• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.16 no.5
• /
• pp.223-229
• /
• 2023

This Paper propose the method that measure main system parameters for PI(proportional-integral) current control of a.c. motor adopting the vector control technique. For current control, the PI control input is could be tuning by several selective methods. Among the several methods, the method that using the main system parameters, wire resistance and inductance, are frequently used. In this study, the technique to dissect and measure these two system parameters through the results of simple feedback control. This analytic measurement method is measuring parameters step by step dissecting the results of P control using simple proportional feedback gain about the unit step or multiple step reference command. This strategy is an real time analytic measurement method that calculate current control gains of torque component and flux component both for vector control of A.C. motor without introducing the further measurement circuits and complex measuring algorithms.

• Progress in Superconductivity
• /
• v.13 no.2
• /
• pp.105-110
• /
• 2011

SQUID sensor-based ultra low-field magnetic resonance apparatus with ${\mu}T$-level measurement field requires a strong prepolarization magnetic field ($B_p$) to magnetize its sample and obtain magnetic resonance signal with a high signal-to-noise ratio. This $B_p$ needs to be ramped down very quickly so that it does not interfere with signal acquisition which must take place before the sample magnetization relaxes off. A MOSFET switch-based $B_p$ coil driver has current ramp-down time ($t_{rd}$) that increases with $B_p$ current, which makes it unsuitable for driving high-field $B_p$ coil made of superconducting material. An energy cycling-type current driver has been developed for such a coil. This driver contains a storage capacitor inside a switch in IGBT-diode bridge configuration, which can manipulate how the capacitor is connected between the $B_p$ coil and its current source. The implemented circuit with 1.2 kV-tolerant devices was capable of driving 32 A current into a thick copper-wire solenoid $B_p$ coil with a 182 mm inner diameter, 0.23 H inductance, and 5.4 mT/A magnetic field-to-current ratio. The measured trd was 7.6 ms with a 160 ${\mu}F$ storage capacitor. trd was dependent only on the inductance of the coil and the capacitance of the driver capacitor. This driver is scalable to significantly higher current of superconducting $B_p$ coils without the $t_{rd}$ becoming unacceptably long with higher $B_p$ current.

• Journal of the Korean Vacuum Society
• /
• v.19 no.1
• /
• pp.72-80
• /
• 2010

It is very important to predict and analyze the change of voltage and current distribution of current strap, abnormal voltage distribution of transmission line and resonance phenomenon by coupling between current straps for more stable operation of ICRF system. In this study, to understand those phenomena by coupling, 8-port coupled transmission line model is completed by appling S-parameter measured in the prototype KSTAR ICRF antenna to the model. The determined self-inductance, mutual-inductance and capacitance of antenna straps are shown to be lower than that calculated from 2D approximate model due to finite length of strap. The coupled transmission line model of current strap will be utilized to the operation of ICRF system of KSTAR in the future.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.4
• /
• pp.49-53
• /
• 1999

In this study, the characteristics of the structure of buried type capacitor for RF multi- chip-module are investigated. We developed many kinds of structures to minimize the space of capacitor in module and the value of parastic series inductance without any loss in capacitance, and in this procedure the effect of vias especially position, size, number length are analyzed and optimized. This characteristics of structures are checked through HFSS(high frequency structure simulator) of HP, and the value of parastic series inductance is calculated by equivalent circuit analysis. And ensuing the result of simulation, we made buried type capacitors using LTCC (low temperature cofired ceramic) material. In measurement of this sample, we found out the effective and precise method can be applied to buried type and characteristics of vias and striplines added for measuring are quantified.

• ETRI Journal
• /
• v.33 no.1
• /
• pp.6-12
• /
• 2011

A case study of an active transmitting patch antenna revealed a characteristic loop locus of DC power versus RF output power as drive frequency was varied, with an operational bandwidth substantially smaller than the impedance bandwidth of the radiator. An approximate simulation technique, based on separation of the output capacitance of the power transistor, yielded easily visualized plots of power dependence on internal load impedance, and a simple interpretation of the experimental results in terms of a near-resonance condition between the output capacitance and output packaging inductance.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.972-975
• /
• 2004

This paper presents a simulation results of sensorless control of Switched Reluctance Motor(SRM) using neural network. The basic algorithm of this scheme is based on the flux linkage characteristic according to the phase current and the rotor position. A sufficient simulation data was used for neural network training. Through measurement of the phase flux linkage and phase currents the neural network is able to estimate the rotor position. The simulation result shows some good results, and possibility of this algorithm.

• Proceedings of the KIEE Conference
• /
• 2000.07a
• /
• pp.271-273
• /
• 2000

A magnetic field generator for small animal study was designed and constructed. For calculation of magnetic fields inside the cage, a three-dimensional calculation program was made. Using this, optimum electric current ratio and position of each coil were determined. Meanwhile, inductance of the generator was calculated for design of power supply. The field measurement results of the manufactured generator showed that the difference between maximum and minimum magnetic field at the living floor was less than 2%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.182-183
• /
• 2006

An electromagnetic memory effect observed in superconducting YBCO system was studied. From the measurement of differential conductance, it was cleared that the mechanism of electromagnetic memory can not be explained by using conventional flux flow model. By changing the density of external magnetic flux, changes m inductance of a coil in which a superconducting bar is inserted were also measured. It was concluded that the electromagnetic memory effect aries from the interaction between the trapped magnetic flux and the weak link of the filament formed in the superconducting bar.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.3 no.1
• /
• pp.42-46
• /
• 2003

In this paper, an MMIC broadband amplifier for wireless communication systems has been developed by using an active feedback method. This active feedback operates at much higher frequencies than a method by a spiral inductor feedback and its size is independent of the inductance value. The MMIC broadband amplifier was designed using a $0.5{\;}{\mutextrm{m}}$ MESFET library. The fabricated chip area was $1.4{\;}mm{\;}{\times}{\;}1.4{\;}mm. Measurement showed a gain of 18 dB with a gain flatness of ${\pm}3$ dB in a 1.5 GHz~3.5 GHz band. The maximum output power and the minimum noise figure were 14 dBm and 2.5 dB in the same band, respectively.

• Proceedings of the Korea Society of Information Technology Applications Conference
• /
• 2002.11a
• /
• pp.363-370
• /
• 2002

A substrate network model characterizing substrate effect of submicron MOS transistors for RF operation and its parameter extraction with physically meaningful values are presented. The proposed substrate network model includes a single resistance and inductance originated from ring-type substrate contacts around active devices. Model parameters are extracted from S-parameter data measured from common-bulk configured MOS transistors with floating gate and use where needed with out any optimization. The proposed modeling technique has been applied to various-sized MOS transistors. Excellent agreement the measurement data and the simulation results using extracted substrate network model up to 30GHz.