• The Bulletin of The Korean Astronomical Society
• /
• v.38 no.1
• /
• pp.62.2-62.2
• /
• 2013

It is considered that comets near the ecliptic plane have been injected into inner solar system from Kuiper-belt. Some of them are still active while others are dormant with no detectable tails and comae. These dormant comets have eccentric and/or inclined orbits, which are parameterized by Tisserand parameter TJ<3. In addition, dormant comets can be differentiated from asteroids based on the albedo, because they have low albedo (the geometrical albedos pv<0.1). The conditions of TJ<3 and pv<0.1 have been used as a criteria to discriminate dormant comets from asteroids. However, we must be more careful because there are 'contaminations' from the outer region, i.e. Jovian Trojans (5.05

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.495-496
• /
• 2008

This paper describes the influence of Ultra-violet irradiation on time to tracking resistance of epoxy insulating materials by use of the inclined plane test. And, the influence of surface degradation was evaluated through several method such as measurement of contact angle, surface roughness, using a scanning electron microscopy. As the 1000 hours of the surface degradation with UV-CON, the flashover time decreases at different rates depending on epoxy resin and silicone rubber specimen. As the duration of the surface degradation with UV-CON is prolonged, the contact angle of epoxy resin decreases at the rate of degradation time, while that of silicone rubber was not exchanged. It is assumed that this phenomenon is related to the decrease in hydrophobicity of the surface of the materials. Also, as to epoxy resin, the decrease of hydrophobicity due to surface degradation with UV-CON is greater than that resulting from surface degradation with WOM. The UV radiation produced chalking and crazing on the surface of the insulating materials specimen.

• Structural Engineering and Mechanics
• /
• v.15 no.1
• /
• pp.115-134
• /
• 2003

The Ting Kau Bridge in Hong Kong is a cable-stayed bridge comprising two main spans and two side spans. The bridge deck is supported by three towers, an end pier and an abutment. Each of the three towers consists of a single reinforced concrete mast which reduces its section in steps, and it is strengthened by transverse cables and struts in the transverse vertical plane. The bridge deck is supported by four inclined planes of cables emanating from anchorages at the tower tops. In view of the threat from typhoons, the dynamic behaviour of long-span cable-supported bridges in the region is always an important consideration in their design. This paper is devoted to the ambient vibration measurements of the bridge for evaluation of dynamic characteristics including the natural frequencies and mode shapes. It also describes the modelling of the bridge. A few finite element models are developed and calibrated to match with the field data and the results of subsequent structural health monitoring of the bridge.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.10
• /
• pp.1314-1325
• /
• 1997

Experiments have been conducted to determine the flow and heat transfer characteristics for a two-dimensional turbulent wall attaching offset jet at different oblique angles to a flat surface. The distributions of the wall static pressure coefficient and time-averaged reattachment position for various offset ratios and oblique angles have been measured. The local Nusselt number distributions on the plate surface were also measured using liquid crystal as a temperature indicator. The new hue-capturing technique utilizing a true color image processing system was used to accurately determine the temperature of the liquid crystal. The experiments were carried out at Reynolds number, Re (based on D) of from 7300 to 21,300 with offset ratio, H/D from 2.5 to 10, and oblique angle, .alpha. from 0 deg. to 400 deg..

• Earthquakes and Structures
• /
• v.21 no.6
• /
• pp.601-612
• /
• 2021

The paper concerns the selection of a design accelerograms used for the slope stability assessment under earthquake excitation. The aim is to experimentally verify the Arias Intensity as an indicator of the excitation threat to the slope stability. A simple dynamic system consisting of a rigid block on a rigid inclined plane subjected to horizontal excitation is adopted as a slope model. Strong ground motions recorded during earthquakes are reproduced on a shaking table. The permanent displacement of the block serves as a slope stability indicator. Original research stand allows us to analyse not only the relative displacement but also the acceleration time history of the block. The experiments demonstrate that the Arias Intensity of the accelerogram is a good indicator of excitation threat to the stability of the slope. The numerical analyses conducted using the experimentally verified extended Newmark's method indicate that both the Arias Intensity and the peak velocity of the excitation are good indicators of the impact of dynamic excitation on the dam's stability. The selection can be refined using complementary information, which is the dominant frequency and duration of the strong motion phase of the excitation, respectively.

• The Bulletin of The Korean Astronomical Society
• /
• v.44 no.2
• /
• pp.40.3-40.3
• /
• 2019

Our recent observations of the Sun through strong spectral lines have revealed several important properties of the three-minute umbral oscillations inside sunspots -- the oscillations of intensity and Doppler velocity with periods of 2 to 3 minutes. The oscillations usually occur in the form of a time series of oscillation packets each of which lasts 10 to 20 minutes, not as continuous trains. Each oscillation packet is characterized by a singly peaked power spectrum of velocity oscillation. The oscillations propagate in the vertical direction from the photosphere to the corona. In the upper chromosphere, they develop into shocks that eventually collide with the transition region. When shocks propagate along a highly inclined direction, the merging of two successive shocks can take place. Once they enter the corona, they change to linear compressional waves. In the image plane, the three-minute oscillations propagate with high speeds in the transverse direction as well, usually propagating radially outwards from a point, and sometimes accompanying spiraling patterns of Doppler velocity. These observational properties can be theoretically explained by postulating the spatio-temporally localized source of fast MHD waves at a depth of about 2000 km below the surface, the excitation of slow MHD waves via mode conversion near the photosphere, and the resonance of the slow waves in the photospheric layer below the temperature minimum, and the nonlinear development of slow waves in the chromosphere.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.11
• /
• pp.45-51
• /
• 1995

In order to suggest the proper cutting conditons of the CNC milling machining for the free-form surface, some experments were carried out. In the experiments, the influence of cutting conditions on a inclined spherical surface were examined by geometrical analysis. In this study, the roundness and cutting force were measured to know the effect of several cutting conditions on the machined surface and the cutting characteristics were carefully investigated. The results obtained in this study are aw follows. 1) If the tool ha s enough rigidity, we can get better dimensional accuracy in up-ward cutting than down- ward cutting. 2) A great roundness error is appeared on the surface declined under 30 degress to the horizontal plane in circular machining by a bal end mill. 3) If the thrust force is increased, the stability of tool is decreased. And the phenomenon is apperared in great in down-ward cutting than up-ward cutting.

• The korean journal of orthodontics
• /
• v.32 no.2 s.91
• /
• pp.91-105
• /
• 2002

In general, orthodontists make problem lists and treatment plans based on norms of several cephalometric standards. But consideration of dentoalveolar compensation, which tends to maintain normal dental arch relationship in various skeletal jaw relationships, helps orthodontists make more individualized treatment objectives and plans. The purpose of this study was to classify skeletal patterns of normal occlusion samples by cluster analysis and to investigate the dentoalveolar compensation according to skeletal patterns. The subjects were consisted of 125 subjects who were normal occlusion samples at Seoul National University Dental Hospital, Department of Orthodontics. Lateral cephalograms in centric occlusion were traced and digitized. The skeletal patterns of normal occlusion samples were classified into three horizontal groups and three vertical groups by cluster analysis and ANOVA on the skeletal and dentoalveolar measurements among the groups were carried out. The results were as follows ; 1. Anteroposterior and vertical skeletal relationships of normal occlusion samples were very variable. 2. As the mandibular position was anterior to the maxilla, the maxillary incisors inclined more labially, the mandibular incisors more lingually, and the occlusal plane was flattened due to the anteroposterior dentoalveolar compensation. dentoalveolar height was decreased and upper posterior teeth was uprighted to the palatal plane and lower incisors and lower posterior teeth to the mandibular plane. 4. Lower incisors were more strongly associated with the dentoalveolar compensation than upper incisors according to the anteroposterior and vertical skeletal relationship.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.30 no.1
• /
• pp.76-83
• /
• 1985

A hypothesis that artificial reforming of corn canopy could improve solar light penetration and dry matter production was tested in corn fields (var. Suwon 19) with three planting densities; low (60 ${\times}$ 40cm), medium (60 ${\times}$ 24cm) and high (60 ${\times}$ 16cm). Natural canopy was found that leaf orientations were even over all azimuth but somewhat inclined toward north-south direction and leaf angle ranged 38$^{\circ}$ to 71$^{\circ}$ from horizontal surface. Reforming corn canopy included following treatments: 1) natural canopy planted in north-south rows (natural canopy), 2)east-west plane canopy planted in north-south rows (E-W canopy), 3)east-west plane canopy and upright leaves in north-south rows, 4)north-south plane canopy (N-S canopy) in east-west rows. After corn plots were installed with training system by supporting poles and connecting wires, corn leaves were induced to a reforming direction and tied on wire. Average light intensity at the mid-point of plant height showed 5-10% increases in E-W canopy and in E-W canopy plus upright leaves, but a 2-10% decrease in N-S canopy from natural canopy. At yellow ripe stage, total dry wt. was increased in E-W canopy but not in N-S canopy. The E-W canopy produced 3-10% more grain yield than natural canopy. Though E-W canopy plus upright leaves yielded less at low density, it yielded up to 10% more at higher density. The N-S canopy yielded similar to low compared with natural canopy. These results suggests that reforming canopy toward solar incident direction increases light penetration into lower canopy, photosynthetic efficiency and grain yield, especially at high planting density in corn.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.1A
• /
• pp.11-18
• /
• 2012

This paper deals with the numerical determination of the stress intensity factors of cracked aluminum plates under the mixed mode of $K_I$ and $K_{II}$ in glass-epoxy fiber reinforced composites. For the stress intensity factors, two different models are reviewed such as VCCT and two-step extension method. The p-convergent partial layerwise model is adopted to determine the fracture parameters in terms of energy release rates and stress intensity factors. The p-convergent approach is based on the concept of subparametric element. In assumed displacement field, strain-displacement relations and 3-D constitutive equations of a layer are obtained by combination of 2-D and 1-D higher-order shape functions. In the elements, Lobatto shape functions and Gauss-Lobatto technique are employed to interpolate displacement fields and to implement numerical quadrature. Using the models and techniques considered, effects of composite laminate configuration according to inclined angles and adhesive properties on the performance of bonded composite patch are investigated. In addition to these, the out-of-plane bending effect has been investigated across the thickness of patch repaired laminate plates due to the change of neutral axis. The present model provides accuracy and simplicity in terms of stress intensity factors, stress distribution, number of degrees of freedom, and energy release rates as compared with previous works in literatures.