• 한국자동차공학회논문집
• /
• 제4권2호
• /
• pp.173-182
• /
• 1996

An analytical model has been developed to predict the elastic properties of a filled resin reinforced by chopped fibers, a three-phase composite such as a filled sheet molding compound(SMC). In the model the matrix material and fillers form an effective matrix. The effective matrix is then considered to be reinforced with long fibers lying in the sheet plane but randomly oriented in the plane. Expressions for the resulting transversely isotropic composite properties are explicitly presented. Using this model, the Young's and shear moduli are calculated for the SMC sample with filler weight fraction of 35% and fiber content of 30%. The same properties are also determined experimentally. The agreement between the calculated and measured elastic moduli is found to be very good for the in-plane properties. However, the out-of-plane properties show a large difference because the effect of voids is not taken into account in the model.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 추계학술발표대회 논문집
• /
• pp.74-78
• /
• 2001

In this study, out-of-plane properties and CTEs were predicted for 8-harness satin weave textile composites. The properties were calculated by unit cell analysis for configurations with varied waviness ratio and phase shifts. Macro elements were employed to reduce the computer resource requirement. It was found that the out-of-plane properties and CTEs were varied as the phase shift changed. However the dependency was much weaker than the in-plane properties.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.314.1-314.1
• /
• 2014

The properties of Ni/Au Ohmic contacts formed on nonpolar a-plane GaN grown on r-plane sapphire substrate with different tilt angles are investigated using current-voltage (I-V) measurements. To investigate the effects of pattern direction and size on Ohmic contact properties of a-plane GaN, transmission line method (TLM) patterns are formed either along c-axis and m-axis on nonpolar GaN surface with different size. I-V measurement results show that the size of TLM pattern and formation direction of electrode have an effect on the electrical properties of a-plane GaN. The large sized patterns show the relatively lower sheet resistance compared to the small sized patterns. In addition, the sheet resistance of a-plane GaN along m-axis shows lower values than that along the c-axis. Finally, the effects of miscut angle of r-sapphire substrate ($0.2^{\circ}$, 0.4oand $0.6^{\circ}$) on electrical properties of a-plane GaN will be discussed.

• 호남수학학술지
• /
• 제19권1호
• /
• pp.107-116
• /
• 1997

In this paper, we get some properties of curves of constant relative breadth in the Minkowski plane.

• 한국산학기술학회논문지
• /
• 제16권4호
• /
• pp.2407-2414
• /
• 2015

본 논문은 적층된 복합재 라미네이트의 두께방향(out-of-plane) 열탄성 물성치 계산식에 관하여 서술하였다. 다양한 적층패턴을 유도된 계산식에 적용한 결과, 섬유방향이 단방향 0도로 구성된 라미네이트에서 총 플라이수 중 10% 이상이 모두 90도 섬유방향으로 이루어져 있거나, 또는 15도 이상의 섬유방향으로 형성된 적층패턴을 가지는 라미네이트(Laminate)의 두께방향 물성치를 복합재 라미나(lamina)의 단섬유방향과 직교하는 물성치(transverse property)로 가정하는 것은 적절하지 않은 것으로 나타났다.

• 대한기계학회논문집
• /
• 제17권11호
• /
• pp.2676-2683
• /
• 1993

Plane strain punch stretching test(PSST) was performed for various automotive steel sheets. To clarify the effect of tensile properties on plane strain stretchability, the limiting punch height(LPH) values were obtained in plane strain punch stretching test and related to the tensile properties of the materials. The results show that the total elongation El and work hardening exponent n compared to other parameters obtained from tensile test well correlate with the LPH value. In comparision with the Erichsen test and LDH test the PSST can be statistically used as an alternative in assessing the stamping formability of automotive steel sheets with the advantages of good reproducibility and easy testing method.

• Structural Engineering and Mechanics
• /
• 제58권4호
• /
• pp.731-743
• /
• 2016

Plastic behaviors, based on the von Mises yield criterion, of circular discs containing a purely elastic, circular inclusion under uniform temperature loading are studied with the finite element analysis. Temperature-dependent mechanical properties are considered for the matrix material only. In addition to analyzing the plane stress and plane strain disc, a 3D thin disc and cylinder are also analyzed to compare the plane problems. We determined the elastic irreversible temperature and global plastic collapse temperature by the finite element calculations for the plane and 3D problem. In addition to the global plastic collapse, for the elastically hard case, the plane stress problem and 3D thin disc may exhibit a local plastic collapse, i.e. significant pile up along the thickness direction, near the inclusion-matrix interface. The pileup cannot be correctly modeled by the plane stress analysis. Furthermore, due to numerical difficulties originated from large deformation, only the lower bound of global plastic collapse temperature of the plane stress problem can be identified. Without considerations of temperature-dependent mechanical properties, the von Mises stress in the matrix would be largely overestimated.

• 한국수학교육학회지시리즈B:순수및응용수학
• /
• 제28권1호
• /
• pp.71-89
• /
• 2021

We define the constant ratio curves in the isotropic plane and investigate their deflection properties.

• Structural Engineering and Mechanics
• /
• 제43권6호
• /
• pp.739-759
• /
• 2012

The tailoring optimization technique recently developed by the author for improving structural response and energy absorption of composites is extended to sandwich shells using a previously developed zig-zag shell model with hierarchic representation of displacements. The in-plane variation of the stiffness properties of plies and the through-the thickness variation of the core properties are determined solving the Euler-Lagrange equations of an extremal problem in which the strain energy due to out-of-plane strains and stresses is minimised, while that due to their in-plane counterparts is maximised. In this way, the energy stored by unwanted out-of-plane modes involving weak properties is transferred to acceptable in-plane modes. As shown by the numerical applications, the critical interlaminar stress concentrations at the interfaces with the core are consistently reduced without any bending stiffness loss and the strength to debonding of faces from the core is improved. The structural model was recently developed by the author to accurately describe strain energy and interlaminar stresses from the constitutive equations. It a priori fulfills the displacement and stress contact conditions at the interfaces, considers a second order expansion of Lame's coefficients and a hierarchic representation that adapts to the variation of solutions. Its functional d.o.f. are the traditional mid-plane displacements and the shear rotations, so refinement implies no increase of the number of functional d.o.f. Sandwich shells are represented as multilayered shells made of layers with different thickness and material properties, the core being treated as a thick intermediate layer.

• 한국멀티미디어학회논문지
• /
• 제25권7호
• /
• pp.912-921
• /
• 2022

Autonomous vehicles equipped with cameras, such as robots, fork lifts, or cars, can be found frequently in industry sites or usual life. Those cameras show planar motion because the vehicles usually move on a plane. Sometimes the cameras in fork lifts moves vertically. The cameras under planar and vertical motion provides useful properties for horizontal or vertical lines that can be found easily and frequently in our daily life. In this paper, some useful back-projection properties are suggested, which can be applied to horizontal or vertical line images captured by a camera under planar and vertical motion. The line images are back-projected onto a virtual plane that is parallel to the planar motion plane and has the same orientation at the camera coordinate system regardless of camera motion. The back-projected lines on the virtual plane provide useful information for the world lines corresponding to the back-projected lines, such as line direction, angle between two horizontal lines, length ratio of two horizontal lines, and vertical line direction. Through experiments with simple plane polygons, we found that the back-projection properties were useful for estimating correctly the direction and the angle for horizontal and vertical lines.