• 한국터널지하공간학회 논문집
• /
• 제20권3호
• /
• pp.543-560
• /
• 2018

도심지 지하공간의 개발과 운행선 하부를 저토피로 입체 교차화하는 시설 증가에 따라 비개착식 공법의 수요는 점차 증가추세에 있으나 대다수의 공법은 중대구경 강관을 압입하여 루프를 형성하고 내부를 굴착하는 파이프루프(Pipe roof) 계열의 공법이 주로 적용되고 있다. 강관 압입 시 발생되는 이완영역 및 하중은 여러 인자의 영향을 받게 되나 가장 큰 요소는 압입하는 강관의 크기에 좌우되며 이는 강관 루프 내 지중구조물에 작용하는 하중의 크기로 볼 수 있다. 지반의 교란 및 이완하중 발생을 최소화시키기 위해 개발된 SEM공법(Super Equilibrium Method)은 기존의 중대구경 강관 대신 ${\Phi}114mm$ 내외의 소구경 강관을 사용한다. 이 소구경 강관을 SEM파일로 명명하였으며 강관의 선 압입 및 그라우팅 보강을 실시한 후 지반의 침하나 융기 없이 지반 내 횡단구조물을 유압잭을 이용하여 압입하게 된다. 이와 같이 SEM공법의 구성 중 지보역할을 하는 SEM파일은 선단부 굴착 시 지반의 붕락을 방지하고 상재하중을 지지하기 위한 길이 5 m 내외의 Fore poling 파일이며 이 파일의 배치간격, 시공연장, 부재의 강성 등을 산정하기 위해서는 이완영역의 적절한 산정이 필수적이다. 본 논문은 SEM공법의 최적설계를 위하여 SEM파일 압입 시 발생되는 이완하중 산정 값을 비교분석하였다. 이완영역 산정에 근거한 주요 이론식 및 경험식들의 영향인자를 고려하여 분석하고 FEM analysis (유한요소 해석)를 수행하여 SEM파일에 적합한 이완하중 산정을 검토하였다. 또한 실제 SEM파일 압입 및 굴착 시 발생되는 지반이완을 확인하기 위해 강관압입 축소모형실험을 수행하였으며 토피고/강관(H/D)에 따른 지표침하 및 지반이완을 정량적으로 검토하였다.

• 대한치과보철학회지
• /
• 제43권3호
• /
• pp.293-305
• /
• 2005

Statement of problems. Conventional feldspathic porcelain is used extensively as a restorative material and it is subjected to grinding and polishing during fabrication and delivery procedures. There is still considerable controversy concerning the best methods to achieve the strongest porcelain restorations after such adjustments. Purpose. The objective of this study was to investigate the effects of (1) overglazing, (2) selfglazing, and (3) fine polishing on the flexural strength and fracture toughness of feldspathic dental porcelain. Material and method. Ninety porcelain disks were prepared for flexural strength test and sixty porcelain disks were fabricated for fracture toughness test. Specimens were divided into three groups for each test as follows: 1) overglazed 2) self-glazed 3) polished. The flexural strength of feldspathic porcelains was determined by ring-on-ring biaxial flexural strength test. The fracture toughness values of three experimental groups were obtained by indentation fracture toughness test. Results. The flexural strength of overglazed group was significantly higher than that of selfglazed and polished group (P<0.05), while the difference between self-glazed and polished group was not significant (P>0.05). The fracture toughness values of overglazed and polished group were significantly higher than that of self-glazed group (P<0.05), while the difference between overglazed and polished group was not significant (P>0.05). Conclusions. This results supported the use of polishing as an alternative to glazing metal ceramic restorations, as it was not detrimental in flexural strength and fracture toughness. But, under the conditions of this study, overglazing was the ideal surface finishing method of feldspathic dental porcelain.

• 한국해양공학회지
• /
• 제25권6호
• /
• pp.66-71
• /
• 2011

Recently, the production of shipbuilding and offshore plant industries, with a trend toward large structures, has led to an increased use of high strength ultra-thick plates. The use of ultra-thick plates increases the welding tasks, and the welding process generates distortion and residual stress in the weldment because of the rapid heating and cooling. Welding distortion and residual stress in the welded structure resulte in many troubles such as deformation and life deterioration. In particular, the welding residual stress has an important effect on welding deformation, fatigue, buckling strength, brittleness, etc. The purpose of this study was to evaluate the residual stress at a multi-pass weldment using an experimental method for EH36 high-tension steel. In this experimental method, AIS3000 was used to measure the residual stress of a welded part, HAZ, and base metal; EPMA and XRD were used to study the material properties.

• 한국분말재료학회지
• /
• 제23권5호
• /
• pp.384-390
• /
• 2016

Tri-isotropic (TRISO) coatings on zirconia surrogate beads are deposited using a fluidized-bed vapor deposition (FB-CVD) method. The silicon carbide layer is particularly important among the coated layers because it acts as a miniature pressure vessel and a diffusion barrier to gaseous and metallic fission products in the TRISO-coated particles. In this study, we obtain a nearly stoichiometric composition in the SiC layer coated at $1400^{\circ}C$, $1500^{\circ}C$, and $1400^{\circ}C$ with 20 vol.% methyltrichlorosilane (MTS), However, the composition of the SiC layer coated at $1300-1350^{\circ}C$ shows a difference from the stoichiometric ratio (1:1). The density decreases remarkably with decreasing SiC deposition temperature because of the nanosized pores. The high density of the SiC layer (${\geq}3.19g/cm^2$) easily obtained at $1500^{\circ}C$ and $1400^{\circ}C$ with 20 vol.% MTS did not change at an annealing temperature of $1900^{\circ}C$, simulating the reactor operating temperature. The evaluation of the mechanical properties is limited because of the inaccurate values of hardness and Young's modulus measured by the nano-indentation method.

• Corrosion Science and Technology
• /
• 제17권3호
• /
• pp.101-108
• /
• 2018

AA7010 is an Al-Zn-Mg-Cu alloy containing Zr, developed as an alternate to traditional AA7075 alloy owing to their high strength combined with better fracture toughness. It is necessary to improve the corrosion resistance and surface properties of the alloy by incorporating plasma electrolytic oxidation (PEO) method. AA7010-T7452 aluminum alloy has been processed through the forging route with multi-stage working operations, and was coated with $10{\mu}m$ thick $Al_2O_3$ ceramic aluminina coating using the plasma electrolytic oxidation (PEO) method. The corrosion, stress corrosion cracking (SCC) and nano-mechanical behaviours were examined by means of potentiodynamic polarization, slow strain rate test (SSRT) and nano-indentation tests. The results indicated that the additional thermomechanical treatment during the forging process caused a fully recrystallized microstructure, which lead to the poor environmental cracking resistance of the alloy in 3.5% NaCl solution, despite the overaging treatment. Although the fabricated PEO coating improved general corrosion resistance, the brittle nature of the coating did not provide any improvement in SCC resistance of the alloy. However, the hardness and elastic modulus of the coating were significantly higher than the base alloy.

• 치위생과학회지
• /
• 제18권1호
• /
• pp.42-49
• /
• 2018

The computer-aided design/computer-aided manufacturing (CAD/CAM) system was introduced to shorten the production time of all-ceramic restorations and the number of patient visits. Among these types of ceramic for dental CAD/CAM, they have been processed into inlay, onlay, and crown shapes using leucite-reinforced glass-ceramics to improve strength. The purpose of this study was to observe the mechanical properties and microstructure of leucite-reinforced glass-ceramics for dental CAD/CAM. Two types of leucite-reinforced glass-ceramic blocks (IPS Empress CAD, Rosetta BM) were prepared with diameter of 13 mm and thickness of 1 mm. Biaxial flexural testing was conducted using a piston-on-three-ball method at a crosshead speed of 0.5 mm/min. Weibull statistics were used for the analysis of biaxial flexural strength. Fracture toughness was obtained using an indentation fracture method. Specimens were observed by field emission scanning electron microscopy to examine the microstructure of the leucite crystalline phase after acid etching with 0.5% hydrofluoric acid aqueous solution for 1 minute. The results of strength testing showed that IPS Empress CAD had a mean value of $158.1{\pm}8.6MPa$ and Rosetta BM of $172.3{\pm}8.3MPa$. The fracture toughness results showed that IPS Empress CAD had a mean value of $1.28{\pm}0.19MPa{\cdot}m^{1/2}$ and Rosetta BM of $1.38{\pm}0.12MPa{\cdot}m^{1/2}$. The Rosetta BM sample exhibited higher strength and fracture toughness. Moreover, the crystalline phase size and ratio were increased in the Rosetta BM sample. The above results are expected to elucidate the basic mechanical properties and crystal structure characteristics of IPS Empress CAD and Rosetta BM. Additionally, they will help develop leucite-reinforced glass-ceramic materials for CAD/CAM.

• 한국항공우주학회지
• /
• 제31권10호
• /
• pp.73-78
• /
• 2003

항공우주 분야의 MEMS 기술의 중요성은 경량화 및 높은 분해능 등의 목적아래 점차 증가하고 있는 추세이다. 따라서 MEMS 기기의 제작에 있어 박막 물성의 조사 및 개선 방안은 중요한 논점이 되고 있으며, 박막의 잔류응력은 MEMS 기기 제작 및 구동에 있어 해결해야 할 중요한 문제점으로 남았있다. 따라서 본 논문에서는 MEMS 기기의 구조제로 많이 쓰이는 LPCVD 다결정 실리콘에 He+, Ar+ 이온을 주입함으로써 응력 구배를 완화하였다. 또한 Nano-indenter를 이용한 CSM 방법을 사용하여, 다결정 실리콘의 탄성계수와 경도를 압입 깊이에 따라 측정하였다. 그 결과, 이온 주입에 의한 결정성의 변화가 탄성계수와 경도를 감소시키지만, 이온 농도가 증가함에 따라 탄성계수와 경도가 증가하는 현상을 관찰하였다.

• The Journal of Advanced Prosthodontics
• /
• 제8권6호
• /
• pp.479-488
• /
• 2016

PURPOSE. The aim of this study was to test the modulus of elasticity (E) across the interfaces of yttria stabilized zirconia (YTZP) / veneer multilayers using nanoindentation. MATERIALS AND METHODS. YTZP core material (KaVo-Everest, Germany) specimens were either coated with a liner (IPS e.max ZirLiner, Ivoclar-Vivadent) (Type-1) or left as-sintered (Type-2) and subsequently veneered with a pressable glass-ceramic (IPS e.max ZirPress, Ivoclar-Vivadent). A $5{\mu}m$ (nominal tip diameter) spherical indenter was used with a UMIS CSIRO 2000 (ASI, Canberra, Australia) nanoindenter system to test E across the exposed and polished interfaces of both specimen types. The multiple point load - partial unload method was used for E determination. All materials used were characterized using Scanning Electron Microscopy (SEM) and X - ray powder diffraction (XRD). E mappings of the areas tested were produced from the nanoindentation data. RESULTS. A significantly (P<.05) lower E value between Type-1 and Type-2 specimens at a distance of $40{\mu}m$ in the veneer material was associated with the liner. XRD and SEM characterization of the zirconia sample showed a fine grained bulk tetragonal phase. IPS e-max ZirPress and IPS e-max ZirLiner materials were characterized as amorphous. CONCLUSION. The liner between the YTZP core and the heat pressed veneer may act as a weak link in this dental multilayer due to its significantly (P<.05) lower E. The present study has shown nanoindentation using spherical indentation and the multiple point load - partial unload method to be reliable predictors of E and useful evaluation tools for layered dental ceramic interfaces.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권8호
• /
• pp.348-353
• /
• 2003

This paper was the research of high voltage suspension insulator (400 [kN]) including pottery stone, feldspar, clay and alumina of 17 [wt%]. The slurry was fabricated after ball milling mixed raw materials. Green compacts were made by the extrusion of jiggering method and were sintered at 1300[$^{\circ}C$] for 50 [min.] in the tunnel kiln. The sintered density was reached to 97% of theoretical density, and the bending strength was 1658 [k $g_{f}$/$\textrm{cm}^2$] and hardness and fracture toughness which was measured by ICL( indentation crack length ) method were 1658 (kgf/$\textrm{cm}^2$) and 27.5 [Gpa], respectively. In measurement of tana and insulation break voltage of 400 (kN) porcelain, tan$\delta$ took some numerical value between 17${\times}$10$_{-3}$ and 61${\times}$10$_{-3}$ and insulation break voltage value was 19.9$\pm$1.4 [㎸/mm]. The test was performed to research whether the shape of pin affect a overvoltage break load or not As a consequence, when a pin was designed a pin diameter 51 [mm] with the bottom form of two-step constructed with straight in the suspension insulator, Insulator showed overvoltage break load 52 [ton] of the highest value and reflected a fine characteristic in aged deterioration test which is one of the accelerated aging test. Also it could be confirmed a fine characteristic through performing the test that electrical property of insulator was established correctly in accordance with IEC 60383-1 standards.s.

• 한국세라믹학회지
• /
• 제36권1호
• /
• pp.61-68
• /
• 1999

층상구조를 이루는 재료의 소결시 형성되는 다양한 결함 및 잔류응력을 고찰하기 위해 TZP-SUS계 및 ZT/SUS계다층재료와 porcelain/alumina 및 porcelain/Y-TZP 이층재료를 소결법으로 제조하였다. 상압소결로 제조한 다층재료에서는 층간의 소결수축율 차이에 의해 warping, splitting, 균열 등의 소결결함이 관찰되었으며, 중간층수 및 두께의 조절과 출발물질의 제어를 통해 이러한 소결결함이 완화됨을 알 수 있었다. Tape casting법으로 제조한 다층재료에서는 소결시 가한 압력에 의해 소결결함, 특히 warping이 제어됨을 확인할 수 있었다. 이층재료에서 형성되는 잔류응력은 vickers 압입법으로 관찰하였다. Porcelain/alumina에서는 porcelain 측의 계면에 작은 인장응력이, porcelain/Y-TZP에서는 압축응력이 형성됨을 확인할 수 있었으며, 이러한 잔류응력은 이층재료의 강도에도 영향을 미침을 알수 있었다. 결국 다층재료의 소결결함 및 잔류응력은 재료설계와 출발물질 상수에 영향을 받는다는 것을 알 수 있었다.