• 한국전기전자재료학회논문지
• /
• 제16권2호
• /
• pp.89-96
• /
• 2003

Photoluminescence (PL) and photoluminescence excitation (PLE) spectroscopy have been performed at 6 K on the 1540 nm $^4$I$\_$(13/2)/\longrightarrow$^4$I$\_$(15/2)/ emission of Er$\^$+3/ in in situ Er-doped GaN The PL and PLE spectra of in situ Er-doped GaN are compared with those of Er-implanted GaN in this study. The lineshapes of the broad PLE absorption bands and the broad PL bands in the spectra of the in situ Er-doped GaN are similar to those in Er-doped glass rather than in the Er-implanted GaN. The PL spectra of this in situ Er-doped GaN are independent of excitation wavelength and their features are significantly different from the site-selective PL spectra of the Er-implanted GaN. These PL and PLE studies reveal that a single type of Er$\^$3+/ sites is present in the in situ Er-doped GaN and these Er sites are different from those observed in the Er-implanted GaN. In addition, the comparison of the PL single strength illustrates that the excitation of Er$\^$3+/ sites through the energy absorption of defects in Er-implanted GaN.

• Fisheries and Aquatic Sciences
• /
• 제11권2호
• /
• pp.103-112
• /
• 2008

Compressional sound velocities of shelf sediments in the South Sea of Korea, were measured in situ and in the laboratory for six cores. In situ sound velocity was measured using the Acoustic Lance (frequency of 7.5-15 kHz), while laboratory velocity was measured by the pulse transmission technique (frequency of 1MHz). Physical properties were relatively uniform with sediment depth, suggesting little effect of sediment compaction and/or consolidation. Average in situ velocity at each core site ranged from 1,457 to 1,488 m/s, which was less than the laboratory velocity of 1,503 and 1,604m/s. In muddy sediments the laboratory velocity was 39-47 m/s higher than in situ velocity. In sandy sediments, the difference was greater by an average of 116 m/s. Although the velocity data were corrected by the velocity ratio method based on bottom water temperature, the laboratory velocity was still higher than the in situ velocity (11-21 m/s in muddy sediments and 91 m/s in sandy sediments). This discrepancy may be caused by sediment disturbance during core collection and/or by the pressure of Acoustic Lance insertion, but it was most likely due to the frequency difference between in situ and laboratory measurement systems. Thus, when correcting laboratory velocity to in situ velocity, it is important to consider both temperature and frequency.

• 대한의생명과학회지
• /
• 제2권2호
• /
• pp.257-265
• /
• 1996

토끼 바이러스성 출혈증의 원인체를 실험 토끼에 접종하여 증식을 유도하고 간장에서 hematoxylin & eosin 염 색 에서 조직학적 진단과 세포내 viral RNA의 소재를 결정하기 위해 post-unicryl 포매한 block의 절편을 사용하여 단 염색과 전자현미경적 in situ hybridization을 시도하였다. 토끼 출혈증 viral RNA의 보합 결합에 이용하는 probe는 4717에서 4800(84bases)까지 oligonucleotide를 5'말단에 biotin-CE phosphoramidite로 표지하여 사용하였다. 보합결합물의 증명은 신호 표지로서 antibiotin antibody-l0nm gold를 사용하였으며, hybridization이나 증명은 기존 protocol에서 약간의 변법을 사용하였다. 0.02% glutaraldehyde에서 고정하고 unicryl resin 포매한 표본, biotinylated oligonucleotide probe, antibiotin antibody-l0nm gold로 실험한 결과 증강된 신호를 얻을 수 있었다. 특히 전처리를 생략하므로써 실험 과정을 간단하게 하여 신속한 결과를 얻을 수가 있었다. 전자현미경 in situ hybridization을 통하여 토끼 출혈증 바이러스의 주요 표적은 간세포로 감염 세포의 세포질 내 미토콘드리아와 핵 사이에서 immune gold입자가 뚜렷하게 표지 됨으로서 viral RNA를 증명할 수 있었다.

• 미생물학회지
• /
• 제40권2호
• /
• pp.167-171
• /
• 2004

효과적인 원위치 중합효소 연쇄반응 (In situ PCR)을 위해서는 증폭된 PCR 산물의 세포외 유출을 감소시켜야 한다. 이를 위한 한 방법으로 거대분자 PCR 산물을 합성시키기 위한 5'쪽에 서로 상보적인 꼬리서열을 가진 프라이머(꼬리 프라이머; tailed primer)가 사용되었으나 많은 PCR 횟수로 인해 시간의 낭비와 세포조직의 형태보존성이 저하되는 문제가 발생하였다. 따라서 PCR 조건을 가능한 최적화시키고, 최소의 PCR 횟수로써 세포외 유출을 막을 수 없는 방법이 필요하게 되었다. 이러한 방법의 일환으로 꼬리 프라이머를 이용하여 PCR 튜브 속에서 목표 핵산없이 프라이머 중합체(primer polymers)의 형성을 유도하였고, 이를 유리 슬라이드위에 고정시킨 Molt/LAV 세포들에 처리하여 20 회의 짧은 시간에서도 적절한 탐침을 할 수 있게 되었다. 이로 인해 프라이머 중합체의 원위치 중합효소 연쇄반응에서의 사용가능성을 타진하였다.

• Tribology and Lubricants
• /
• 제31권6호
• /
• pp.239-244
• /
• 2015

Chemical mechanical polishing (CMP) is one of the most important processes for enabling sub-14 nm semiconductor manufacturing. Moreover, post-CMP defect control is a key process parameter for the purpose of yield enhancement and device reliability. Due to the complexity of device with sub-14 nm node structure, CMP-induced defects need to be fixed in the CMP in-situ cleaning module instead of during post ex-situ wet cleaning. Therefore, post-CMP in-situ cleaning optimization and cleaning efficiency improvement play a pivotal role in post-CMP defect control. CMP in-situ cleaning module normally consists of megasonic and brush scrubber processes. And there has been an increasing effort for the optimization of cleaning chemistry and brush scrubber cleaning in the CMP cleaning module. Although there have been many studies conducted on improving particle removal efficiency by brush cleaning, these studies do not consider the effects of brush contamination. Depending on the process condition and brush condition, brush cross contamination effects significantly influence post-CMP cleaning defects. This study investigates brush cross contamination effects in the CMP in-situ cleaning module by conducting experiments using 300mm tetraethyl orthosilicate (TEOS) blanket wafers. This study also explores brush pre-treatment in the CMP tool and proposes recipe effects, and critical process parameters for optimized CMP in-situ cleaning process through experimental results.

• 대한금속재료학회지
• /
• 제48권7호
• /
• pp.683-689
• /
• 2010

In this study, FeAl based intermetallic matrix composites reinforced with in-situ synthesized TiC particles were fabricated by an in-situ liquid mixing process. The microstructures, mechanical properties and fracture behaviors of the in-situ liquid mixing processed composite were investigated and compared with the vacuum suction casting processed composite. The results showed that the in-situ formed TiC particles exhibited fine and uniform dispersion in the liquid mixing processed composite, while significant grain boundary clustering and coarsening of TiC particles were obtained by the vacuum suction process. It was also shown in both types of composites that the hardness and bending strength were increased with the increase of the TiC volume fractions. Through the study of fractography in the bending test, it was considered that the TiC particles prohibited brittle intergranular fracture of FeAl intermetallic matrix by crack deflections. Because of the uniformly distributed fine TiC particles, the bending strength of the liquid mixing processed composite was superior to that of the casting processed composite.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1998년도 가을 학술발표회 논문집
• /
• pp.81-88
• /
• 1998

• Applied Microscopy
• /
• 제43권2호
• /
• pp.88-97
• /
• 2013

Technical investigation to figure out the problems arising during in-situ heating electron backscatter diffraction (EBSD) analysis inside scanning electron microscopy (SEM) was carried out. EBSD patterns were successfully acquired up to $830^{\circ}C$ without degradation of EBSD pattern quality in steels. Several technical problems such as image drift and surface microstructure pinning were taking place during in-situ experiments. Image drift problem was successfully prevented in constant current supplying mode. It was revealed that the surface pinning problem was resulted from the $TiO_2$ oxide particle formation during heating inside SEM chamber. Surface pinning phenomenon was fairly reduced by additional platinum and carbon multi-layer coating before in-situ heating experiment, furthermore was perfectly prevented by improvement of vacuum level of SEM chamber via leakage control. Plane view in-situ observation provides better understanding on the overall feature of recrystallization phenomena and cross sectional in-situ observation provides clearer understanding on the recrystallization mechanism.

• Transactions on Electrical and Electronic Materials
• /
• 제6권3호
• /
• pp.106-109
• /
• 2005

We have investigated the generation of pretilt angle for a nematic liquid crystal (NLC) alignment with in-situ photoalignment method on polyimide (PI) surfaces using polymer films. Especially, we studied in-situ photoalignment changing heating temperature from $50^{\circ}C\;to\;120^{\circ}C$ on the polymer film. The LC aligning capabilities and pretilt angle on the polymer substrates were better than those on the glass substrate using in-situ photoalignment method. It is considered that this increase in pretilt angle may be attributed to the roughness of the micro-groove substrate induced by the in-situ photoalignment. As temperature of heated subtrate and UV exposure time increase, pretilt angle of the cell used polymer film increased. It is considered that the heating temperature of substrate is attributed to generate pretilt angle. Also, electro-optical performances of the in-situ photoaligned TN cell using the polymer substrate are almost the same as that of the TN cell using the glass substrate.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 추계 학술논문 발표대회
• /
• pp.42-43
• /
• 2019

In-situ production of PC (precast concrete) members can reduce costs by about 14.5% -21.6% compared to in-plant production due to the reduction of transportation costs, factory profits and overhead costs. However, in-situ production of PC members presents a variety of risks, including member production and yard area securing, and lead time for production within the installation period. To solve this, it is necessary be able to analyze and control and monitor the risk factors that influence in-situ production for PC member. The purpose of this study is to develop a dynamic simulation model for in-situ production and erection integrated management for PC members. For this study, risk factor identification, causal loop diagram, and dynamic simulation model construction were performed sequentially. The results of this study will be used as a basis for developing a risk management model for PC in-situ production.