• 건설안전기술
• /
• 통권50호
• /
• pp.71-79
• /
• 2009

Construction companies economic to lighten the restrictions on safety education and training due to the domestic recession as long as the global downturn. With this, the Korean government restrictions, but the incidents are being sharply increased nowadays. The construction industry hazardous than any others, so, they insist to reinforce the training for incidents prevention, to be disregarded at the subcontractors of the bigger construction companies problems. According to these matters, this study hereby surveyed regarding their suggestions for the improvements of the training concepts through questionnaires below.

• 대한전자공학회논문지
• /
• 제27권6호
• /
• pp.895-900
• /
• 1990

With the MOS device scailing down, the substrate concentration must increase in order to avoid punchthrough leakage current due to the DIBL(Drain Induced Barrier Lowering) effect. However the enhancement of the substrate concentration increases source, drain juntion capacitances and substrate current due to hot elelctron, degrading the speed characteristics and reliability of the MOS devices. In this paper, a new device, called CODE(Channel Only Dopant Enhancement) MOS, an its fabrication are proposed. By comparing the fabricated CODE MOSFET with the conventional device, the improvements on DIBL, substrate current and source, drain juntion capacitances are realized.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1999년도 추계종합학술대회 논문집
• /
• pp.879-882
• /
• 1999

The effects of the substrate bias on the performance of programming erasing in p-channel flash memory cell have been investigated. It is found that applying positive substrate bias can improve the programming and erasing speed. This improvements can be explained by Substrate Current Induced Hot Electron Injection. From the results, we can confirm that BTB programming method is better in programming and erasing speed than CHE programming method.

• Archives of Pharmacal Research
• /
• 제2권1호
• /
• pp.71-78
• /
• 1979

Since the introduction of aspirin as a therapeutic agent in 1899, there have been numerous attempts at the improvement of its therapeutic value through molecular modification. These endeavors have centered mainly around the following two approaches : (a) improvement of the potency by introduction of a suitable group or groups on the benzene ring; and (b) modification of the carboxylic acid group, which is thought to be an immediate cause of the irritant effect.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2008년도 추계학술대회 논문집
• /
• pp.166-168
• /
• 2008

This paper presents a vector control of Linear Induction Motor(LIM) based on a slip frequency control. And a Linear Induction Motor modeling included the end effect using circuit and equation method is also presented. We demonstrated through simulation the improvements achieved by the proposed scheme.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 추계학술대회 논문집
• /
• pp.302-309
• /
• 2008

This paper presents a vector control of Linear Induction Motor base on a slip frequency control. And a linear induction motor modeling included the end effect using circuit and equation method is also proposed. We demonstrated through simulation the improvements achieved by the proposed scheme.

• 한국세라믹학회지
• /
• 제29권4호
• /
• pp.298-304
• /
• 1992

Flexural strength, microstructure, hydration reaction and moisture sensitivity in macro defect-free (MDF) cement, which basically prepared of high alumina cement (HAC) and hydroxypropyl methylcellulose (HPMC) and polyvinylalcohol (PVA) as water soluble polymer were investigated. Cement composites based on HAC-PVA system were improved in flexural strength than that of HAC-HPMC system especially, the strength of specimens added to 10 wt% of polyvinylalcohol was 160 MPa. These improvements of flexural strength were attributed to not only the effect of water soluble polymer in elimination of macropores (above 100 $\mu\textrm{m}$) and cement grain bridging, but the effect of unhydrate cement as an aggregate. Moisture sensitivity and flexural strength in wet condition of MDF cement composites immersed in water at 80$^{\circ}C$ for 3 days were decreased.

• 한국유체기계학회 논문집
• /
• 제16권3호
• /
• pp.26-31
• /
• 2013

In present 3D CFD study, the method for determining leakage and rotordynamic coefficients of a plain-gas seal is suggested by using the relative coordinate system for steady-state simulation. In order to find the effect of pre-swirl speed at seal inlet, pre-swirl velocity is included as a parameter. Present analysis is verified by comparison with results acquired from Bulk-flow analysis code and published experimental results. The results of 3D CFD rotordynamic coefficients of direct stiffness(K) and cross-coupled stiffness(k) show improvements in prediction. As pre-swirl speed at seal inlet increases, k also increases to destabilize system. However, pre-swirl speed at seal inlet does not show sensitivity to the leakage and rotordynamic coefficients of K and damping(C).

• 대한기계학회논문집A
• /
• 제26권3호
• /
• pp.461-470
• /
• 2002

The present paper investigates the effect of hot isostatic pressing (HIPing) on mechanical properties, e.g., tensile strength, ductility and impact absorption energy of sand and die casted aluminum alloys. After HIPing at various temperatures and pressure conditions, uniaxial tensile test and Izod impact test of the samples were carried out. The experimental results showed improvements in uniaxial tensile strength, elongation and Izod impact toughness of sand casted aluminum alloy, while deterioration of a tensile strength fur die casted aluminum alloy. The effect of HIPing for microstructure of the cast aluminum alloy was also investigated.

• KSTLE International Journal
• /
• 제3권2호
• /
• pp.79-83
• /
• 2002

Sealing an oil-air mixture plays important roles to have an enhanced lubrication for high speed spindle. High speed spindle requires non-contact type of sealing mechanism. Current work emphases on the investigation of the air jet effect on the protective collar type labyrinth seal. To improve the sealing capability of conventional labyrinth seal, air jet was injected against through the leakage flow, It has a combined geometry of a protective collar type and an air jet type. Both of a numerical analysis by CFD (Computational Fluid Dynamics) and experimental measurements are carried out to verify sealing improvement The sealing effects of the leakage clearance and the air jet magnitude are studied in various parameters. The results of pressure drop in the experiment match reasonably to those of the simulation by introducing a flow coefficient Effect of sealing improvement is explained as decreasing of leakage clearance by air jetting. Thus, sealing effect is improved by amount of air jetting even though clearance becomes larger.