• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2008년도 추계 학술논문 발표대회
• /
• pp.13-16
• /
• 2008

This paper is to present the performance data for improved direct setting method using tile bond for application of porcelain tile under 1 percent absorptance. For this purpose, improved direct setting method type 1 & 2(tile bond curing time 0, 24H) were compared with the conventional setting methods(including direct setting method and improved pressure setting method) in the sight of the adhesive stability of porcelain tile. It tested for tiles after 14, 28days under standard condition and severe conditions. The severe conditions were water immersion, heat ageing(70℃) and freeze-thaw cycle. On the basis of test results, the adhesive strength of direct setting method was lowest for the conventional setting methods. But improved direct setting method using tile bonds(A, B) came close to the result of improved pressure setting method using tile bonds.

• 한국정밀공학회지
• /
• 제28권2호
• /
• pp.202-210
• /
• 2011

The fabrication method of aspheric lens is changed from machining to press molding so as to improve the productivity. In the case of the press molding method, the temperature control of the molding die is most important, because the temperature of each molding die determines the quality of lens. But any practical method for direct measuring of the lens temperature and the die internal temperature is yet unknown. Besides, in the case of the press molding system in which the heating and pressing and cooing of a die is done at separate work stations, the lens productivity of the system for small lens is yet too low. The paper shows an improved structure of convective sequential system, the lens productivity of which is three times as many as the conventional convective system. To know the die internal temperature, numerical results are given using ANSYS. A new convective sequential system is developed and tested. Finally, the Taguchi method is applied in order to optimize the setting conditions of individual work station of the system.

• 한국정밀공학회지
• /
• 제27권12호
• /
• pp.67-74
• /
• 2010

The fabrication method of aspheric lens is changed from machining to press molding so as to improve the productivity. In the case of the press molding method, the temperature control of the molding die is most impotent, because the temperature of each molding die determines the quality of lens. But any practical method for direct measuring of the lens temperature and the die internal temperature is yet unknown. Besides, in the case of the press molding system in which the heating and pressing and cooing of a die is done at one work station, the cycle time for the system is yet too long. The paper shows an improved structure of radiant sequential system in which the heating and pressing and cooing of dies is done at individual work station so as to cut down the cycle time. To know the die internal temperature, numerical results are given using ANSYS. An experimental radiant sequential system is developed and tested. Finally, the Taguchi method is applied in order to optimize the setting conditions of individual work station.

• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.122-129
• /
• 2004

Finite element analysis was performed to analyze structural safety of a new heavy-duty direct injection diesel engine. A half section of the in-line 6-cylinder engine was selected as a computational domain. A mapping method was used to project heat transfer coefficients from CFD results of engine coolant flow onto the FE model. The accurate setting of thermal boundary condition on the FE model was expected to result in improved prediction of temperature, cylinder bore distortion, and stresses. Characteristics of high cycle fatigue were investigated by assuming the engine was operated under the following five loading conditions repeatedly; assembly force, assembly force with thermal loading, alternating maximum gas pressure loading at each cylinder combined with assembly force and thermal loading. Distribution of fatigue safety factor was calculated by using it Haigh diagram in which the maximum and the minimum stresses were selected from the five loading cases.

• 한국CDE학회논문집
• /
• 제17권1호
• /
• pp.35-44
• /
• 2012

Many automobile manufacturers are doing experiment on manufacturing environments by using an augmented reality technology. However, system layout and process simulation by using the virtual reality technology have been performed actively more than by using the augmented reality technology in practical use so far. Existing automobile assembly by using the augmented reality requires the precise calibrating work after setting the robot because the existing augmented reality system for the automobile assembly system configuration does not include the end tip deflection and the robot joints deflection due to the heavy weight of product and gripper. Because the robot is used mostly at the automobile assembly, the deflection problem of the robot joint and the product in the existing augmented reality system need to be improved. Moreover camera lens calibration has to be performed precisely to use augmented reality. In order to improve this problem, this paper introduces a method of the software based calibration to apply the augmented reality effectively to the automobile assembly system. On the other hand, the camera lens calibration module and the direct compensation module of the virtual object displacement for the augmented reality were designed and implemented. Furthermore, the developed automobile assembly system oriented AR-system was verified by the practical test.

• 간호행정학회지
• /
• 제13권3호
• /
• pp.352-361
• /
• 2007

Purpose: The purpose of this study was to develop roles and organizational policy of advanced practice nurses (APNs) in an acute hospital setting. Method: The design of the study was to descriptive-exploratory. Sample consisted of 43 participants who included 13 nurses, 18 nurse managers and 12 physicians. Survey, interview and focus group interview were performed to obtain the data. Results: The expected roles of APNs were education and counseling, direct management patient care with advanced skills, research, and collaboration and coordination among several departments. The expected outcomes were patient satisfaction, improved access to care, decreased the rate of complications, and speedy provision of services. Based on research, a proposal of APNs roles and organizational policy in a hospital setting was developed, which included definition of APNs, qualification, roles and specific roles, specialty areas, accountability, recruitment and affiliation, privileges, and expected outcomes. Conclusion: This study gives a guideline on how to introduce and use APNs in acute care tertiary settings.

• 한국기록관리학회지
• /
• 제1권1호
• /
• pp.37-52
• /
• 2001

1. 중국 당안학의 형성 및 발전 : 수세기에 걸친 당안관리의 역사를 가진 중국에서 초기 당안학이 등장한 것은 1930년대이며, 그 이후 당안사업들이 큰 성과를 거둠으로써 연구가 촉진되었다. 1.1 연구영역의 확장: 국가규모 당안사업의 건립과 발전에 힘입어 연구영역이 확장되었다. 당안관, 당안실, 행정, 교육, 선전, 당안과 기타 문헌정보의 관계, 당안과 인류사회 사이의 폭넓고 심층적인 관계까지 연구하기에 이르렀다. 중국 당안학은 기본 이론, 당안관리의 원칙과 방법, 당안관리체계, 당안학의 구성등 네가지 측면으로 구분할 수 있다. 1.2 풍부한 연구성과 취득: 중국 당안학자들의 노력을 통해 풍부한 연구성과를 거두었다. 1.3 독립적 학과체계 형성: 최기에는 역사학의 보조분야였던 당안학이 학문체계의 발전과 연구수준의 향상에 따라 독립적 분야가 되었다. 현재 중국의 고등교육에서 당안학과는 독립된 관리학 주제이다. 2 중국 당안학의 특징: 중국 문화와 당안관리에 뿌리를 둔 당안학은 다음과 같은 특성을 가진다: 2.1 당안실무와 밀접한 결합: 당안사업발전의 원칙 모색, 실제적 관리문제 해결, 미래예측을 목적으로 한 당안학 연구에 항상 자극을 주는 것은 끊임없이 도전적 문제와 과제를 제기하는 국가당안사업이다. 기초이론, 응용이론 및 응용기술의 비율이 균형을 이루게 되었다. 연구를 설계 조정하고 인도하는 조치들이 이루어졌다. 2.2 당안교육 및 응용기술과 함께 발전: 중국에서는 대규모 당안교육체제가 많은 성과를 거두었으며 많은 아키비스트를 양성하였다. 응용기술의 발전은 당안학의 영역을 확대시키고 당안학 이론을 진보시켰다. 2.3 국제당안연구와의 일치: 외국 및 국제기구와의 교류와 협력은 중국 아키비스트들이 상호 학습하는 효율적 방법이 되고 있다. 2.4 관련 시회과학 및 기술과의 융합: 우리의 연구는 연관된 주제, 기법 및 연구방법의 응용을 통해 진보했다. 3 현재 중국 당안학의 추세: 정보기술혁명과 국가의 개혁개방정책으로 인해 관리운영체제의 개혁, 기능적 평가 당안관의 개방 이용, 기술혁신과 신기술의 응용, 표준과 법규, 전자문건관리 등 많은 도전적이고 흥미로운 문제들이 생겨나고 있다. 미래의 진보와 발전: 보다 자유로운 연구분위기와 방법이 가치있고 효과적인 연구를 보장한다. 보다 협력적인 대형프로젝트가 양질의 연구를 보장한다. 보다 강화된 연구의 응용 전화체제가 연구의 유용성과 일반화를 보장한다.