• Asian-Australasian Journal of Animal Sciences
• /
• v.21 no.1
• /
• pp.51-58
• /
• 2008

Four ruminally cannulated Nili-ravi buffalo bulls were used in a $4{\times}4$ Latin Square design to determine the influence of varying levels of ruminally degradable protein (RDP) on ruminal characteristics, digestibility, blood pH, blood urea nitrogen (BUN) and nitrogen (N) balance. Four isonitrogenous and isocaloric diets were formulated (NRC, 2001). The control diet contained 50% RDP. The medium (MRDP), high (HRDP) and very high (VHRDP) ruminally degradable protein diets had 66, 82 and 100% RDP, respectively. Increasing the level of dietary RDP resulted in a linear decrease in ruminal pH. A quadratic effect of RDP on ruminal pH was also observed with quadratic maxima at the 66% RDP diet. Dietary RDP had a quadratic effect on total bacterial and protozoal count with maximum microbial count at the 82% RDP diet. Increased microbial count was due to increasing level of ruminal ammonia nitrogen ($NH_3-N$). Increasing dietary RDP resulted in a linear increase in dry matter digestibility. Provision of an adequate amount of RDP caused optimum microbial activity, which resulted in improvement in DM digestibility. Increasing the level of dietary RDP resulted in a linear decrease in crude protein (CP) and neutral detergent fiber digestibility. Blood pH remained unaltered across all diets. A linear increase in ruminal $NH_3-N$ and BUN was noted with increasing level of dietary RDP. The increase in BUN was due to increased ruminal $NH_3-N$ concentrations. A positive N balance was noted across all diets. The results are interpreted to suggest that buffalo bulls can utilize up to 82% RDP of total CP (16%) with optimum results.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.4
• /
• pp.1409-1413
• /
• 2015

Background: According to increase in elderly populations, and change in lifestyle and cancer-causing behavior, the global burden of cancer is increasing. For prevention and control of disease, knowledge of population statistics of cancers and their trends is essential. This study aimed to investigate the epidemiology and trends of cancer in the province of Kerman: southeast of Iran. Materials and Methods: This analytical and cross-sectional study was carried out based on cancer registry data at the Disease Management Center of the Health Ministry from 2004 to 2009 in the province of Kerman in Iran. Common cancers were defined as the number of reported cases and standardized incidence rates. To compute the annual percentage change (APC), joinpoint 4.1.1.1 software was applied. Results: Of 10,595 registered cases, 45.3% (4802 cases) were in women and 56.7% (5,793 cases) occurred in men. The standardized incidence rates for both females and males were increasing during the six years studied. The most common cancers in both sexes during six years of studied were skin (13.4%), breast (9.35%), bladder (7.8%), stomach (7.45%), leukemia (7.05%), colorectal(5.57%), lung(4.92%), trachea(3.51%) and prostate(2.48%). Conclusions: Our findings revealed that the cancer incidence is demonstrating increasing trends in both sexes in the province of Kerman. This may be because of changes in lifestyle, increasing exposure to risk factors for cancer and increase of life expectancy. If this is the case, increasing public awareness of cancer risk factors is a high priority, together with introduction of large-scale screening techniques.

• Journal of Korea Foundry Society
• /
• v.17 no.1
• /
• pp.58-66
• /
• 1997

The main aim of the present study is to investigate the effects of several processing parameters on the characteristics of Fe-Al alloy preform manufactured by reactive sintering process. The processing parameters include preform composition of 25, 40, 50, 60 and 75at.%Al, compacting pressure of 10, 20 and $30kg/cm^2$, and mean Al particle size of 29, 66 and $187{\mu}m$. Mean Fe particle size was $39{\mu}m$. The density of preform processed under same compacting pressure was not affected by changing Al composition. The preform with Al compositions of 25, 40, 50 and 60at.% Al swelled after reactive sintering process, thus having lower density than the green compacts. The preform with Al compositions of 75at.%Al, however, shrinked after reactive sintering process, thus having higher density than the green compacts. Ignition temperature increased with increasing compacting pressure, and increased with increasing Al composition at the fixed compacting pressure. And adiabatic temperature decreased with increasing compacting pressure at the fixed Al composition, and increased with increasing Al composition at the fixed compacting pressure. The size of compound particles increased with increasing Al composition. Especially, The size of compound particles increased largely in the case of 75at.%Al. It was observed that 50at.%Al preform have three dimentional network structure having a homogeneous and fine decreasing Al particle size.

• Asian-Australasian Journal of Animal Sciences
• /
• v.19 no.2
• /
• pp.176-180
• /
• 2006

This study was carried out to establish clipping interval of Pennisetum orientale (PO) and Panicum antidotale (PA) to get maximum biomass production with optimal nutritional value for Nili buffaloes. Two clipping intervals i.e. $CI_1$, and $CI_2$ (clipped after every one and two months, respectively) were studied for both grasses. The data on various parameters were compared with PO and PA each clipped at 4 months of age (control). Leaf to stem ratio in both PO and PA declined with increasing clipping interval. Concentration of dry matter (DM) and organic matter (OM) increased (p<0.05) whereas crude protein contents decreased with increasing clipping interval in both grasses. Crude protein and dry herbage yields in PO and PA increased (p<0.05) with increasing clipping interval. The DM and neutral detergent fiber (NDF) digestibilities of PO and PA in ruminally cannulated buffalo bulls decreased (p<0.05) due to more lignification with increasing clipping interval. Ruminal extent of digestion, rate of disappearance of DM and neutral detergent fiber of PO and PA decreased in buffaloes while ruminal lag time of these nutrients increased significantly (p<0.05) with increasing clipping interval. The results from the study imply that two month clipping interval for both PO and PA grasses favored higher biomass with greater nutritional value for Nili buffaloes and sustained grass vigor.

• Textile Coloration and Finishing
• /
• v.22 no.3
• /
• pp.187-193
• /
• 2010

The effects of molecular weight (MW) and concentration on the rheological properties of poly(vinyl alcohol) (PVA) solutions in dimethyl sulfoxide (DMSO) were investigated at $30^{\circ}C$. Ubbelohde viscometer and rotational rheometer were employed for dilute and concentrated regime, respectively. In the dilute regime, the Mark-Houwink exponent ($\alpha$) of the solutions determined from three different MWs proved 0.73. The critical concentration (C*), in which the entanglement and overlap of polymer molecules began to take place, decreased with increasing the MW of PVA. Huggins constant ($K_H$) values ranged from 0.33 to 0.45 over the MW examined. In the log-log plot of $\eta_{sp}$ versus [$\eta$]C, the PVA with higher degree of polymerization (DP) gave a greater slope exhibiting the inflection point in the vicinity of C*. In the dynamic viscosity ($\eta'$) curve, the PVA solutions of DP 1700 presented Newtonian fluid behavior over most of the frequency range examined. However, the lower Newtonian flow region reduced with increasing the DP. As the PVA concentration increased, $\eta'$ was increased and the onset shear rate for pseudoplasticity was decreased. In the Cole-Cole plot, PVA solutions showed almost a single master curve in a slope of ca. 1.65 regardless of the DP. However, the increase of the concentration from 8 to 12 wt% for PVA solutions of DP 5000 decreased the slope from 1.73 to 1.57. In the tan $\delta$ curve, the onset frequency for sol-gel transition was shifted from 154 to 92 rad/s with increasing the DP from 3300 to 5000 and from 192 to 46 rad/s with increasing the concentration from 8 to 12 wt%. In addition, longer relaxation time ($\lambda$) was observed with increasing the DP and concentration.

• The Journal of Korean Physical Therapy
• /
• v.21 no.4
• /
• pp.57-63
• /
• 2009

Purpose: To better understand falls in elderly women, we measured differences in muscle activities of 4 lower extremity muscles (tibialis anterior, soleus, rectus femoris, biceps femoris) based on angle plantar-flexion in elderly women. Methods: Subjects were 15 healthy elderly women. No subjects had musculoskeletal or nervous disorders. EMGs were used to check muscle activity of lower extremity muscles. For statistic analysis, data were expressed as a percentage of maximal voluntary isometric contraction (%MVIC). We measured %MVIC for 5 sec under 4 conditions and did not use data for the first and last second. Muscle activities of the muscles of the lower extremities were measured based on the degree of plantar-flexion of the ankle joint. The 4 conditions corresponded to different degrees of: 0, 10, 20 and 30 degrees. This was done using a 50 cm board for measuring the degrees. Results: The tibialis anterior, soleus, and bicpes femoris showed increasing muscle activity associated with increasing degree of plantar-flexion of the ankle joint. All muscles showed a significant increase in muscle activities in association with increasing degrees. Rectus femoris showed a significant increase in muscle activity for 0 degrees and for the other degrees, but there were no further changes when plantar flexion of the ankle joint was over 10 degrees. Conclusion: Activities of the muscles of the lower extremities except rectus femoris were higher with increasing degree of plantar flexion. High muscle activity may result in muscle fatigue. Thus, increasing degree of plantar flexion may be risk factors of falls in elderly women.

• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.2
• /
• pp.109-120
• /
• 1997

Microstructure and mechanical properties of Fe-Si-Mn-P high strength steel sheet have been investigated by controlling the cooling rate. Bainite and ferrite were obtatined by annealing in the ferrite pluse austenite region, and ferrite and austenite were obtatined after annealing in the fully austenite region. Ferrite and pearlite were obtained when the cooling rate was controlled from the annealing temperature above $760^{\circ}C$ and bainite showed with increasing cooling rate, however below $760^{\circ}C$ ferrite and bainite were obtained. Tensile strengths and hardness nearly unchanged with increasing cooling rate after control the cooling rate from the temperature above $760^{\circ}C$, while tensile strengths increased and elongation decreased with increasing cooling rate when the cooling rate was controlled from the tempeature below $760^{\circ}C$. Without regard to annealing temperature, tensile strength increased and elongation decreased with increasing cooling rate. Tensile strengths and elongation values heat treated in the ferrite plus austenite region were higher than those in the fully austenite region. Retained austenite and strength-elongation balance showed the maximum value at $780^{\circ}C$ and decreased with increasing annealing temperature. Strength-elongation balance value was controlled by the retained austenite.

• Journal of the Korean Society for Heat Treatment
• /
• v.7 no.1
• /
• pp.25-34
• /
• 1994

To investigate the effect of austenitizing tempratures on the mechanical properties and corrosion resistance of 0.19%C-13.6%Cr martensitic stainless steel, the changes in martensitic trasformation temperatures, mechanical properties and anodic polarization curve were examined after changing the austenitizing temperatures and tempering temperatures. On increasing heating rate at the same austenitizing temperatures, $A_s$, $A_r$ and $M_s$ increased. And the $M_s$ temperature showed to be decreased with increasing austenitizing temperature. With increasing tempering temperature up to $500^{\circ}C$, strength, hardness and impact value were not changed remarkably, on the other hand the tensile strength and hardness decreased and impact value increased after tempering above $550^{\circ}C$ owing to the $M_{23}C_6$ carbide precipitation. The abrupt decrease in elongation at the tempering temperture of $500^{\circ}C$ proved to the precipitation of $M_7C_3$ carbide. The effect of austenitizing temperature on the mechanical properties of the tempered specimen showed to be decreased in impact value and elongation at the austenitizing temperature of $1150^{\circ}C$. At low tempering temperatures the corrosion resistance of the tempered specimen was not changed obviously with increasing tempering temperature. On the other hand, the resistance decreased above the tempering temperature of $600^{\circ}C$ due to the precipitation of $M_{23}C_6$ carbides. The corrosion resistance showed to be improved with increasing the austenitizing temperature owing to the dissolution of carbides.

• Korean Journal of Materials Research
• /
• v.5 no.8
• /
• pp.1040-1044
• /
• 1995

Magnetic garnet films of (YSmLuCa)$_3$(FeGe)$\_$5/O$\_$12/ have been grown by the liquid phase eqitaxy method on the substrate of non-magnetic garnet Gd$_3$Ga$\_$5/O$\_$12/. The variation of Sm ion concentration were varied 0.3, 0.4, 0.6, mole/formula unit respectively. The magnetic properties of the samples for the bubble magnetic materials, such as, line width ΔH of ferromagnetic resonance (FMR), magnetic saturation induction 4$\pi$Ms, wall mobility u$\_$w/ uniaxial magnetic anisotropy energy Ku, were measured and discussed the relations between these properties. The line width ΔH decreases with increasing 4$\pi$Ms, and with decreasing Sm concentration. The anisotropy energy Ku increases not only with increasing Sm ion concentration, but also increasing 4$\pi$Ms. The value of wall mobility u$\_$w/ increase with increasing 4$\pi$Ms and decreases with increasing Sm concentration. We define a physical constant Eι from the fact that the product of 4$\pi$Ms and ΔH is constant with dimension of energy density. The Eι is dependent only on Sm concentration.density. The Eι is dependent only on Sm concentration.

• Korean Journal of Environmental Agriculture
• /
• v.30 no.2
• /
• pp.99-104
• /
• 2011

BACKGROUND: Application of urea may increase $CO_2$ emission from soils due both to $CO_2$ generation from urea hydrolysis and fertilizer-induced decomposition of soil organic carbon (SOC). The objective of this study was to investigate the effects of increasing urea application on $CO_2$ emission from soil and mineralization kinetics of indigenous SOC. METHODS AND RESULTS: Emission of $CO_2$ from a soil amended with four different rates (0, 175, 350, and 700 mg N/kg soil) of urea was investigated in a laboratory incubation experiment for 110 days. Cumulative $CO_2$ emission ($C_{cum}$) was linearly increased with urea application rate due primarily to the contribution of urea-C through hydrolysis to total $CO_2$ emission. First-order kinetics parameters ($C_0$, mineralizable SOC pool size; k, mineralization rate) became greater with increasing urea application rate; $C_0$ increased from 665.1 to 780.3 mg C/kg and k from 0.024 to 0.069 $day^{-1}$, determinately showing fertilizer-induced SOC mineralization. The relationship of $C_0$ (non-linear) and k (linear) with urea-N application rate revealed different responses of $C_0$ and k to increasing rate of fertilizer N. CONCLUSION(s): The relationship of mineralizable SOC pool size and mineralization rate with urea-N application rate suggested that increasing N fertilization may accelerate decomposition of readily decomposable SOC; however, it may not always stimulate decomposition of non-readily decomposable SOC that is protected from microbial decomposition.