• Journal of Ceramic Processing Research
• /
• v.13 no.spc1
• /
• pp.75-77
• /
• 2012

The AlGaN-based vertical light-emitting diodes (LEDs) on thick GaN epilayer were fabricated by a hydride vapor phase epitaxy with multi sliding boat system. The optical and electrical characteristics of AlGaN-based vertical LEDs were evaluated using a scanning electron microscopy, electroluminescence and I-V measurements. The AlGaN-based vertical LEDs structure has hexagonal symmetry, 500 ㎛ in diameter and above 67 ㎛ in growth thickness. At the room-temperature, the broaded strong peak and relatively high intensity peak were gradually measured at 405 nm with increasing injection current. And a forward operator voltage was measured to be about 7.5 V.

• Journal of Ceramic Processing Research
• /
• v.13 no.spc2
• /
• pp.295-299
• /
• 2012

We investigated the crystal and the optical properties of GaN-based blue light emitting diodes (LEDs) which were simultaneously grown on c-plane (0001) and semipolar (11-22) GaN templates by using metal-organic chemical vapor deposition (MOCVD). The X-ray rocking curves (XRCs) full width at half maximums (FWHMs) of c-plane (0001) and semipolar (11-22) GaN templates were 275 and 889 arcsec, respectively. In addition, high-resolution X-ray ω-2θ scan showed that satellite peaks of semipolar (11-22) InGaN quantum-wells (QWs) was weaker and broader than that of c-plane (0001) InGaN QWs, indicating that the interface quality of c-plane (0001) QWs was superior to that of semipolar (11-22) QWs. Photoluminescence (PL) and electroluminescence (EL) results showed that the emission intensity and the FWHMs of polar c-plane (0001) LED were much higher and narrower than those of semipolar (11-22) LED, respectively. From these results, we believed that relative poor crystal quality of semipolar (11-22) GaN template might give rise to the poor interfacial quality of QWs, resulting in lower output power than conventional c-plane (0001) GaN-based LEDs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.50-50
• /
• 2008

ZnO has been extensively studied for optoelectronic applications such as blue and ultraviolet (UV) light emitters and detectors, because it has a wide band gap (3.37 eV) anda large exciton binding energy of ~60 meV over GaN (~26 meV). However, the fabrication of the light emitting devices using ZnO homojunctions is suffered from the lack of reproducibility of the p-type ZnO with high hall concentration and mobility. Thus, the ZnO-based p-n heterojunction light emitting diode (LED) using p-Si and p-GaN would be expected to exhibit stable device performance compared to the homojunction LED. The n-ZnO/p-GaN heterostructure is a good candidate for ZnO-based heterojunction LEDs because of their similar physical properties and the reproducibleavailability of p-type GaN. Especially, the reduced lattice mismatch (~1.8 %) and similar crystal structure result in the advantage of acquiring high performance LED devices with low defect density. However, the electroluminescence (EL) of the device using n-ZnO/p-GaN heterojunctions shows the blue and greenish emissions, which are attributed to the emission from the p-GaN and deep-level defects. In this work, the n-ZnO:Ga/p-GaN:Mg heterojunction light emitting diodes (LEDs) were fabricated at different growth temperatures and carrier concentrations in the n-type region. The effects of the growth temperature and carrier concentration on the electrical and emission properties were investigated. The I-V and the EL results showed that the device performance of the heterostructure LEDs, such as turn-on voltage and true ultraviolet emission, developed through the insertion of a thin intrinsic layer between n-ZnO:Ga and p-GaN:Mg. This observation was attributed to a lowering of the energy barriers for the supply of electrons and holes into intrinsic ZnO, and recombination in the intrinsic ZnO with the absence of deep level emission.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.6
• /
• pp.79-91
• /
• 1998

Design principles for high-brightness ligh-temitting diodes have been derived by using escape cone concepts. Based on the design principles, some important high-brightness LED structures developed thus far have been reviewed and, in addition, their external coupling efficiencies have also been estimated. In AlGaAs or InGaAIP LEDs, in which photon absorption in the ohmic electrodes is known to be serious, photon shielding by the electrodes is minimized by using window layer (WL) as well as transparent substrate (TS) leading to significantly improved light-emitting efficiency. However, in InGaN LEDs emitting blue to green lights, the photon absorption in ohmic contact to wide bandgap GaN may be negligible and therefore, photon shielding by the electrodes would not lead to as significant problems as in conventional In AIGaAs or InGaAIP LEDs.

• Proceedings of the Optical Society of Korea Conference
• /
• 2007.07a
• /
• pp.285-286
• /
• 2007

Current distributions according to electrode patterns in vertical structured InGaN/GaN LED (light emitting diode) were investigated quantitatively by utilizing three dimensional electrical circuit modeling method. The uniformity of the injected current density in the active layer was compared among different electrode patterns. It was found that the current uniformity was greatly dependent on the electrode pattern in vertical InGaN/GaN LEDs.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.8
• /
• pp.775-779
• /
• 2006

In this study, sputtered $Al_2O_3$ thin films were evaluated as a passivation layer in the process of InGaN-based blue LEDs in order to improve the brightness of LED lamps. In terms of packaged LED lamps, lamps with $Al_2O_3$ passivation layer emanated higher brightness than those with $SiO_2$ passivation layer, and LED lamps with 90 nm $Al_2O_3$ passivation layer were the brightest among four kinds of lamps. Although lamps with $Al_2O_3$ passivation had a slight increase in operating voltage, their brightness was improved about 13.6 % compare to the lamps made of conventional LEDs without the changes of emitting wavelength.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.244.1-244.1
• /
• 2013

The p-type GaN which act as a hole injection layer in GaN-based LEDs has fundamental problems. The first one arises from the difficulty in growing a highly doped p-GaN (with a carrier concentration exceeding ~1018 $cm^{-3}$). And the second one is the absence of appropriate metals or conducting oxides having a work function that is larger than that of p-type GaN (7.5 eV). Moreover, the LED efficiency is decreases gradually as the injection current increases (the so-called 'efficiency droop' phenomenon). The efficiency droop phenomenon in InGaN quantum wells (QWs) has been a large obstacle that has hindered high-efficiency operation at high current density. In this study, we introduce the new approaches to improve the light-output power of LEDs by using graphene oxide sheets. Graphene oxide has many functional groups such as the oxygen epoxide, the hydroxyl, and the carboxyl groups. Due to nature of such functional groups, graphene oxide possess a lot of hole carriers. If graphene oxide combine with LED top surface, graphene oxide may supply hole carriers to p-type GaN layer which has relatively low free carrier concentration less than electron concentration in n-type GaN layer. To prove the enhancement factor of graphene oxide coated LEDs, we have investigated electrical and optical properties by using ultra-violet photo-excited spectroscopy, confocal scanning electroluminescence microscopy.

• Korean Journal of Materials Research
• /
• v.23 no.3
• /
• pp.161-167
• /
• 2013

The ZnO thin films were grown on GaN template substrates by RF magnetron sputtering at different RF powers and n-ZnO/p-GaN heterojunction LEDs were fabricated to investigate the effect of the RF power on the characteristics of the n-ZnO/p-GaN LEDs. For the growth of the ZnO thin films, the substrate temperature was kept constant at $200^{\circ}C$ and the RF power was varied within the range of 200 to 500W at different growth times to deposit films of 100 nm thick. The electrical, optical and structural properties of ZnO thin films were investigated by ellipsometry, X-ray diffraction (XRD), atomic force microscopy (AFM), photoluminescence (PL) and by assessing the Hall effect. The characteristics of the n-ZnO/p-GaN LEDs were evaluated by current-voltage (I-V) and electroluminescence (EL) measurements. ZnO thin films were grown with a preferred c-axis orientation along the (0002) plane. The XRD peaks shifted to low angles and the surface roughness became non-uniform with an increase in the RF power. Also, the PL emission peak was red-shifted. The carrier density and the mobility decreased with the RF power. For the n-ZnO/p-GaN LED, the forward current at 20 V decreased and the threshold voltage increased with the RF power. The EL emission peak was observed at approximately 435 nm and the luminescence intensity decreased. Consequently, the crystallinity of the ZnO thin films grown with RF sputtering powers were improved. However, excess Zn affected the structural, electrical and optical properties of the ZnO thin films when the optimal RF power was exceeded. This excess RF power will degrade the characteristics of light emitting devices.

• Proceedings of the Optical Society of Korea Conference
• /
• 2001.02a
• /
• pp.48-49
• /
• 2001

GaN는 wurzite structure를 갖는 wide bandgap III-V족 반도체로서, 청색 반도체 laser diode (LD), light emitting diode (LED)등으로 응용되는 물질이다. InGaN quantum well은 GaN계의 청색 LD, LED 구조에서 활성층으로 사용되기 때문에 이에 대한 광학적 연구가 활발하다. InGaN는 GaN위에 성장하면 strain에 의해 piezoelectric 효과가 크게 나타나는 것으로 알려져 있다. 이러한 piezoelectric potential에 의해 외부에서 voltage가 가해지지 않은 상황에서도 InGaN quantum well내의 electron, hole의 wave function이 비대칭 potential의 영향을 받게된다. (중략)

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.17.1-17.1
• /
• 2011

Inorganic III-V light emitting diodes (LEDs) have superior characteristics, such as long-term stability, high efficiency, and strong brightness compared to conventional incandescent lamps and OLED. However, due to the brittle property of bulk inorganic semiconductor materials, III-V LED limits its applications in the field of high performance flexible electronics. This seminar introduces the first flexible and implantable GaN LED on plastic substrates that is transferred from bulk GaN on Si substrates. The superb properties of the flexible GaN thin film in terms of its wide band gap and high efficiency enable the dramatic extension of not only consumer electronic applications but also the biosensing scale. The flexible white LEDs are demonstrated for the feasibility of using a white light source for future flexible BLU devices. Finally a water-resist and a biocompatible PTFE-coated flexible LED biosensor can detect PSA at a detection limit of 1 ng/mL. These results show that the nitride-based flexible LED can be used as a type of implantable LED biosensor and as a therapy tool.