• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.166-166
• /
• 2010

Recently, TFTs based on amorphous oxide semiconductors (AOSs) such as ZnO, InZnO, ZnSnO, GaZnO, TiOx, InGaZnO(IGZO), SnGaZnO, etc. have been attracting a grate deal of attention as potential alternatives to existing TFT technology to meet emerging technological demands where Si-based or organic electronics cannot provide a solution. Since, in 2003, Masuda et al. and Nomura et al. have reported on transparent TFTs using ZnO and IGZO as active layers, respectively, much efforts have been devoted to develop oxide TFTs using aforementioned amorphous oxide semiconductors as their active layers. In this thesis, I report on the performance of thin-film transistors using amorphous indium gallium zinc oxides for an active channel layer at room temperature. $SiO_2$ was employed as the gate dielectric oxide. The amorphous indium gallium zinc oxides were deposited by RF magnetron sputtering. The carrier concentration of amorphous indium gallium zinc oxide was controlled by oxygen pressure in the sputtering ambient. Devices are realized that display a threshold voltage of 1.5V and an on/off ration of > $10^9$ operated as an n-type enhancement mode with saturation mobility with $9.06\;cm^2/V{\cdot}s$. The devices show optical transmittance above 80% in the visible range. In conclusion, the fabrication and characterization of thin-film transistors using amorphous indium gallium zinc oxides for an active channel layer were reported. The operation of the devices was an n-type enhancement mode with good saturation characteristics.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.170-170
• /
• 2010

Thin-film transistors (TFT) have become the key components of electronic and optoelectronic devices. Most conventional thin-film field-effect transistors in display applications use an amorphous or polycrystal Si:H layer as the channel. This silicon layers are opaque in the visible range and severely restrict the amount of light detected by the observer due to its bandgap energy smaller than the visible light. Therefore, Si:H TFT devices reduce the efficiency of light transmittance and brightness. One method to increase the efficiency is to use the transparent oxides for the channel, electrode, and gate insulator. The development of transparent oxides for the components of thin-film field-effect transistors and the room-temperature fabrication with low voltage operations of the devices can offer the flexibility in designing the devices and contribute to the progress of next generation display technologies based on transparent displays and flexible displays. In this thesis, I report on the dc performance of transparent thin-film transistors using amorphous indium tin zinc oxides for an active layer. $SiO_2$ was employed as the gate dielectric oxide. The amorphous indium tin zinc oxides were deposited by RF magnetron sputtering. The carrier concentration of amorphous indium tin zinc oxides was controlled by oxygen pressure in the sputtering ambient. Devices are realized that display a threshold voltage of 4.17V and an on/off ration of ${\sim}10^9$ operated as an n-type enhancement mode with saturation mobility with $15.8\;cm^2/Vs$. In conclusion, the fabrication and characterization of thin-film transistors using amorphous indium tin zinc oxides for an active layer were reported. The devices were fabricated at room temperature by RF magnetron sputtering. The operation of the devices was an n-type enhancement mode with good saturation characteristics.

• Journal of the Semiconductor & Display Technology
• /
• v.6 no.1 s.18
• /
• pp.65-69
• /
• 2007

A design of experiments was applied in order to investigate the effect of processing variables in UV irradiation on the electrical/optical properties in indium-zinc oxide thin films, The processing variables, equivalently input variables are listed as UV irradiation time, oxygen flow rate, and chamber pressure. The statistical significance of Ultra Violet (UV) treatment was confirmed using a paired-t test. The full factorial $2^3$ design was employed to determine significant main and interaction effects in UV irradiation process. The chamber pressure and the interaction between UV irradiation time and $O_2$ flow rate were found to be statistically significant at the significance level of 0.1. Furthermore, the optimized approach was proposed in achieving the improved conductivity after UV irradiation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.159-159
• /
• 2008

투명전도체 (transparent conducting oxides: TCOs) 는 일반적으로 $10^3\Omega^{-1}Cm^{-1}$의 전도도, 가시광 영역에서 80%이상의 투명성을 가지는 재료로서, 액정 박막 표시 장치(TFT-LCD), 광기전성 소자, 유기 발광 소자, 에너지 절약 창문, 태양전지(sollar cell) 등 전극으로 사용되고 있다. 최근에는 TCO의 전도도특성을 조절하여 반도성특성을 가진 투명 산화물 반도체(transparent oxide semiconductor: TOS) 을 이용한 박막 트랜지스터 연구가 활발히 진행 중이다. 기존의 실리콘을 기반으로 하는 박막 트랜지스터의 낮은 이동도, 불투명성의 특성을 가지고 있지만, 산화물 박막트랜지스터는 높은 이동도를 발현 할 수 있을 뿐만 아니라, 넓은 밴드갭 에너지를 갖는 산화물을 이용하므로 투명한 특성도 발현 할 수 있어 차세대 디스플레이의 구동소자로서 응용연구가 되고 있다. 이에 본 연구에서는 박막트랜지스터 channel layer로서의 Indium-Tin-Zinc oxide 적용특성을 조사하였다. Indium, Tin, Zinc 의 혼합비율을 다양하게 조절하여 타겟을 제작하였다. 이를 RF magnetron sputtering 를 이용하여 박막으로 성장시켰으며, 기판으로는 glass 기판을 사용하였다. 박막 성장시 아르곤과 산소의 비율을 다양하게 조절하였다. 성장시킨 박막은 Hall effect, Transmittance, Work function, XRD등을 이용하여 전기적, 광학적, 구조특성을 평가하였다. Indium-Tin-Zinc Oxide(ITZO) 을 channel layer로 사용하여 Thin-film transistor 을 제작하여, TFT의 I-V 및 stability특성을 평가하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.187-187
• /
• 2012

Solution-processed metal-alloy oxides such as indium zinc oxide (IZO), indium gallium zinc oxide (IGZO) has been extensively researched due to their high electron mobility, environmental stability, optical transparency, and solution-processibility. In spite of their excellent material properties, however, there remains a challenging problem for utilizing IZO or IGZO in electronic devices: the supply shortage of indium (In). The cost of indium is high, what is more, indium is becoming more expensive and scarce and thus strategically important. Therefore, developing an alternative route to improve carrier mobility of solution-processable ZnO is critical and essential. Here, we introduce a simple route to achieve high-performance and low-temperature solution-processed ZnO thin film transistors (TFTs) by employing alkali-metal doping such as Li, Na, K or Rb. Li-doped ZnO TFTs exhibited excellent device performance with a field-effect mobility of $7.3cm^2{\cdot}V-1{\cdot}s-1$ and an on/off current ratio of more than 107. Also, in case of higher drain voltage operation (VD=60V), the field effect mobility increased up to $11.45cm^2{\cdot}V-1{\cdot}s-1$. These all alkali metal doped ZnO TFTs were fabricated at maximum process temperature as low as $300^{\circ}C$. Moreover, low-voltage operating ZnO TFTs was fabricated with the ion gel gate dielectrics. The ultra high capacitance of the ion gel gate dielectrics allowed high on-current operation at low voltage. These devices also showed excellent operational stability.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.168-168
• /
• 2010

Transparent conduction oxides (TCOs) films is extensively reported for optoelectronic devices application such as touch panels, solar cells, liquid crystal displays (LCDs), and organic light emitting diodes(OLEDs). Among the many TCO film, indium tin oxide(ITO) is in great demand due to the growth of flat panel display industry. However, indium is not only high cost but also its deposits dwindling. Therefore, many studies are being done on the transparent conductive oxides(TCOs). We fabricated a target of IZTO(In2O3:ZnO:SnO2=70:15:15 wt.%) reduced indium. Then, IZTO thin films were deposited on glass substrates by pulsed DC magnetron sputtering with various oxygen flow ratio. The substrate temperature was fixed at the room temperature. We investigated the electrical, optical, structural properties of IZTO thin films. The electrical properties of IZTO thin films were dependent on the oxygen partial pressure. As a result, the most excellent properties of IZTO thin films were obtained at the 3% of oxygen flow rate with the low resistivity of $7.236{\times}10^{-4}{\Omega}cm$. And also the optical properties of IZTO thin films were shown the good transmittance over 80%. These IZTO thin films were used to fabricated organic light emitting diodes(OLEDs) as anode and the device performances studied. The OLED with an IZTO anode deposited at optimized deposition condition showed good brightness properties. Therefore, IZTO has utility value of TCO electrode although it reduced indium and we expect it is possible for the IZTO to apply to flexible display due to the low processing temperature.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.324-324
• /
• 2012

투명전도체(Transparent Conducting Oxides: TCOs)는 일반적으로 면저항이 $103{\Omega}/sq$ 이하로 전기가 잘 통하며, 가시광선영역인 380~780 nm에서의 투과율이 80% 이상이고, 3.2eV 이상의 밴드갭을 가지는 재료로써, 전기전도도와 가시광선영역에서 투과성이 높아 전기적, 광학적 재료로 관심을 받아 다년간 연구대상이 되어오고 있다. 현재 가장 널리 사용되고 있는 투명전도체(Transparent Conducting Oxides: TCOs) 소재로는 Indium Tin Oxide (ITO)가 가장 각광받고 있지만, Indium의 가격상승과 박막의 열처리를 통해 저항이 증가하는 단점을 가지고 있어 이를 대체 할 새로운 소재 개발이 필요한 상황이다. 그러므로 투명전도체 소재 개발에 있어서 가장 중요한 연구과제는 Indium Tin Oxide(ITO)의 단점을 개선시키고 안정된 고농도의 In-Zn-Sn-O(ITZO) 박막을 성장시키는 것이다. 본 연구에서는 RF스퍼터링법에 의하여 Si wafer에 In-Zn-Sn-O(IZTO)를 $350{\AA}$ 만큼 증착시키고, 1시간 동안 $300^{\circ}C$, $350^{\circ}C$, $400^{\circ}C$로 각각 열처리 하였다. 박막의 전자적, 광학적 특성은 XPS(X-ray Photoelectron Spectroscopy), REELS(Reflection Electron Energy Loss Spectroscopy)를 이용하여 연구하였다. XPS측정결과, ITZO박막은 In-O, Sn-O and Zn-O의 결합을 가지고 있고, 박막의 열처리를 통해 $400^{\circ}C$에서 Zn2p의 피크가 가장 크게 나타나는 반면 In3d와 Sn3d는 열처리를 했을 때가 Room Temperature에서 보다 피크가 작아지는 것을 확인하였다. 이는 $400^{\circ}C$에서 Zn가 표면에 편석됨을 나타낸다. 그리고 REELS를 이용해 Ep=1500 eV에서의 밴드갭을 얻어보면, 밴드갭은 $3.25{\pm}0.05eV$로 온도에 크게 변화하지 않았다. 또한 QUEELS -Simulation에 의한 광학적 특성 분석 결과, 가시광선영역인 380nm~780nm에서의 투과율이 83%이상으로 투명전자소자로의 응용이 가능하다는 것을 보여주었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.101-101
• /
• 2011

투명전도성산화물(transparent conducting oxides, TCOs) 박막으로써 널리 쓰이는 산화인듐주석(indium tin oxide, ITO)은 전기 전도성과 광 투과성이 우수하여 주로 유기발광다이오드(organic light-emitting diode, OLED)의 전극, 발광다이오드(light-emitting diode, LED)의 current spreading 층 및 태양전지(solar cell)의 윈도우층(window layer) 등의 광전자 소자로 응용되고 있으나, 고가의 indium 가격과 인체에 유해한 독성 등이 문제점으로 지적되고 있다. 따라서 indium의 함량을 저감한 새로운 조성의 TCO 또는 indium을 함유하지 않은 친환경적인 TCO 대체 재료 개발의 필요성이 증대되고 있다. 이러한 재료 중 하나인 AZO (Al-doped zinc oxide, $Al_2O_3$: 2 wt.%)는 3.82eV의 넓은 에너지 밴드갭을 가지며, 가시광선 및 근 적외선 파장 영역에 대하여 90% 이상의 높은 투과율을 나타낸다. 또한, 습식식각이 가능하며, 매우 풍부하여 원가가 매우 저렴하고, 독성이 없다. 본 연구에서는 박막 증착율이 높고, 제작과정의 조정이 용이한 RF magnetron 스퍼터를 이용하여 glass 기판 위에 AZO 박막을 성장하고, $N_2$ 분위기에서 다양한 온도 조건에서 열처리(rapid thermal annealing, RTA)하여 전기 및 광학적 특성에 대하여 비교 분석하였다. 또한, 이후에 기존의 성장방법과 달리 고가의 진공 장비를 사용하지 않고, 저온에서도 간단한 구조의 장비를 이용하여 균일한 나노구조를 성장시킬 수 있는 전기화학증착법(electrochemical deposition)으로 AZO 박막위에 ZnO 나노로드를 다양한 성장조건에 따라 성장시켜 광학적 특성을 비교 분석하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.108-108
• /
• 2009

ITO에 사용되는 주된 재료인 인듐의 bixbyite 구조는 TCOs의 전기적 특성에서 매우 중요한 것으로 알려져 있다. 때문에 인듐의 Bixbyite구조를 유지하면서 인듐의 사용량을 줄이기 위해 최적의 Solubility limit에 관해 연구하였다. 이를 위해 In2O3-ZnO-SnO2의 삼성분계 기본 조성에 두가지 물질을 추가로 첨가하여 첨가량에 따른 Solubility limit을 연구하였다. Solubility limit의 측정을 위해 X-ray Diffractometer(XRD)를 사용하였으며, 첨가 원소의 양이 증가할수록 TCOs target의 Latice parameter값은 작아졌다, SEM을 통한 미세구조의 관찰로 원소첨가에 따른 샘플의 소결에너지 변화를 분석할 수 있었다. 제작된 시편의 정성분석 및 Chemical binding Energy를 측정하기 위해 X-ray Photo Spectroscopy (XPS)를 이용하였으며, 전기적인 특성 측정을위해 4-Point prove mesurement 방법을 사용하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.207.2-207.2
• /
• 2013

Oxide-based thin film transistors have been attempted as powerful candidates for driving circuits for active-matrix organic light-emitting diodes and transparent electronics. The oxide TFTs are based on the amorphous multi-component oxides involving zinc, indium, and/or tin elements as main cation sources. The current work employed RF sputtering in order to deposit zinc-tin oxide thin films applicable to transparent oxide thin film transistors. The deposited thin film was characterized and probed in terms of materials and devices. The physical/chemical characterizations were performed using X-ray diffraction, Atomic Force Microscopy, Spectroscopic Ellipsometry, and X-ray Photoelectron Spectroscopy. The thin film transistors were fabricated using a bottom-gated structure where thermally-grown silicon oxide layers were applied as gate-dielectric materials. The inherent properties of oxide thin films are combined with the corresponding device performances with the aim to fabricating the multi-component oxide thin films being optimized towards transparent electronics.