• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.11
• /
• pp.498-502
• /
• 2005

The objectives of this paper are to provide information on the characteristics of the discharge signals in a low-voltage indoor outlet. Most of electrical fires are caused by short circuits, overheating of wires, deterioration and incomplete connection of wiring devices. The last two cases are predictable before the occurrence of fire because of its slow progress. We have simulated the discharge signals caused by the deterioration and incomplete connection of wiring devices using aged outlets. From the experimental data, we could characterize the frequency spectrums of the discharge signals depending on the cases. The higher frequency components of the signal are attenuated by the capacitance and inductance of power lines as the measuring point is getting away from the discharges. Main frequency components of the discharge signal are existent at 600kHz - 1.5MHz in incomplete connections and at 210H7z - 8MHz in deteriorations of the outlet.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.2
• /
• pp.200-203
• /
• 2005

Most of electrical fires are caused by short circuits, overheating of wires, deterioration and incomplete connection of wiring devices. The last two cases are predictable before the occurrence of fire because of its slow progress. In this paper, we have simulated the discharge signals caused by the deterioration and incomplete connection of wiring devices using an aged concent to provide information on the characteristics of discharge signals. From the experimental data, we could characterize the frequency spectrums of the discharge signals depending on the cases. The higher frequency components of the signal are attenuated by the capacitance and inductance of power lines as the measuring point is getting away from the discharges. Main frequency components of the discharge signal are existent at 600 kHz - 1.5 MHz in incomplete connections and at 210 kHz - 8 Mhz in deteriorations of the concent.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.302-303
• /
• 2018

This study analyzed the major revision factors and revision contents for 'Construction-Standard-Production-Rate for Construction Works in 2018. Part 16. Pipe Laying Down and Connection" which was revised by the construction expense estimation standard's middle and long-term plans. The main reasons for the revision was analyzed to be unclear construction scope, limitations in applicable pipe material based on the facility type, labor force mainly composed of ordinary workers, limitations of labor force, and incomplete appropriation standard for the tool rent fee and equipment expenses. Through revision of factors, common items were newly established, organization was revised, the labor force was mainly composed of the technicians, and basis for appropriation of equipment expenses was arranged. In addition, through periodic revision, the appropriation standard for bend and special pipes was set. Consequently, more practical construction cost estimate standard is arranged through revision.

• Journal of Chest Surgery
• /
• v.18 no.4
• /
• pp.806-811
• /
• 1985

Pulmonary arteriovenous fistula is a rare congenital vascular malformation in the lung, resulting from erroneous capillary development, with incomplete formation or disintegration of the vascular septa that would normally divide the primitive connection between the venous and arterial plexus. The pathogenesis of its symptom is that unoxygenated and desaturated arterial blood enter into the pulmonary venous system directly. Recently we have experienced a case of multiple pulmonary arteriovenous fistula in a 15 year old male patient, who presented the symptom of cyanosis and dyspnea on exertion. The operation revealed well circumscribed and multilobulated aneurysmal lesion in left lower lobe with its subpleural and posterolateral basal location, and another aneurysmal lesion in inferior lingular segment of left lung. There was no abnormal connection between the fistula and systemic circulation. The left lower lobectomy was performed along with local extirpation of the inferior lingular segment of left lung. Both lesions showed angiomatous dilatation of the various sized vessels embedded in the parenchyma microscopically. Postoperative clinical course disclosed much improvement in symptoms and in the value of blood gas analysis. The patient was discharged without any complication.

• Steel and Composite Structures
• /
• v.4 no.6
• /
• pp.489-507
• /
• 2004

The flexibility of the connection between steel and concrete largely influences the global behaviour of the composite beam. Therefore the way the connection is modelled is the key issue in its structural analysis. Here we present a new strain-based finite element formulation in which we consider non-linear material and contact models. The computational efficiency and accuracy of the formulation is proved with the comparison of our numerical results with the experimental results of Abdel Aziz (1986) obtained in a full-scale laboratory test. The shear connectors are assumed to follow a non-linear load-slip relationship proposed by Ollgaard et al. (1971). We introduce the notion of the generalized slip, which offers a better physical interpretation of the behaviour of the contact and gives an additional material slip parameter. An excellent agreement of experimental and numerical results is obtained, using only a few finite elements. This demonstrates that the present numerical approach is appropriate for the evaluation of behaviour of planar composite beams and perfect for practical calculations.

• Fire Science and Engineering
• /
• v.34 no.3
• /
• pp.76-84
• /
• 2020

Most outlet fires occur around plug pins and plug pin receivers. However, no research has been conducted on ignitions at power connection points. This study confirms the possibility of ignition after incomplete connection, using a stranded wire, to the power connection point of an outlet. The experiment was divided into basic and reproducing experiments. The basic experiment confirmed the possibility of ignition according to the number of wire strands connected to the power connection point, and it identified the characteristics of the residue after the fire. In the reproducing experiment, lamps, vacuum cleaners, and heaters were connected to an outlet to check if the ignition at the connection advanced into a fire. The fire advanced due to the heat and arc generated at the connection point, and partial losses were identified in the U-type holder and clip. Accordingly, the results demonstrate that a fire may occur when the stranded wire is incompletely connected to the outlet. Moreover, it was confirmed that the cause of a fire can be determined based on the characteristics of the residue.

• Steel and Composite Structures
• /
• v.17 no.6
• /
• pp.851-865
• /
• 2014

Full penetration welded steel moment-resisting frame (SMRF) structures with welded box sections are widely employed in steel bridges, where a large number of steel bridges have been in operation for over fifty years in Japan. Welding defects such as incomplete penetration at the beam-column connections of these existing SMRF steel bridge piers were observed during inspection. Previous experiments conducted by the authors' team indicate that gusset stiffeners (termed fillets in this study) at the beam-web-to-column-web joint of the beam-column connections may play an important role on the seismic performance of the connections. This paper aims to experimentally study the effect of the fillet radius on seismic performance of the connections with large welding defects. Four specimens with different sizes of fillet radii were loaded under quasi-static incremental cyclic loading, where different load-displacement relations and cracking behaviors were observed. The experimental results show that, as the size of the fillet radius increases, the seismic performance of the connections can be greatly improved.

• Proceedings of the KSRS Conference
• /
• 2005.10a
• /
• pp.245-245
• /
• 2005

This paper addresses the use of directional textural information for connecting road segments. In urban scene, some roads are occluded by buildings, casting shadow of buildings, trees, and cars on streets. Automatic extraction of road network from remotely sensed high resolution imagery is generally hindered by them. The results of automatic road network extraction will be incomplete. To overcome this problem, several perceptual grouping algorithms are often used based on similarity, proximity, continuation, and symmetry. Roads have directions and are connected to adjacent roads with certain angles. The directional information is used to guide road fragments connection based on roads directional inertia or characteristics of road junctions. In the primitive stage, roads are extracted with textural and direction information automatically with certain length of linearity. The primitive road fragments are connected based on the directional information to improve the road network. Experimental results show some contribution of this approach for completing road network, specifically in urban area.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.281-284
• /
• 2007

Recently, we have developed p-i-n a-Si:H single junction thin film solar cells with RF (13.56MHz) plasma enhanced chemical vapor deposition (PECVD) system, and also successfully fabricated the mini modules ($>300cm^2$), using the laser patterning technique to form an integrated series connection. The efficiency of a mini module was 7.4% ($Area=305cm^2$, Isc=0.25A, Voc=14.74V, FF=62%). To fabricate large area modules, it is important to optimise the integrated series connection, without damaging the cell. We have newly installed the laser patterning equipment that consists of two different lasers, $SHG-YVO_4$ (${\lambda}=0.532{\mu}m$) and YAG (${\lambda}=1.064{\mu}m$). The mini-modules are formed through several scribed lines such as pattern-l (front TCO), pattern-2 (PV layers) and pattern-3 (BR/back contact). However, in the case of pattern-3, a high-energy part of laser shot damaged the textured surface of the front TCO, so that the resistance between the each cells decreases due to an incomplete isolation. In this study, the re-deposition of SnOx from the front TCO, Zn (BR layer) and Al (back contact) on the sidewalls of pattern-3 scribed lines was observed. Moreover, re-crystallization of a-Si:H layers due to thermal damage by laser patterning was evaluated. These cause an increase of a leakage current, result in a low efficiency of module. To optimize a-Si:H single junction thin film modules, a laser beam profile was changed, and its effect on isolation of scribed lines is discussed in this paper.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.33 no.1
• /
• pp.127-138
• /
• 2009

This study is about the analysis on symbolic meaning and kunstwollen of Issey Miyake's art works which is influenced by various external factors such as social and cultural background, nationality and philosophy. Especially, this research focused on 'Pleats Please Issey Miyake' and 'A Piece of Cloth' which are the core of his works. The most important concept of Issey Miyake's works is the relationship of human body and a piece of cloth. Miyake's clothes has provided the time and the space where inspires the vitality into wearer. He accomplishes the most perfect beauty through incomplete beauty of cloth. Miyake wants to express the emotion of the human being through his clothes and tries to make special code between creator, wearer and viewer. Fashion is accomplished in connection with human body, not exists just as 'clothes'. Fashion has valued as an art which expresses the ideology and the sentiment of human being most directly. Issey Miyake who has tried to express human life and emotion has promoted fashion as an important part of art. Miyake is accepting and delivering the history and culture, expressing and communicating empathy, and combining the different fields harmoniously.