• Journal of the Korean Institute of Intelligent Systems
• /
• v.18 no.6
• /
• pp.775-780
• /
• 2008

In this paper, unmanned driving of robotic vehicle using magnetic marker is proposed. One of the most important component of autonomous vehicle is to detect the position of a magnetic marker on the road. In order to calculate the precise position of a magnet embedded on the road, the relation of magnetic field and a sensor is analyzed, and a new position sensing system using arrayed magnetic sensor is proposed. Also, the steering control system using a stepping motor is developed for driving by automatic mode as well as manual mode. For the verification of usability, the developed robotic vehicle is tested on magnetic road.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.8
• /
• pp.719-724
• /
• 2012

A traffic detection system is a device that collects traffic information around an intersection. Most existing traffic detection systems provide very limited traffic information for signal control due to the restriction of vehicle detection area. A signal control scheme determines the transition among signal phases and the time that a phase lasts for. However, the existing signal control scheme do not resolve the traffic congestion effectively since they use restricted traffic information. In this paper, a new traffic detection system with a zone division signal control scheme is proposed to provide correct and detail traffic information and decrease the vehicle's waiting time at the intersection. The traffic detection system obtains traffic information in a way of vehicle-to-roadside communication between vehicles and sensor network. A new signal control scheme is built to exploit the sufficient traffic information provided by the proposed traffic detection system efficiently. Simulation results show that the proposed signal control scheme has 121 % and 56 % lower waiting time and delay time of vehicles at an intersection than other fuzzy signal control scheme.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.11
• /
• pp.2471-2477
• /
• 2010

lately, vehicle blackbox increasing importance and usability Is needed accuracy and variety of information. because, blackbox help to analyze the exact cause of the accident and use as objective evidence in vehicle-related crime. In the paper, to overcome the limitations of the existing black box, use various sensors and vehicle information blackbox store current state of the vehicle with OBD-II protocol using vehicle state information and store exact current location and direction information of the vehicle with Gyro sensor and GPS and use global time of GPS for synchronization of information. In addition, blackbox back the information up with wifi. because, when blackbox damaged, dirvers were able to verify the information.

• The Journal of Korea Robotics Society
• /
• v.18 no.1
• /
• pp.93-98
• /
• 2023

In this paper, the development of an autonomous electric vehicle for logistics with a robotic arm is introduced. The manual driving electric vehicle was converted into an electric vehicle platform capable of autonomous driving. For autonomous driving, an encoder is installed on the driving wheels, and an electronic power steering system is applied for automatic steering. The electric vehicle is equipped with a lidar sensor, a depth camera, and an ultrasonic sensor to recognize the surrounding environment, create a map, and recognize the vehicle location. The odometry was calculated using the bicycle motion model, and the map was created using the SLAM algorithm. To estimate the location of the platform based on the generated map, AMCL algorithm using Lidar was applied. A user interface was developed to create and modify a waypoint in order to move a predetermined place according to the logistics process. An A-star-based global path was generated to move to the destination, and a DWA-based local path was generated to trace the global path. The autonomous electric vehicle developed in this paper was tested and its utility was verified in a warehouse.

• Journal of Navigation and Port Research
• /
• v.35 no.2
• /
• pp.121-130
• /
• 2011

The localization of vehicle is an important part of an unmanned vehicle control problem. Pseudolite ultrasonic system(PUS) is the method to find an absolute position with a high accuracy by using ultrasonic sensor. And Gyro is the inertial sensor to measure yaw angle of vehicle. PUS can be able to estimate the position of mobile robot precisely, in which errors are not accumulated. And Gyro is a more faster measure method than PUS. In this paper, we suggest a more accuracy method of calculating PUS which is numerical analysis approach named Newtonian method. And also propose the fusion method to increase the accuracy of estimated angle on moving vehicle by using PUS and Gyro integrated system by Kalman filtering. To control the 4WS unmanned vehicle, the trajectory following algorithm is suggested. And the new concept arbitration of goal controller is suggested. This method considers the desirability function of vehicle state. Finally, the performances of Newtonian method and designed controller were verified from the experimental results with the 4WS vehicle scaled 1/10.

• Journal of Auto-vehicle Safety Association
• /
• v.4 no.2
• /
• pp.32-36
• /
• 2012

The Automatic unmanned target object carrying system (AUTOCS) is developed for testing road vehicle radar and vision sensor. It is important for the target to reflect the realistic target characteristics when developing ASV or ADAS products. The AUTOCS is developed to move the pedestrian or motorcycle target for desired speed and position. The AUTOCS is designed that only payload target which is a manikin or a motorcycle is detected by the sensor not the AUTOCS itself. In order for the AUTOCS to have low exposure to radar, the AUTOCS is stealthy shaped to have low RCS(Radar Cross Section). For deceiving vision sensor, the AUTOCS has a specially designed pattern on outside skin which resembles the asphalt pattern. The AUTOCS has three driving modes which are remote control, path following and replay. The AUTOCS V.1 is tested to verify the radar detect characteristics, and the AUTOCS successfully demonstrated that it is not detected by a car radar. The result is presented in this paper.

• Journal of the Korean Institute of Gas
• /
• v.14 no.4
• /
• pp.56-62
• /
• 2010

The purpose of this paper analyzes and investigates the failure case studies of electronic control sensors for a LP gas engine. The malfunction of crank angle sensor, which controls a fuel injection volume of LP gas, displays an irregular and non-uniform pulse wave form. The pulse form, which is related to the noise of the crank angle sensor, displays at the rectangular peak with a saw-toothed shape and is intermittently generated with a level of 2.46V noise signal. The malfunction of No. 1 TDC sensor in which is caused from the internal disorder affects to the reduction of engine power and engine stop suddenly. If the malfunction of oxygen sensor is occurred due to a wiring problem of a sensor connector, the LP gas vehicle may produce a shaking and disharmony of an engine because of no signal supply from the oxygen sensor. The air cleaner replica produces the clogging of continuous supply of fresh air. This may cause the retardation of vehicle acceleration and engine disharmony intermittently.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.6
• /
• pp.81-87
• /
• 2023

SAE J2601 and SAE J2799, the communication protocols between a hydrogen refueling station and a fuel cell electric vehicle, only cover hydrogen charging. In this paper, we measure the hydrogen detection, current, and voltage of a fuel cell electric vehicle and transmit the sensor data to the hydrogen refueling station by changing the WiFi protocol. A small-scale laboratory model was built using Raspberry Pi for sensing, controlling, and transmitting sensor data of a fuel cell electric vehicle. The sensor data was stored in the database of the hydrogen refueling station, and a dashboard was configured using Grafana to analyze the stored data. When hydrogen is detected, the dispenser valve of the hydrogen refueling station is locked. Then, we measured the average transmission delay according to the WiFi protocol. The results showed that IEEE 802.11a is the most suitable WiFi protocol for transmitting sensor data between the hydrogen refueling station and the fuel cell electric vehicle.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.866-867
• /
• 2011

As part of the green growth, The Green Car has attracted wide attention. Types of the Green Car are Electric Vehicle, Plug-in Hybrid Electric Vehicle, Hybrid Electric Vehicle, Fuel Cell Vehicle and Clean Diesel Vehicle. Of these, The electric vehicle is equipped with the BDU(Battery Disconnecting Unit). BDU is supplying stable battery power and blocking it to protect electrical system of the electric vehicle. The BDU consists of electric components such as current sensor, fuse and pre-charge resistor. These must pass Voltage withstand test, Salt mist test, Thermal shock test, Vibration test and Short-circuit test commonly to verify reliability of the electric components. In addition, The current sensor should be verified whether normal operation. The breaking capacity of fuse should be verified. The durability of pre-charge resistor should be verified by supplying battery power and blocking it repeatedly. The reliability of BDU as well as the electric vehicle is secured by verifying the reliability of electric components. In addition, It will contribute to the acceleration and promotion of Green Car Technology.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.38 no.6
• /
• pp.783-791
• /
• 2018

The biased estimation of low density rainfall network and radar rainfall has limited application to extreme rainfall in a small area. To improve this, more rainfall information needs to be produced. In this study, we analyzed the applicability of the vehicle rainfall sensor developed and used recently. The developed rainfall sensor was attached to the vehicle to observe the rainfall according to the movement of the vehicle. The analytical method used time series and average rainfall values for observations of rainfall sensors and nearby rainfall stations. The results show that the trend of observed values according to rainfall events shows a certain pattern. It is analyzed that it is caused by various causes such as the difference between the observation position of the rainfall sensor and the nearby rainfall station, the moving speed of the vehicle, and the rainfall observation method. This result shows the possibility of rainfall observation using a rainfall sensor for a vehicle, and it is possible to observe rainfall more precisely through experiments and improvement of rainfall sensors in various conditions in the future.