• 한국정밀공학회지
• /
• 제23권9호
• /
• pp.47-53
• /
• 2006

An Experiment was carried out to find the scheme far minimization of burr formation on inclined exit surface in drilling. Several drills with different geometry are used for drilling the workpiece with inclined exit surface. Step drills are specified with step angle and step size. The influence of the inclination angle of exit surface on burr formation was observed, which enables to analyze the burr formation mechanism on inclined exit surface. Along the edge on the inclined exit surface, burrs are formed by the bending deflection to feed direction and also burrs are formed in exit direction of cutting edge. To minimize the burr formed in feed direction, the corner angle which is formed by the inclination angle and step angle must be large enough not to be bent to burr. By decreasing step angle of drill and decreasing the distance between two axes of two holes, burr formation at the intersecting holes can be minimized. Burr formation mechanisms are analyzed according to the drill geometries and cutting conditions. Several schemes far burr minimization on inclined exit surface were proposed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1253-1256
• /
• 2005

An Experiment was carried out to study burr minimization in drilling on the inclined exit surface. Several different drills, exit surface angles and cutting conditions were selected to determine their influences on burr formation. In drilling operation, there are not only flat exit surfaces but also inclined exit surfaces which is described as inclination angle. Inclination of exit surface causes a quiet different burr formation when comparing with flat surface. Burr formation mechanisms are analyzed according to the drill geometries and cutting conditions. Several schemes for burr minimization on inclined exit surface were proposed. Burr geometry in each drill and cutting condition are measured by laser measurement system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.31-32
• /
• 2011

• 설비공학논문집
• /
• 제22권1호
• /
• pp.33-39
• /
• 2010

The film boiling heat transfer was experimentally investigated for the water sprays impacting on an inclined hot surface. Full cone spray nozzles were employed for the spray cooling experiment, and experiments were made for different inclination angles of $\theta=0^{\circ}$, $15^{\circ}$, $30^{\circ}$ and $45^{\circ}$. The experimental results show that, in the downstream region of the inclined hot surface, increasing the inclination angle increases the local heat flux slowly because of increasing the number of rebound droplets. However, the inclination angle of heat transfer surface had no remarkable effect on the local heat flux of spray cooling under the present test conditions.

• 대한기계학회논문집
• /
• 제18권7호
• /
• pp.1799-1807
• /
• 1994

Natural convection from a slightly inclined circular cylinders immersed in quiescent cold pure water was studied experimentally. The experiment was carried out for circular cylinders with uniform heat flux ranging from $100W/m^{2} to 800 W/m^{2}$ and inclined angle ranging from horizontal $({\phi}=0^{\circ}) to 15^{\circ}$. The flow fields around cylinder were visualized and heat transfer characteristics investigated by measuring the surface temperatures for each case. As the results, it is shown that flow patterns are changed consecutively through the sequence of steady state downflow, unsteady state flow and steady state upflow with increasing heat flux. At the same inclined angle, as heat flux increases, the average Nusselt number decreases and then increases. At the same heat flux, as inclined angle increases, the average Nusselt number decreases.

• Ocean Systems Engineering
• /
• 제10권1호
• /
• pp.49-65
• /
• 2020

In this study, the effects of inclined shaft angle on the hydro-acoustic performance of cavitating marine propellers are investigated by a numerical method developed before and Brown's empirical formula. The cavitating blades are represented by source and vortex elements. The cavity characteristics of the blades such as cavitation form, cavity volume, cavity length etc., are computed at a given cavitation number and at a set advance coefficient. A lifting surface method is applied for these calculations. The numerical lifting surface method is validated with experimental results of DTMB 4119 model benchmark propeller. After calculation of hydrodynamic characteristics of the cavitating propeller, noise spectrum and overall sound pressure level (OASPL) are computed by Brown's equation. This empirical equation is also validated with another numerical results found in the literature. The effects of inclined shaft angle on thrust coefficient, torque coefficient, efficiency and OASPL values are examined by a parametric study. By modifying the inclination angles of propeller, the thrust, torque, efficiency and OASPL are computed and compared with each other. The influence of the inclined shaft angle on cavity patterns on the blades are also discussed.

• 한국지반환경공학회 논문집
• /
• 제17권7호
• /
• pp.27-33
• /
• 2016

This study expanded Terzaghi arching formula, which assumed a vertical surface as a sliding surface, to consider an arbitrarily inclined surface as a sliding surface and examined the effect of a sliding surface. This study firstly developed a formula to expand the existing Terzaghi arching formula to consider an inclined surface as well as a vertical surface as a sliding surface under the downward movement of a trap door. Using the expanded formula, the effect of excavation, ground, and surcharge conditions on a vertical stress was examined and the results were compared with them from Terzaghi arching formula. The comparison indicated that the induced vertical stress was highly affected by the angle of an inclined sliding surface and the degree of influence depended on the excavation, ground, and surcharge conditions. It is expected that the results from this study would provide a better understanding of various arching phenomenon in the future.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.944-947
• /
• 2000

Sculptured surface machining plays a vital role in the process of bring new products to the market place. A great variety of products rely on this technology for the production of the dies and moulds used in manufacturing. And, the use of CNC machines and CAD/CAM system has become a vital parts of product development process. The propose of this study is to investigate the effect of cutting parameters on the machinability such as surface roughness and cusp generated in the machining of sculptured surface on a three-axis CNC machining center using the CAD/CAM system. Experimental result showed that: In step down cutting, as the inclined angle of surface became smaller, the cusp height appeared higher. On the other hand, in step over cutting, as the inclined angle of surface became larger, the cusp height appeared higher. In the point of precision machining, step over cutting was more effective. For the minimization of cusp height, step down cutting was effective in larger inclined surface, but step over cutting in smaller inclined surface.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.773-776
• /
• 2005

An Experiment was carried out to study deburring in frilling hole on the Inclined exit surface. Two different deburring tools, exit surface angles, materials and cutting conditions were selected to check their performance using CNC machining center. In deburring operation, there are not only flat exit surfaces but also inclined exit surfaces which is described as inclination angle. Inclination of exit surface causes a quite different burr formation when comparing with flat surface. Deburring characteristics are analyzed according to the deburring tools and cutting conditions. Several strategies for a effective deburring on inclined exit surface were proposed.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2001년도 춘계학술대회 논문집
• /
• pp.108-119
• /
• 2001

The Spectral Analysis of surface Waves(SASW) Method has a great has a great potential for rapid determination of shear wave velocity profile of ground. However, it has an inherent limitation in the interpretation of test results due to the assumption that the ground is layered horizontally. The reason of the assumption is that difficulties exist in obtaining analytical solutions of wave equation when a soil system is composed of inclined soil layer. In this study, a finite-element method has been employed to assess the effects of dip angle and stiffness contrast of inclined soil layers and the testing direction on the dispersion curve. The propagation of wave front in the inclined soil layer was also investigated. The results indicated that the influence of dip angle on the dispersion curve is getting obvious as the dip angle increases and the propagation of wave front in the inclined layer also entirely different compared with the case of the horizontal layer.