• Journal of the Korean GEO-environmental Society
• /
• v.17 no.7
• /
• pp.27-33
• /
• 2016

This study expanded Terzaghi arching formula, which assumed a vertical surface as a sliding surface, to consider an arbitrarily inclined surface as a sliding surface and examined the effect of a sliding surface. This study firstly developed a formula to expand the existing Terzaghi arching formula to consider an inclined surface as well as a vertical surface as a sliding surface under the downward movement of a trap door. Using the expanded formula, the effect of excavation, ground, and surcharge conditions on a vertical stress was examined and the results were compared with them from Terzaghi arching formula. The comparison indicated that the induced vertical stress was highly affected by the angle of an inclined sliding surface and the degree of influence depended on the excavation, ground, and surcharge conditions. It is expected that the results from this study would provide a better understanding of various arching phenomenon in the future.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.9 s.186
• /
• pp.47-53
• /
• 2006

An Experiment was carried out to find the scheme far minimization of burr formation on inclined exit surface in drilling. Several drills with different geometry are used for drilling the workpiece with inclined exit surface. Step drills are specified with step angle and step size. The influence of the inclination angle of exit surface on burr formation was observed, which enables to analyze the burr formation mechanism on inclined exit surface. Along the edge on the inclined exit surface, burrs are formed by the bending deflection to feed direction and also burrs are formed in exit direction of cutting edge. To minimize the burr formed in feed direction, the corner angle which is formed by the inclination angle and step angle must be large enough not to be bent to burr. By decreasing step angle of drill and decreasing the distance between two axes of two holes, burr formation at the intersecting holes can be minimized. Burr formation mechanisms are analyzed according to the drill geometries and cutting conditions. Several schemes far burr minimization on inclined exit surface were proposed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1253-1256
• /
• 2005

An Experiment was carried out to study burr minimization in drilling on the inclined exit surface. Several different drills, exit surface angles and cutting conditions were selected to determine their influences on burr formation. In drilling operation, there are not only flat exit surfaces but also inclined exit surfaces which is described as inclination angle. Inclination of exit surface causes a quiet different burr formation when comparing with flat surface. Burr formation mechanisms are analyzed according to the drill geometries and cutting conditions. Several schemes for burr minimization on inclined exit surface were proposed. Burr geometry in each drill and cutting condition are measured by laser measurement system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.773-776
• /
• 2005

An Experiment was carried out to study deburring in frilling hole on the Inclined exit surface. Two different deburring tools, exit surface angles, materials and cutting conditions were selected to check their performance using CNC machining center. In deburring operation, there are not only flat exit surfaces but also inclined exit surfaces which is described as inclination angle. Inclination of exit surface causes a quite different burr formation when comparing with flat surface. Deburring characteristics are analyzed according to the deburring tools and cutting conditions. Several strategies for a effective deburring on inclined exit surface were proposed.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.2
• /
• pp.137-143
• /
• 1999

The study of the high speed machining of inclined plane using ball end mill is performed. The use of ball end mill is rapidly growing in die and mold manufacturing. The cutting characteristics, such as cuttin g force, surface roughness and surface profile, are varied according to the variation of cutting directions. Free surface is cut using ball end mill, the surface profile is greatly varied depending upon the cutting direction. So this study will deal with the characteristics of cutting such as cutting efficiency according to the inclined plane of the workpiece, the cutting force according to tool path, surface profile and the roughness of surface. The optimal cutting direction to be applied the cutting for 3-D sculptured surfaces can be show through the results of this study.

• The Journal of Korean Physical Therapy
• /
• v.24 no.6
• /
• pp.383-387
• /
• 2012

Purpose: Rising from a chair is important for activities of daily living. Several factors have influence on sit-to-stand movement. We studied the effect of inclination of seat surface of on the movement of rising from a chair with electromyographic (EMG). Methods: Twelve subjects performed the sit-to-stand movement on anterior-inclined, standard, and posterior inclined chair. We measured onset time of tibialis anterior and rectus femoris with EMG on each inclination chair. Results: The onset time at the anterior-inclined chair is significantly faster than it at the standard chair (p<0.05). And the onset time at the posterior-inclined chair is significantly slower than it at the standard chair (p<0.05). Conclusion: Rising from anterior inclined chair appeared to be more effective than rising from the standard and posterior inclined chair. Therefore, this finding suggests that the selection of set surface inclination must be considered for activities of daily living during rehabilitation.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.1
• /
• pp.33-39
• /
• 2010

The film boiling heat transfer was experimentally investigated for the water sprays impacting on an inclined hot surface. Full cone spray nozzles were employed for the spray cooling experiment, and experiments were made for different inclination angles of $\theta=0^{\circ}$, $15^{\circ}$, $30^{\circ}$ and $45^{\circ}$. The experimental results show that, in the downstream region of the inclined hot surface, increasing the inclination angle increases the local heat flux slowly because of increasing the number of rebound droplets. However, the inclination angle of heat transfer surface had no remarkable effect on the local heat flux of spray cooling under the present test conditions.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.04a
• /
• pp.15-20
• /
• 2004

Inclined surface milling in the mould and die industries is one of the most commonly needed cutting process. For the variety and complexity of cutting characteristics in various cutting condition, it is difficult to select a optimal tool path orientation. The comparative results through FFT analysis in this study provide a guideline for the selection tool path orientation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.944-947
• /
• 2000

Sculptured surface machining plays a vital role in the process of bring new products to the market place. A great variety of products rely on this technology for the production of the dies and moulds used in manufacturing. And, the use of CNC machines and CAD/CAM system has become a vital parts of product development process. The propose of this study is to investigate the effect of cutting parameters on the machinability such as surface roughness and cusp generated in the machining of sculptured surface on a three-axis CNC machining center using the CAD/CAM system. Experimental result showed that: In step down cutting, as the inclined angle of surface became smaller, the cusp height appeared higher. On the other hand, in step over cutting, as the inclined angle of surface became larger, the cusp height appeared higher. In the point of precision machining, step over cutting was more effective. For the minimization of cusp height, step down cutting was effective in larger inclined surface, but step over cutting in smaller inclined surface.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.31 no.2
• /
• pp.11-18
• /
• 2008

Surface roughness is an important factor to evaluate machined parts in precision machining. This is the major measure of surface quality. This research sets up experiments to select the factors which affect surface roughness in the machining of inclined planes of aluminum. The levels of the selected experimental factors are chosen to evaluate the relationship between the surface roughness of the machined parts and machining parameters. This is to find out the optimal machining condition in the inclined planes. The objective of this research is to improve the surface roughness of the machined products by using the ANOVA analysis. The factors for the experiments are cutting speed, feed rate, cutting depth, and cutting width. The experimental levels of the factors are two for the cutting depth and width. For the cutting speed and feed rate, their levels are three because they are more sensitive for the surface roughness than the other two. The inclined planes are machined by 5-axis machining equipment.