• 한국정보통신학회논문지
• /
• 제11권12호
• /
• pp.2343-2351
• /
• 2007

본 논문은 시변 펄스형 자기장(Time-varying Magnetic field)을 반복적으로 발생시키는 전원장치 및 전원장치에서 발생된 에너지를 자기장으로 발생키시기 위한 자기유도 코일 probe의 설계 및 구현을 통하여 짧은 시간($300{\mu}s$이하) 동안 고자기장(${\sim}1.2Tesla$)을 발생시켰다. 시간과 펄스 주기를 순차적으로 조정 할 수 있는 다단 메쉬 방식으로 설계하여 고반복적($0.1Hz{\sim}20Hz$)으로 스위칭했을 경우에도 동일한 출력세기를 발생시킬 수 있는 자기장 의료기기 시스템을 구현하였다.

• Smart Structures and Systems
• /
• 제28권6호
• /
• pp.727-735
• /
• 2021

Recently, non-destructive health monitoring methods such as magnetic flux leakage (MFL) method, have become popular due to their advantages over destructive methods. Currently, numerical study on this field has been limited to simplified studies by only obtaining MFL instead of induced voltage inside coil sensor. In this study, it was proposed to perform a novel numerical simulation of MFL's coil sensor by considering vital parameters including specimen's motion with constant velocity and saturation status of specimen in time domain. A steel-rod specimen with two stepwise cross-sectional changes (i.e., 21% and 16%) was fabricated using low carbon steel. In order to evaluate the results of numerical simulation, an experimental test was also conducted using a magnetic probe, with same size specimen and test parameters, exclusively. According to comparative results of numerical simulation and experimental test, similar signal amplitude and signal pattern were observed. Thus, proposed numerical simulation method can be used as a reliable source to check efficiency of sensor probe when different size specimens with different defects should be inspected.

• Progress in Superconductivity
• /
• 제14권1호
• /
• pp.1-10
• /
• 2012

We fabricated a closed coils by using resistive-joint method and the joint resistance of the coils were estimated by field decay technique in liquid nitrogen. We used the Runge-kutta method for the numerical analysis to calculate the decay properties. The closed coil was wound by $(Bi,Pb)_2Sr_2Ca_2Cu_3O_x$/Ag tape. Both ends the tape were overlapped and soldered to each other. The current was induced in a closed coils by external magnetic flux density. Its decay characteristic was observed by means of measuring the magnetic flux density generated by induced current at the center of the closed coil with hall sensor. The joint resistance was calculated as the ratio of the inductance of the loop to the time constants. The joint resistances were evaluated as a function of critical current of loop, contact length, sweep time, and external magnetic flux density in a contact length of 7 cm. It was observed that joint resistance was dependent on contact length of a closed coil, but independent of critical current, sweep time, and external magnetic flux density. The joint resistance was measured to be higher for a standard four-probe method, compared with that for the field decay technique. This implies that noise of measurement in a standard four-probe method is larger than that of field decay technique. It was estimated that joint resistance was $8.0{\times}10^{-9}{\Omega}$ to $11.4{\times}10^{-9}{\Omega}$ for coils of contact length for 7 cm. It was found that 40Pb/60Sn solder are unsuitable for persistent mode.

• Journal of Magnetics
• /
• 제15권2호
• /
• pp.70-73
• /
• 2010

A magnetic phase is partly produced in a steam generator tube due to stress and heat, because steam generator tubes are exposed to high temperature, high pressure and radioactivity conditions. This adversely affects the safety of steam generator tubes. However, it is difficult to detect it using conventional eddy current methods. Therefore, a new type of probe is needed to separate the signals from the defects and magnetic phases. In this study, a new U-type yoke, which contained two types of coils, a magnetizing coil and detecting coil, was designed. In addition, the signal induced by the magnetic phase and defect in an Inconel 600 plate were simulated.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 제4회 영호남학술대회 논문집
• /
• pp.47-51
• /
• 2002

ECT(eddy currentign testing) is very effective technique to detect a flaw within a conductor. Co-based amorphous wire was used as a sensor head. The wire has almost 0 magneto-striction and high permeability. An uniform magnetic field was applied to 1mm thick copper plate and $25{\mu}m$ thick aluminum sheet conductor using spiral typed coil The size of the coil has $40mm{\times}40mm$ outer width and $8mm{\times}8mm$ inner width. The copper plate and aluminum sheet has 0.5mm and 0.1mm wide gap, respectively. The frequency range of applied field was 100kHz-600kHz. The induced voltage difference of 2.5mV was obtained in the maximum voltage and minimum one measured across the gap of the 1mm thick conductor. In the case of aluminum sheet, 0.4mV was obtained. From this results, the effectiveness of Co-based amorphous wire was confirmed in the ECT technique.

• 비파괴검사학회지
• /
• 제27권5호
• /
• pp.398-408
• /
• 2007

본 논문에서는 반사형 펄스와전류 탐상법을 사용하여 두께를 효과적으로 평가하기 위해 여러가지 탐촉자 모델들을 설계하고, 수치해석 방법을 사용하여 피검사체의 두께 변화에 따른 펄스와전류 신호의 특징 변화, 민감도 등을 조사하였다. 반사형 탐상에서는 센서코일이 여자코일 자계보다는 피검사체에 형성된 와전류로 인한 자계를 감지해야 하므로, 구리-페라이트로 차폐한 모델들과 페라이트만으로 차폐한 모델들에서의 펄스와전류 신호를 조사하였다. 이러한 신호들에서 두께 판별에 유용한 특성을 조사하여 신호의 피크값과 zero crossing time을 선정할 수 있었고, 이들의 두께변화에 대한 민감도를 조사하였다. 그 결과, 두 종류의 차폐 모델들에서 모두 피크값 민감도가 zero crossing time 민감도보다 효과적이라는 것을 알 수 있었고, 구리-페라이트로 차폐한 모델 보다 페라이트만으로 차폐한 모델에서의 피크값 민감도가 훨씬 더 높다는 것을 알 수 있었다.

• 비파괴검사학회지
• /
• 제30권5호
• /
• pp.464-470
• /
• 2010

고온, 고압에서 운용되고 있는 설비의 안전성을 평가하기 위해서는 사용시간 동안 열화된 역학물성을 정기적으로 점검하여야 한다. 비파괴적으로 열화된 설비의 역학적 특성을 점검하기 위하여 표면형 프로브(surface type probe)를 사용한 가역투자율 측정방법이 제시된다. 가역투자율 측정방법은 가역투자율이 자기 이력곡선의 미분값임에 근거하고 있다. 가역투자율은 교류 섭동 자기장의 주파수에 동조된 록-인 증폭기로 측정된 탐지코일에 유도된 전압의 제 1 고조파이다 가역투자율의 첨두값은 보자력 영역에서 나타난다. 실험에 사용된 강재는 12Cr 페라이트 내열강으로 $700^{\circ}C$의 등온에서 열처리 시간을 달리한 11개의 시편을 제작하였다. 가역투자율 첨두값 사이의 간격 (peak interval of reversible permeability: PIRP), 비커스 경도 및 인장강도는 열화가 진행됨에 따라 초기에는 급격하게, 후반에는 완만하게 감소하였다. PIRP가 감소함에 따라 인장강도와 비커스 경도가 선형적으로 감소하였고 이 상관관계를 이용하면 측정한 가역투자율로 12Cr 페라이트 내열강의 열화된 역학적 물성을 비파괴적으로 평가할 수 있다.