optimization controller has been implemented by a 32 bit floating point TMS320C32 DSP chip. The results show the effectiveness of the control strategy proposed for the induction motor drive.