• Journal of the Korean GEO-environmental Society
• /
• v.13 no.12
• /
• pp.59-66
• /
• 2012

In this study, it was sampling from heavy metal-contaminated soil with the waste in railroad workshop. And, the pollution concentration and analysis of particle-size distribution were conducted to design efficient purification process that it was aimed at high contaminated area, low contaminated area and samples containing waste foundry sand. But, it was the other signs of general soil contamination, as construction waste of waste concrete and waste wood, waste foundry sand, incinerator ash, etc is overall buried on the grounds. Thus, the common heavy metal purification technology has not decreased the pollution. However, heavy-metal contamination was reduced by magnetic separation utilizing the magnetic component of the mixed waste.

• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.3
• /
• pp.273-278
• /
• 2007

Modern society has moved from a phosphorus recycling loop, where animal manure and human wastes were spread on farming land to recycle nutrients, to a once-through system, where phosphates are extracted from mined, non-renewable phosphate rock and end up either in landfill(sewage sludge, incinerator ash) or in surface waters. In this research, crystallization of nitrogen and phosphate with natural sources of $Mg^{2+}$ in synthetic water was tested. The operational parameters of pH, mixing time, and the magnesium molar ratio were investigated to find optimal conditions of the MAP precipitation using synthetic wastewater. The removal efficiency of phosphate increased with pH up to 11. By MAP precipitaiton of the synthetic waste water, 94% of the phosphate were eliminated at pH 11. It was found that at least 10 minutes mixing time was required and 20 minutes mixing time was recommended for efficient phosphate removal. High efficiency removal of phosphate was possible when the magnesium molar ratio was 1.0~2.0. The comparative study of different magnesium sources showed that coagulants (PAC) was the more efficient sources than only magnesium. The result showed that 97% of phosphate removal. In conclusion, coagulants (PAC) induced crystallization of struvite and hydroxyapatite was shown to be a technically viable process that could prove cost effective for removing phosphate in wastewater.

• Clean Technology
• /
• v.22 no.1
• /
• pp.1-8
• /
• 2016

Rapid growth in nanotechnology promise novel benefits through the exploitation of their unique industrial applications. However, as increasing of production amount of nanomaterials, their unintentional exposure to the environment has been caused. Therefore, there is a need for effective management of nanowaste to the sustainable nanotechnology. One possible endpoint at the environmental exposure scenario for nanowaste treatment is incineration. Although a few study on the incineration of nanomaterials was reported, pioneering researchers found that although it is possible to incinerate nanowaste without releasing nanoparticles into the atmosphere, the residues (bottom ash or slag) with nanomaterials eventually end up in landfills. Though there are still many questions to understand the fate of nanomaterials in incinerator, firstly we have to study whether nanowaste treatment via incineration is safe to human and environment.

• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.4
• /
• pp.413-420
• /
• 2008

In order to utilize cinder melting slag as a filter media to control the quality of early rainwater, its environmental stability was verified by heavy metal elution experiment and improved by pre-treatment. Possibilities of improving its function as an absorbent was considered. Absorption characteristics of melting slag before and after the pre-treatment were analyzed by heavy metal equilibrium and stationary-phase column experiments, which in turn were analyzed by comparison experiment with activated carbon. As a result of heavy metal elution experiment, every metal item existed in a much lower amount than the criteria or was not detected, implying that there is no problem recycling it. Absorption equilibrium experiment showed that the time for pre-treatment melting slag to reach the equilibrium was reduced, while the absorbed amount was greatly increased. Stationary-phase column experiment assures us that the elimination rate was not changed much by influx rate, pH and the change in packing volume rate, indicating that this melting slag can be used not only as a filter media to control the quality of early rainwater but also in many areas of water-processing.

• Resources Recycling
• /
• v.16 no.3 s.77
• /
• pp.19-26
• /
• 2007

The bottom ash of municipal solid waste incineration generated during incineration of municipal solid waste in metropolitan area consists of ceramics, glasses, ferrous materials, combustible materials and food waste and so on. Although the ferrous material was separated by the magnetic separation before the incineration process, of which content accounts for about $3{\sim}11%$ in bottom ash. The formation of a $Fe_3O_4-Fe_2O_3$ double layer(similar to pure Fe) on the iron surface was found during air-annealing in the incinerator at $1000^{\circ}C$. A strong thermal shock, such as that takes place during water-cooling of bottom ash, leads to the breakdown of this oxidation layer, facilitating the degradation of ferrous metals and the formation of corrosion products and it existed as $Fe_2O_3,\;Fe_3O_4\;and\;FeS_2$. So, many problems could occur in the use of bottom ash as an aggregate substitutes in construction field. Therefore, in this study, the separation of ferrous materials from municipal solid waste incineration bottom ash was investigated. In the result, the ferrous product(such as $Fe_2O_3,\;Fe_3O_4,\;FeS_2$ and iron) by magnetic separator at 3800 gauss per total bottom ash(w/w.%) accounted for about 18.7%, and 87.7% of the ferrous product was in the size over 1.18 mm. Also the iron per total bottom ash accounted for about 3.8% and the majority of it was in the size over 1.18 mm.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.17 no.3
• /
• pp.91-99
• /
• 2009

This research were performed to evaluate co-incineration characteristics of sewage sludge and industrial waste in rotary kiln incinerator, and provide the fundamental data. Plastic portion (42.55%) in this industrial waste showed over 3 times higher than that (11.92%) of paper. Korean proximate analysis of the waste mixed with sewage sludge and industrial waste (3 : 7, volumetric basis) showed 16.3% of moisture, 70.5% of volatile solids, and 13.2% of ash, respectively. Low heating value of the mixed waste was 4,513kcal/kg. So it was thought that the mixed waste of sewage sludge and industrial waste (containing 43% of plastics and 12% papers) has enough heating value for co-incineration. The incineration of mixed waste showed the lowest SOx and NOx concentrations at $700^{\circ}C$. However, the operation at $950^{\circ}C$ was feasible in considering dioxin and the other hazardous gases. It was concluded that use of $Ca(OH)_2$ should be under investigation for the operation at $950^{\circ}C$.

• Clean Technology
• /
• v.6 no.1
• /
• pp.61-69
• /
• 2000

In this study, generation process and properties of inorganic industrial waste which can be used in cement industry were investigated. The scheme of recycling to use the selected waste as raw materials, mineralizer and flux, admixture and raw materials for special cement was decided and then various experiments were carried out. The experimental results were as follows ; In the use of industrial waste as raw materials, ferrous materials could be substituted by Cu-slag, Zn-slag, electric arc furnace or convertor furnace slag etc., and a siliceous material could be substituted by sand from cast-iron industry. By-products from sugar or fertilizer industry, which has $CaF_2$ as the main component, and jarosite from Zn refinery enabled clinker phases to be formed at lower temperature by $100{\sim}150^{\circ}C$. Adding Cu slag and STS sludge in proper proportion to cement improved properties of cement. Fly ash and limestone powder as admixture had the same effect on cement. As a raw material for special cement, aluminium waste sludge could be used in making ultra early strength cement, which had the compressive strength of $300kg/cm^2$ within 2hours. And two different ashes from municipal incinerator could be raw materials of the cement which was mainly composed of $C_3S$ and $C_{11}A_7{\cdot}CaCl_2$ as clinker phases.

• Journal of the Korean GEO-environmental Society
• /
• v.10 no.3
• /
• pp.47-52
• /
• 2009

The comparative analysis on physico-chemical characteristics of municipal solid waste from dwelling site and landfill site were performed to provide the fundamental information of waste management in Chungju city. It was analysed and evaluated the bulk density, physical component, three major component, chemical component, and heating value of MSW. The physical components depended on the sampling site in dwelling site and landfill site. But, by the ultimate analysis, the chemical composition was almost similar to result for municipal solid waste from dwelling site and landfill site. Therefore, it is necessary to investigate the physical components according to sampling site for the MBT to introduce for combustible municipal solid waste pre-treatment, but it needs the chemical composition from landfill site to design the incinerator. The physical composition showed that the combustible and the noncombustible occupied 87.4% and 12.6% respectively. In case of three component analysis, the moisture, the combustible, and the ash were 27.6, 60.5, 11.9% respectively. The chemical composition through the element analysis were C (50.1%), H (6%), O (39.5%), N (1.9%), S (0.5%), and Cl (1.3%).

• Journal of the Korea Organic Resources Recycling Association
• /
• v.26 no.3
• /
• pp.55-61
• /
• 2018

This study evaluated if the selected samples meets the Solid Refuse Fuel quality criteria in Korea. Biomass and plastic wastes generated in D City were mixed in diverse ratio. When the biomass content was about 40%, the moisture content was close to the SRF criteria and was measured to be 9.8%. The ash contents were analyzed up to 4.19%, and the lower calorific values based on Steuer, Dulong Equation and Bomb Calorimeter were at least 4,851, 4,181 and 3,847 kcal/kg, respectively. As a result of the elemental analysis, sulfur and chloride content were measured up to 0.05%. Those values satisfied the SRF criteria. Also, heavy metals(Hg, Cd, Pb, As) were analyzed to be below the SRF criteria. This makes it possible to use efficiently the wood byproducts abandoned in the woods, and the physical properties of wood being weak to moisture can be supplemented with plastics. Consequently, if plastic and biomass were well mixed and made into SRF, it would overcome the problem of shortening the life span of incineration facilities due to the high temperature of plastic wastes in the incinerator.

• Journal of the Mineralogical Society of Korea
• /
• v.20 no.4
• /
• pp.267-275
• /
• 2007

Melting slag generated from municipal-incinerator ash contains lots of impurities which have adverse effects on zeolite synthesis. These impurities are detrimental to zeolite synthesis, and the yield and purity of zeolite was decreased. And thus its performance is lowered. In melting slag, there are lots of components such as $Fe_2O_3$, FeO and CaO. To remove these impurities, we treated the melting slag with hydrochloric acid at initial pH 1, 3, 5, and 7. After the treatment, the $SiO_2,\;Fe_2O_3,\;and\;TiO_2$ ratios increased, but the $Al_2O_3,\;FeO,\;CaO,\;Na_2O$ and MgO ratios decreased. We reacted these treated slag in a NaOH solution under hydrothermal conditions at $80^{\circ}C$. The hydrothermal products from the slag and the slag treated at pH 7 and pH 5 were determined to be tobermorite, whereas those at pH 3 and pH 1, Na-P1 and Na-X zoelite respectively. CaO was found to inhibit the synthesis of zeolite.