• 설비공학논문집
• /
• 제14권6호
• /
• pp.441-449
• /
• 2002

Single-phase convection and partial nucleate boiling in free-surface and submerged jet impingements of subcooled water ejected through a 2-mm-diameter circular pipe nozzle were investigated by local measurements. Effects of jet velocity and nozzle-to-imping-ing surface distance as well as heat flux on distributions of wall temperature and heat transfer coefficients were considered. Incipience of boiling began from far downstream in contrast with the cases of the planar water jets of high Reynolds numbers. Heat flux increase and velocity decrease reduced the temperature difference between stagnation and far downstream regions with the increasing influence of boiling in partial boiling regime. The chance in nozzle-to-impinging surface distance from H/d=1 to 12 had a significant effect on heat transfer around the stagnation point of the submerged jet, but not for the free-surface jet. The submerged jet provided the lower cooling performance than the free-surface jet due to the entrainment of the pool fluid of which temperature increased.

• 설비공학논문집
• /
• 제11권6호
• /
• pp.855-860
• /
• 1999

An experimental study of jet impingement on the surface with linear temperature gradient is conducted with the presentation of the turbulent characteristics and the heat transfer rates measured when this jet impinges normally to a flat plate. The jet Reynolds number ranges from 30,000 to 90,000, the temperature gradient of the plate is 2~$4.2^{\circ}C$/cm and the dimensionless nozzle to plate distance(H/D) is from 6 to 10. The results show that the peak of heat transfer rate occurs at the stagnation point, and the heat transfer rate decreases as the radial distance from the stagnation point increases. A remarkable feature of the heat transfer rate is the existence of the second peak. This is due to the turbulent development of the wall jet. Maximum heat transfer rate occurs when the axial distance from the nozzle to nozzle diameter(H/D) is 8. The heat transfer rate can be correlated as a power function of Prandtl number, Reynolds number and the dimensionless nozzle to plate distance(H/D). It has been found that the heat transfer rate increases with increasing turbulent intensity.

• 대한기계학회논문집
• /
• 제16권8호
• /
• pp.1566-1574
• /
• 1992

본 연구에서는 원형수직 충돌분류에 의한 가열평판의 전열특성을 해석하기 위 하여 최근 표면온도 측정에 많이 사용되고 있는 liquid crystal을 이용하였다. 즉 liquid crystal의 감온특성과 영상처리 기법을 이용하여 레이놀즈수 및 노즐과 충돌판 사이의 거리(L/D) 변화에 따른 전열면의 온도장 변화를 측정하였다.

• 한국농공학회지
• /
• 제34권E호
• /
• pp.30-44
• /
• 1992

A modification of the TEACH-like computer program based on the k-$\varepsilon$ turbulence transport was applied for predicting air mixing patterns and temperature distributions in a rectangular, slot-ventilated enclosure having obstructions ; a rectangular obstacle with heat flux, solid walls separates the passage and the pig pens, and purlins beneath the ceiling. Air flow patterns were calculated for the cases with and without the purlin, extending 300mm beneath the ceiling. Comparisons of prediction data of Randall & Battams(1976) showed air flow pattern predicted well for the case without the purlin. Heat was accumulated at the corner of the left side of the solid wall and the right-upper region of the simulated pigs. However the air distribution pattern was completely different from data for the case with the purlin. The deviation from the observation may be attributed to the difference of the geometric configuation. Exploring the cause of the deviation should be conducted in a further study. Temperature stratification was also observed due to incomplete mixing. The obstruction in the route of the inlet air jet at inlet should be avoided since most of kinetic energy dissipates at the abstacle duet to impingement.

• 대한족부족관절학회지
• /
• 제8권1호
• /
• pp.46-51
• /
• 2004

Purpose: Problematic late sequelae are common following a calcaneal fracture regardless of the initial treatment. We retrospectively evaluated the painful conditions and reviewed the results of the operative treatment in patients with previously treated calcaneal fractures. Materials and Methods: Between October 1996 and September 2001, forty-three patients who underwent subsequent surgical treatment for late sequelae of calcaneal fracture were reviewed. The initial treatment consisted of only immobilization in a cast in 7 patients, closed reduction with pin fixation (Essex-Lopresti technique) in 22 and open reduction and internal fixation in 14. Painful conditions in the hind foot included subtalar arthritis in 31 patients, calcaneofibular impingement in 13, peroneal tendinitis in 6, displaced posterior bony fragment in 3, sural neuritis in 2, subtalar and midtarsal arthritis in 1 and displaced plantar bony fragment in 1. The surgical procedures for the late complications were performed at a mean of 19 months (range, 6 to 35 months) after the injury and consisted of lateral wall ostectomy and in situ subtalar fusion in 28 patients, only lateral wall ostectomy in 5 patients, lateral wall ostectomy and subtalar distraction arthrodesis in 3, removal of displaced posterior bony fragment in 3, sural nerve transposition in the peroneus brevis in 2, triple arthrodesis in 1 and removal of displaced plantar bony fragment in 1. Mean postoperative follow up period was 57 months (range, 33 to 82 months). The results of treatment were evaluated on the basis of pain, improvement in the ability to perform activities of daily living, to return to work or to a pre-injury level of activity. Results: Pain was partially relieved in 38 patients (88%), but not relieved in 5. Function improved in 34 patients (79%), and 32 (74%) returned to work or to a pre-injury level of activity. There was a trend that the longer the interval between the injury and the operation, the longer the subsequent interval until the patient returned to full activities or work. Conclusion: Meticulous physical examination and intensive prompt treatment for remaining pain after initial treatment of calcaneal fractures are recommended for patient's satisfaction and returning to work.

• 한국수자원학회논문집
• /
• 제46권9호
• /
• pp.947-956
• /
• 2013

급경사 산지하천 수충부의 호안은 대부분 콘크리트 옹벽으로 되어있다. 표면이 매끄러운 콘크리트 옹벽호안은 유속을 더 강화시키기 때문에 수충부 홍수피해의 원인이 되기도 한다. 본 연구에서는 개수로의 한 측벽에 설치한 정사각형 단면의 세로돌출줄눈이 흐름저항에 미치는 영향을 파악하기 위해 수리실험을 수행하였다. 돌출줄눈의 설치간격은 무차원 돌출줄눈 간격 ${\lambda}_{nv}$를 기준으로 조도유형 d형과 k형을 포함하도록 설계하였다. 흐름의 Froude 수는0.81~1.12의 범위였다. 흐름저항은 돌출줄눈의 설치간격과 유량에 좌우되었다. ${\lambda}_{nv}$가 9일 때 흐름저항이 가장 큰 것으로 나타났다. 세로돌출줄눈은 유량이 증가하면 d형 조도에서는 흐름저항을 감소시켰으나 k형 조도에서는 흐름저항을 증가시켰다. 흐름저항의 증가폭은 ${\lambda}_{nv}$이 9~12의 범위에서 상대적으로 더 크게 나타났다. 세로돌출줄눈에 의한 흐름저항은 대부분 형상저항에 의한 것이며 그 등가조도높이는 수심규모로 발생할 수 있고 흐름저항에 미치는 영향이 매우 크다. 측벽의 세로돌출줄눈은 흐름저항을 증가시키고 최대유속의 발생위치를 수로의 횡단면 중앙방향으로 이동시키는 수단으로 사용될 수 있을 것이다.

• 대한물리의학회지
• /
• 제8권3호
• /
• pp.369-378
• /
• 2013

PURPOSE: The purpose of present study was to ascertain how the activity of the serratus anterior muscle, the upper trapezius muscle and the pectoral major muscle was affected while the upper arm was being flexed at 70, 90 and 110 degrees respectively in a closed kinetic chain exercise (wall push up plus) and an open kinetic chain exercise (static hug). METHODS: Sixteen healthy young men subjects participated in the study. Surface electromyography (EMG) data were collected from the dominant-side muscles during a closed kinetic chain exercise and an open kinetic chain exercise. The activity of each muscle was measured quantitatively, and by the use of the two-way repeated ANOVA, the data were compared with each other according to exercises and shoulder flexion angles. RESULTS: Results indicated that the closed kinetic chain exercise did not interact with the open kinetic chain exercise (p>.05). In both the closed kinetic chain exercise and the open kinetic chain exercise, the activity of the serratus anterior muscle became different significantly according to angles (p<.05). Its activity increased in order of 70, 90 and 110 degrees (p<.05). In both exercises and all angles, muscle activity was significantly higher in the serratus anterior muscle than in the upper trapezius muscle and the pectoral major muscle (p<.05). CONCLUSION: The above results show that there is a need to selectively control the exercise stress of the serratus anterior muscle in the case of the patients with the shoulder impingement syndrome characterized by the winged scapula, insufficient scapular protraction and upward rotation.

• 대한기계학회논문집B
• /
• 제21권9호
• /
• pp.1115-1125
• /
• 1997

Experiments have been conducted to obtain local and average heat transfer coefficients associated with impingement of a row of circular, free surface-water jets on a constant heat flux surface. Nozzle arrays are a row of 3 jets (nozzle dia.=4.6 mm) and a row of 5 jets (nozzle dia.=3.6 mm), and the nozzle configuration is Reverse cone type revealed good performance in heat transfer. Nozzle-to-plate spacings ranging from 16 mm to 80 mm were investigated for two jet center to center spacings 25 mm and 37.5 mm in the jet velocity of 3 m/s (R $e_{D}$=27000) to 8 m/s (R $e_{D}$=70000). For a row of 3 jets and a row of 5 jets, the stagnation heat transfer of the central jet is lower than that of adjacent jets. In the wall jet region between jets, for small nozzle-to-plate spacing and large jet velocity, the local maximum in the Nusselt number was observed, however, for small jet velocity or large nozzle-to-plate spacing, the local maximum was not observed. Except for the condition of $V_{O}$=8 m/s and H/D=10, the average Nusselt number reveals the following ranking: a row of 5 jets, a row of 3 jets, single jet. For a row of 3 jet, the maximum average Nusselt number occurs at H/D=8 ~ 10, and for a row of 5 jets, it occurs at H/D=2 ~ 4. Compared with the single jet, enhancement of average heat transfer for a row of 3 jets is approximately 1.52 ~ 2.28 times, and 1.69 ~ 3.75 times for a row of 5 jets.ets.s.

• The Journal of Korean Physical Therapy
• /
• 제36권2호
• /
• pp.71-77
• /
• 2024

Purpose: The prolonged use of digital devices has led to the widespread adoption of poor postures, particularly rounded shoulder posture (RSP), associated with shoulder impingement and pain. This study investigates the effects of neuromuscular electrical stimulation (NMES) on RSP in healthy adults. Methods: Thirty adults with RSP were randomly assigned to NMES only, exercise only, or NMES with exercise groups. NMES was applied to the lower trapezius, which was the target muscle in this study, for a total of 2 weeks, 5 times per week, 20 minutes per session. The exercise program included pectoralis minor stretching, wall-slide exercise, dynamic hug exercise with band, and Brugger stretching for upper body with band, which were performed for a total of 2 weeks, 5 times per week, 20 minutes per session. Outcome measures, including the Supine Method (SM) for posture and surface electromyography (EMG) of the lower trapezius for muscle activity, were assessed before the intervention, after 5 sessions, and after 10 sessions. Results: All the groups showed significant changes in the SM and % maximal voluntary isometric contraction (%MVIC) over time (p<0.05). The NMES group had significantly reduced SM at 1 week, while the exercise and combined groups had reduced SM at 2 weeks (p<0.017). All the groups had increased %MVIC at 2 weeks (p<0.017), with no significant differences observed between groups. Conclusion: NMES alone can be as effective as exercise in improving RSP. NMES combined with exercise also showed positive outcomes, thus offering diverse treatment options for this condition.

• Hip & pelvis
• /
• 제36권1호
• /
• pp.26-36
• /
• 2024

Total hip arthroplasty (THA) is a frequently performed procedure; the objective is restoration of native hip biomechanics and achieving functional range of motion (ROM) through precise positioning of the prosthetic components. Advanced three-dimensional (3D) imaging and computed tomography (CT)-based navigation are valuable tools in both the preoperative planning and intraoperative execution. The aim of this study is to provide a thorough overview on the applications of CT scans in both the preoperative and intraoperative settings of primary THA. Preoperative planning using CT-based 3D imaging enables greater accuracy in prediction of implant sizes, leading to enhancement of surgical workflow with optimization of implant inventory. Surgeons can perform a more thorough assessment of posterior and anterior acetabular wall coverage, acetabular osteophytes, anatomical landmarks, and thus achieve more functional implant positioning. Intraoperative CT-based navigation can facilitate precise execution of the preoperative plan, to attain optimal positioning of the prosthetic components to avoid impingement. Medial reaming can be minimized preserving native bone stock, which can enable restoration of femoral, acetabular, and combined offsets. In addition, it is associated with greater accuracy in leg length adjustment, a critical factor in patients' postoperative satisfaction. Despite the higher costs and radiation exposure, which currently limits its widespread adoption, it offers many benefits, and the increasing interest in robotic surgery has facilitated its integration into routine practice. Conducting additional research on ultra-low-dose CT scans and examining the potential for translation of 3D imaging into improved clinical outcomes will be necessary to warrant its expanded application.