• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.166-166
• /
• 2010

Recently, TFTs based on amorphous oxide semiconductors (AOSs) such as ZnO, InZnO, ZnSnO, GaZnO, TiOx, InGaZnO(IGZO), SnGaZnO, etc. have been attracting a grate deal of attention as potential alternatives to existing TFT technology to meet emerging technological demands where Si-based or organic electronics cannot provide a solution. Since, in 2003, Masuda et al. and Nomura et al. have reported on transparent TFTs using ZnO and IGZO as active layers, respectively, much efforts have been devoted to develop oxide TFTs using aforementioned amorphous oxide semiconductors as their active layers. In this thesis, I report on the performance of thin-film transistors using amorphous indium gallium zinc oxides for an active channel layer at room temperature. $SiO_2$ was employed as the gate dielectric oxide. The amorphous indium gallium zinc oxides were deposited by RF magnetron sputtering. The carrier concentration of amorphous indium gallium zinc oxide was controlled by oxygen pressure in the sputtering ambient. Devices are realized that display a threshold voltage of 1.5V and an on/off ration of > $10^9$ operated as an n-type enhancement mode with saturation mobility with $9.06\;cm^2/V{\cdot}s$. The devices show optical transmittance above 80% in the visible range. In conclusion, the fabrication and characterization of thin-film transistors using amorphous indium gallium zinc oxides for an active channel layer were reported. The operation of the devices was an n-type enhancement mode with good saturation characteristics.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.227-227
• /
• 2012

본 연구에서는 RF스퍼터링법에 의하여 glass substrate에 In-Zn-Sn-O (IZTO)를 Zn 성분에 변화를 주면서 $350{\AA}$ 만큼 증착시키고, 1시간 동안 $350^{\circ}C$로 열처리 하였다. In:Zn:Sn의 성분 비율은 20:48:32 (IZTO1), 13:60:27 (IZTO2)이다. 박막의 전자적, 광학적 특성은 XPS (X-ray Photoelectron Spectroscopy), REELS(Reflection Electron Energy Loss Spectroscopy), UV-Spectrometer를 이용하여 연구하였고, 박막의 전기적 특성은 van der Pauw 법을 이용하여 측정하였다. XPS측정결과, IZTO박막은 In-O, Sn-O and Zn-O의 결합을 가진다. REELS를 이용해 Ep=1,500 eV에서의 밴드갭을 얻어보면, $350^{\circ}C$로 열처리 한 박막은 열처리를 하지 않은 것에 비해 밴드갭이 IZTO1는 3.36 eV에서 3.54 eV로, IZTO2는 3.15 eV에서 3.31 eV로 증가하였다. 반면에 Zn 함량이 증가할수록 밴드갭이 감소하는 것을 확인할 수 있었다. 이 값은 UV-Spectrometer를 이용한 광학적 밴드갭과 일치하였다. 또한 van der Pauw method를 이용한 전기적 특성 분석 결과, 열처리를 하기 전에 비하여 carrier concentration이 IZTO1는 $-4.4822{\times}10^{18}cm^{-3}$에서 $-2.714{\times}10^{19}cm^{-3}$로, IZTO2는 $-3.6931{\times}10^{17}cm^{-3}$에서 $-1.7679{\times}10^{19}cm^{-3}$로 증가하였다. 반면에 Resistivity는 IZTO1의 경우 $1.7122{\times}10^{-1}{\Omega}{\cdot}cm$에서 $5.5496{\times}10^{-3}{\Omega}{\cdot}cm$로, IZTO2는 $1.3290 {\Omega}{\cdot}cm$에서 $1.3395{\times}10^{-2}{\Omega}{\cdot}cm$로 감소하였다. 그리고 UV-Spectrometer를 이용한 광학적 특성을 측정해본 결과, 가시광선영역인 380~780 nm에서의 투과율이 83%이상으로 투명전자소자로의 응용이 가능하다는 것을 보여주었다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.297-298
• /
• 2015

우수한 열전 성능의 소자가 되기 위해서는 높은 전기 전도도 및 제백상수 그리고 낮은 열 전도도를 가져야한다. 본 연구에서는 DC 마그네트론 스퍼터링 법을 이용하여 비정질 구조를 갖는 ITZO 박막을 제작하였으며, 전기적 특성과 열전 특성을 조사하였다. 그 결과 ITO에 ZnO 첨가시 전기적 특성 및 열전 특성이 향상 되었다. 또한 비정질 구조를 가지므로 격자에 의한 열 전도도가 낮아 전체 열 전도도가 낮을 것이며 이는 높은 열전 성능 지수(ZT)를 가질 것이라 예상된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.543-543
• /
• 2013

Thin-film transistors (TFTs) based on oxide semiconductors have been regarded as promising alternatives for conventional amorphous and polycrystalline silicon TFTs. Oxide TFTs have several advantages, such as low temperature processing, transparency and high field-effect mobility. Lots of oxide semiconductors for example ZnO, SnO2, In2O3, InZnO, ZnSnO, and InGaZnO etc. have been researched. Particularly, zinc-tin oxide (ZTO) is suitable for channel layer of oxide TFTs having a high mobility that Sn in ZTO can improve the carrier transport by overlapping orbital. However, some issues related to the ZTO TFT electrical performance still remain to be resolved, such as obtaining good electrical contact between source/drain (S/D) electrodes and active channel layer. In this study, the bottom-gate type ZTO TFTs with staggered structure were prepared. Thin films of ZTO (40 nm thick) were deposited by DC magnetron sputtering and performed at room temperature in an Ar atmosphere with an oxygen partial pressure of 10%. After annealing the thin films of ZTO at $400^{\circ}C$ or an hour, Cu, Mo, ITO and Ti electrodes were used for the S/D electrodes. Cu, Mo, ITO and Ti (200 nm thick) were also deposited by DC magnetron sputtering at room temperature. The channel layer and S/D electrodes were defined using a lift-off process which resulted in a fixed width W of 100 ${\mu}m$ and channel length L varied from 10 to 50 ${\mu}m$. The TFT source/drain series resistance, the intrinsic mobility (${\mu}i$), and intrinsic threshold voltage (Vi) were extracted by transmission line method (TLM) using a series of TFTs with different channel lengths. And the performances of ZTO TFTs were measured by using HP 4145B semiconductor analyzer. The results showed that the Cu S/D electrodes had a high intrinsic field effect mobility and a low effective contact resistance compared to other electrodes such as Mo, ITO and Ti.

• New & Renewable Energy
• /
• v.3 no.4
• /
• pp.63-68
• /
• 2007

유리를 기판으로 하는 superstrate pin 비정질 실리콘 태양전진에서 전면 투명전도막(TCO)과 p-층의 계면은 태양전지 변환효율에 큰 영향을 미친다. 면투명전도막(TCO)으로 현재 일반적으로 사용되는 ZnO:Al는 $SnO_2:F$보다 전기, 광학적으로 우수하고, 안개율 (Haze)높으며, 수소 플라즈마에서 안정성이 높은 특징을 갖고 있다. 그래서 박막 태양전지의 특성향상에 매우 유리하나, 태양전지로 제조했을 때, $SnO_2$보다 충진율(Fill Factor:F.F)과 $V_{oc}$가 감소한다는 단점을 가지고 있다. 본 실험실에서는 $SnO_2:F$dml F.F.가 72%이 나온 반면 ZnO:Al의 F.F은 68%에 그쳤다. 이들 원인을 분석하기 위해 TCO/p-layer의 전기적 특성을 알아 본 결과, $SnO_2:F$보다 ZnO:Al의 직렬저항이 높게 측정되었다. 이러한 결과를 바탕으로 p-layer에 $R=(H_2/SiH_4)=25$로 변화, p ${\mu}c$-Si:H/p a-SiC:H로 p-layer 이중 증착, p-layer의 boron doping 농도를 증가시키는 실험을 하였다. 직렬저항이 가장 낮았던 p ${\mu}c$-Si:H/p a-SiC:H 인 p-layer 이중 증착에서 $V_{oc}$는 0.95V F.F는 70%이상이 나왔다. 이들 각 p층의 $E_a$(Activiation Energy)를 구해본 결과, ${\mu}c$-Si:H의 Ea 가 가장 낮은 것을 관찰 할 수 있었다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.1
• /
• pp.39-45
• /
• 2003

The varistor properties of ZnO-Pr$_{6}$O$_{11}$-CoO-based ceramics doped with Sm$_2$O$_3$were investigated in the addition range of 0.0~2.0 mol% Sm$_2$O$_3$at sintering temperature of 130$0^{\circ}C$ and 135$0^{\circ}C$. As Sm$_2$O$_3$ content is increased, the breakdown voltage was increased in the range of 348.9~521.8 V/mm for ceramics sintered at 130$0^{\circ}C$ and 8.5~381.3 V/mm for ceramics sintered at 135$0^{\circ}C$. On the whole, the increase of sintering temperature led to the low nonlinearity regardless of Sm$_2$O$_3$content. ZnO-Pr$_{6}$O$_{11}$-CoO-based ceramics doped with 1.0 mol% at each sintering temperature exhibited the most superior varistor properties, with the nonlinear exponent of 42.1 at 130$0^{\circ}C$, 36.8 at 135$0^{\circ}C$ and the leakage current of 9.2 $\mu$A at 130$0^{\circ}C$, 11.7 $\mu$A at 135$0^{\circ}C$.EX>.EX>.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.275-277
• /
• 2007

유리를 기판으로 하는 superstrate pin 비정질 태양전지에서 전면투명전도막(TCO)과 p-layer의 계면이 태양전지의 효율을 내는데 가장 큰 기여를 한다. 전면투명전도막(TCO)으로 현재 일반적으로 사용되는 ZnO:Al는 $SnO_2:F$ 보다 전기,광학적으로 우수하고, 안개율(Haze)높으며, 수소 플라즈마에서의 안정성이 높은 특정을 갖고 있다. 그래서 박막 태양전지 특성향상에 매우 유리하나, 태양전지로 제조했을 때, $SnO_2:F$보다 충진율(Fill factor:F.F)과 V_{\infty}$ 가 감소한다는 단점을 가지고 있다. 본 실험실에서는 $SnO_2:F$의 F.F가 72%이 나온 반면 ZnO:Al의 F.F은 68%에 그쳤다. 이들 원인을 분석하기 위해 TCO/p-layer의 전기적 특성을 알아 본 결과, $SnO_2:F$보다 ZnO:Al의 직렬저항이 높게 측정되었다. 이러한 결과를 바탕으로 p-layer 에 R={$H_2/SiH_4$}=25로 변화, p ${\mu$}c$-Si:H/p a-SiC:H 로 p-layer 이중 증착, p-layer의 boron doping 농도를 증가시키는 실험을 하였다. 직렬저항이 가장 낮았던 p ${\mu$}c$-Si:H/p a-SiC:H 로 p-layer 이중 증착에서 Voc는 0.95V F.F는 70% 이상이 나왔다. 이들 각 p층의 $E_a$(Activation Energy)를 구해본 결과, ${\mu$}c$-Si:H의 Ea 가 가장 낮은 것을 관찰 할 수 있었다.

• Economic and Environmental Geology
• /
• v.45 no.6
• /
• pp.623-641
• /
• 2012

The Janggun lead-zinc-silver deposit is hydrothermal-metasomatic deposit. We have sampled wallrock, hydrother-maly-altered rock and lead-zinc-silver ore vein to study the element dispersion during wallrock alteration. The hydrothermal alteration that is remarkably recognized at this deposit consists of rhodochrositization and dolomitization. Wallrock is dolomite and limestone that consisit of calcite, dolomite, quartz, phlogopite and biotite. Rhodochrosite zone occurs near lead-zinc-silver ore vein and include mainly rhodochrosite with amounts of calcite, dolomite, kutnahorite, arsenopyrite, pyrite, chalcopyrite, sphalerite, galena and stannite. Dolomite zone occurs far from lead-zinc-silver ore vein and is composed of mainly dolomite and minor calcite, rhodochrosite, pyrite, sphalerite, chalcopyrite, galena and stannite. The correlation coefficients among major, trace and rare earth elements during wallrock alteration show high positive correlations(dolomite and limestone = $Fe_2O_3(T)$/MnO, Ga/MnO and Rb/MnO), high negative correlations(dolomite = MgO/MnO, CaO/MnO, $CO_2$/MnO, Sr/MnO; limestone = CaO/MnO, Sr/MnO). Remarkable gain elements during wallrock alteration are $Fe_2O_3(T)$, MnO, As, Au, Cd, Cu, Ga, Pb, Rb, Sb, Sc, Sn and Zn. Remarkable loss elements are CaO, $CO_2$, MgO and Sr. Therefore, elements(CaO, $CO_2$, $Fe_2O_3(T)$, MgO, MnO, Ga, Pb, Rb, Sb, Sn, Sr and Zn) represent a potential tools for exploration in hydrothermal-metasomatic lead-zinc-silver deposits.

• Journal of the Korean Ceramic Society
• /
• v.12 no.1
• /
• pp.5-11
• /
• 1975

Thick film resistor paste was made utilizing oxide materials such as SnO, SnO＋Sb2O3, and SnO＋Zn. The oxide materials were mixed respectively with Q-12 glass powder and finally suspended in ethyl cellulose dissolved in ethyl cellosolve. Thick film resistor was made by screen printing the paste on the alumina substrate and firing it at a suitable temperature. Among thick films made from the resistor paste, the thick film containing 85% SnO and fired at $600^{\circ}C$ demonstrated the finest electrical properties showing 10 K ohm in sheet resistance, 110 ppm/$^{\circ}C$ in TCR. In general, TCR of the thick films made from the oxide-mixture paste is good in linearity, therefore it is suggested the oxide-mixture paste is utilized as the negative thermistor.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.252-252
• /
• 2010

AIZTO (Al-In-Sn-ZnO) thin film was deposited on glass substrate at room temperature by facing target sputtering (FTS) system. The FTS system was designed to array two targets facing each other. Two different kinds of targets were installed on FTS system. We used the ITO (In2O3 90wt%, SnO2 10wt%) target and the AZO (ZnO 98wt%, Al2O3 2wt%). AIZTO films were deposited in each of the applied power of the targets. The electrical and structural properties of the as-deposited AIZTO thin films were then examined by hall-effect measurement, and by using atomic force microscope (AFM), X-ray diffractometer (XRD), and energy dispersive x-ray spectroscopy (EDX). The optical property was measured by an UV-VIS spectrometer.