• Journal of Biosystems Engineering
• /
• v.37 no.2
• /
• pp.75-81
• /
• 2012

Oyster mushroom farm which could not meet optimum temperature range yields non-uniform sized, low quality products. Thus, this study, utilizing STAR CCM+, one of the computational fluid dynamics (CFD) programs, analyzed the impact of air circulation and temperature distribution. Methods: After we visited numerous mushroom farms, we measured the temperature at the discharge ports of heaters, fan capacity, and the locations of the air circulators in the farms. According to the data, most mushroom growers installed the heaters near the entrance and discharge ports of the heaters at the third growing bed on the same height as the heaters in the entrance. The temperature at the discharge port of heater was $1,26^{\circ}C$, and the fan capacity was 4,500 $m^3$/hr. The air circulator was placed in the center of the mushroom farm 50cm above the ground, and its capacity of inlet port was 1,100 $m^3$/hr and discharge port 1,600 $m^3$/hr. The mushroom farm was insulated. Results: According to the analysis of the temperature distribution in the vertical plane of the entrance side, no air circulation causes the high temperature zone of 296~299K at the discharge port of the heater to take up 34% of area while the operation of air circulators causes it to occupy only 9%. This means that not using air circulators leads to a concentration of high temperature at the discharge port near the entrance. In addition, with the results of the analysis of the temperature distribution in the vertical planes of the center, no air circulation causes the temperature zone of 295~298K at the discharge port of the heater to take up 48% of area while the operation of air circulators causes it to occupy 80%. This shows that the high outlet port temperature disseminated to the center. Conclusions: After ninety minute operation of both heater and air circulator, the interior temperature became stabilized in the mushroom farm. Air circulation made the high temperature at the discharge port disseminate to the center and exit in the farm and equalize the temperature distribution.

• Journal of Radiation Protection and Research
• /
• v.42 no.2
• /
• pp.114-129
• /
• 2017

Background: The purpose of this paper is to confirm the event timings and the magnitude of fission product aerosol release from the Fukushima accident. Over a few hundreds of technical papers have been published on the environmental impact of Fukushima Daiichi accident since the accident occurred on March 11, 2011. However, most of the research used reverse or inverse method based on the monitoring of activities in the remote places and only few papers attempted to estimate the release of fission products from individual reactor core or from individual spent fuel pool. Severe accident analysis code can be used to estimate the radioactive release from which reactor core and from which radionuclide the peaks in monitoring points can be generated. Materials and Methods: The basic material used for this study are the initial core inventory obtained from the report JAEA-Data/Code 2012-018 and the given accident scenarios provided by Japanese Government or Tokyo Electric Power Company (TEPCO) in official reports. In this research a forward method using severe accident progression code is used as it might be useful for justifying the results of reverse or inverse method or vice versa. Results and Discussion: The release timing and amounts to the environment are estimated for volatile radioactive fission products such as noble gases, cesium, iodine, and tellurium up to 184 hours (about 7.7 days) after earthquake occurs. The in-plant fission product behaviors and release characteristics to environment are estimated using the severe accident progression analysis code, MELCOR, for Fukushima Daiichi accident. These results are compared with other research results which are summarized in UNSCEAR 2013 Report and other technical papers. Also it may provide the physically based arguments for justifying or suspecting the rationale for the scenarios provided in open literature. Conclusion: The estimated results by MELCOR code simulation of this study indicate that the release amount of volatile fission products to environment from Units 1, 2, and 3 cores is well within the range estimated by the reverse or inverse method, which are summarized in UNSCEAR 2013 report. But this does not necessarily mean that these two approaches are consistent.

• The Korean Journal of Food And Nutrition
• /
• v.17 no.1
• /
• pp.41-46
• /
• 2004

This study was designed to investigate the effective ratio of healthy bread with jasmin tea powder. The weight, volume, and color difference of bread with various jasmin tea powder was measured and the picture of bread was taken and the panel test was taken. The weight of bread was increased and the volume was decreased significantly according to increase of jasmin tea powder. To avoid the decrease of volume, the active gluten was added, but there was not shown the increse of bread volume by active gluten. In the result of panel test and volume measurement, addition of 3% jasmin tea powder was appropriate. Therefore, using the jasmin tea powder, the diversity of bread by functionality, nutritional composition, taste, color, flavor of jasmin tea powder can be developed. This result will support the background the development of jasmin tea bread of good quality.

• KIISE Transactions on Computing Practices
• /
• v.21 no.1
• /
• pp.13-18
• /
• 2015

Computational science simulations have been used to enable discovery in a broad spectrum of application areas, these simulations show irregular demanding characteristics of computing resources from time to time. The adoption of virtualized high performance cloud, rather than CPU-centric computing platform (such as supercomputers), is gaining interest of interests mainly due to its ease-of-use, multi-tenancy and flexibility. Basically, provisioning a virtual cluster, which consists of a lot of virtual machines, in a real-time has a critical impact on the successful deployment of the virtualized HPC clouds for computational science simulations. However, the cost of concurrently creating many virtual machines in constructing a virtual cluster can be as much as two orders of magnitude worse than expected. One of the main factors in this bottleneck is the time spent to create the virtual images for the virtual machines. In this paper, we propose a novel technique to minimize the creation time of virtual machine images and improve I/O performance of the provisioned virtual clusters. We also confirm that our proposed technique outperforms the conventional ones using various sets of experiments.

• Journal of Korea Water Resources Association
• /
• v.48 no.10
• /
• pp.857-868
• /
• 2015

Hydraulic and water quality models with high reliability are necessary for the efficient management of water quality in the reservoir. The model capacity can be demonstrated by the application for the various hydrological conditions. CE-QUAL-W2 model is laterally averaged two-dimensional hydraulic and water quality model. The W2 model, which is suitable for the narrow reservoir like the Jinyang reservoir as compared with the depth and length of waterbody, has been frequently used by many researchers. Namgang watershed is expected to increase the water demand. In this study, the W2 model is validated under two different hydrological conditions; wet year (2011) and normal year (2009). Using hydrological and water quality condition for calibration, 2011, the effect of water intake increase was simulated. The simulation results showed that the increase of water intake led to increase the concentrations in total nitrogen, total phosphorus and Chlorophyll-${\alpha}$ concentration. Especially the concentration increase was appeared during the dry season in each of up to 62.53% (Total nitrogen), 39.07% (Total phosphorus) and 232.19% (Chlorophyll-${\alpha}$). The changes of chlorophyll-${\alpha}$ is similar to those of total phosphorus concentration.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.3
• /
• pp.64-69
• /
• 2007

Motion control of the system is a position control of motor. Motion control of an uncertain robot system is considered as one of the most important and fundamental research directions in the robotics. Some distinguished works using linear control, adaptive control, robust control strategies based on computed torque methodology have been reported. However, it is generally recognized within the control community that these strategies suffer from the following problems : the exact robot dynamics are needed and hard to implement, the adaptive control cannot guarantee the performance during the transient period for adaptation under the variation, the robust control algorithms such as the sliding mode control need information on the bounds of the possible uncertainty and disturbance. And it produces a large control input as well. In this dissertation, a motion control for the unmanned intelligent robot system using disturbance observer is studied. This system is affected with an impact vibration disturbance. This paper describes a stable motion control of the system with the consideration of external disturbance. To obtain the stable motion independently against the external disturbance, the disturbance rejection is strongly required. To address the above issue, this paper presents a Disturbance OBserver(DOB) control algorithm. The validity of the suggested DOB robust control scheme is confirmed by several computer simulation results. And the experiments with a motor system is performed to give the validity of applicability in the industrial field. This results make the easier implementation of the controller possible in the field.

• Journal of the Korea Concrete Institute
• /
• v.28 no.6
• /
• pp.673-683
• /
• 2016

In recent years, frequent terror or military attack by explosion, impact, fire accidents have occurred. Particularly, World Trade Center collapse and US Department of Defense Pentagon attack on Sept. 11 of 2001. Also, nuclear power plant incident on Mar. 11 of 2011. These attacks and incidents were raised public concerns and anxiety of potential terrorist attacks on major infrastructures and structures. Therefore, the extreme loading researches were performed of prestressed concrete (PSC) member, which widely used for nuclear containment vessel and gas tank. In this paper, to evaluate the blast resistance capacity and its protective performance of bi-directional unbonded prestressed concrete member, blast tests were carried out on $1,400{\times}1,000{\times}300mm$ for reinforced concrete (RC), prestressed concrete without rebar (PSC), prestressed concrete with rebar (PSRC) specimens. The applied blast load was generated by the detonation of 55 lbs ANFO explosive charge at 1.0 m standoff distance. The data acquisitions not only included blast waves of incident pressure, reflected pressure, and impulse, but also included displacement, acceleration, and strains at steel, concrete, PS tendon. The results can be used as basic research references for related research areas, which include protective design and blast simulation under blast loading.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.38 no.3
• /
• pp.64-77
• /
• 2015

An effective method for produce munitions effectiveness data is to calculate weapon effectiveness indices in the US military's Joint Munitions Effectiveness Manuals (JMEM) and take advantage of the damage evaluation model (GFSM) and weapon Effectiveness Evaluation Model (Matrix Evaluator). However, a study about the Range Safety that can be applied in the live firing exercises is very insufficient in the case of ROK military. The Range Safety program is an element of the US Army Safety Program, and is the program responsible for developing policies and guidance to ensure the safe operation of live-fire ranges. The methodology of Weapon Danger Zone (WDZ) program is based on a combination of weapon modeling/simulation data and actual impact data. Also, each WDZ incorporates a probability distribution function which provides the information necessary to perform a quantitative risk assessment to evaluate the relative risk of an identified profile. A study of method to establish for K-Range Safety data is to develop manuals (pamphlet) will be a standard to ensure the effective and safe fire training at the ROK military education and training and environmental conditions. For example, WDZs are generated with the WDZ tool as part of the RMTK (Range Managers Tool Kit) package. The WDZ tool is a Geographic Information System-based application that is available to operational planners and range safety manager of Army and Marine Corps in both desktop and web-based versions. K-Range Safety Program based on US data is reflected in the Korean terrain by operating environments and training doctrine etc, and the range safety data are made. Thus, verification process on modified variables data is required. K-Range Safety rather than being produced by a single program, is an package safety activities and measures through weapon danger zone tool, SRP (The Sustainable Range Program), manuals, doctrine, terrain, climate, military defence M&S, weapon system development/operational test evaluation and analysis to continuously improving range safety zone. Distribution of this K-range safety pamphlet is available to Army users in electronic media only and is intended for the standing army and army reserve. Also publication and distribution to authorized users for marine corps commands are indicated in the table of allowances for publications. Therefore, this study proposes an efficient K-Range Safety Manual producing to calculate the danger zones that can be applied to the ROK military's live fire training by introducing of US Army weapons danger zone program and Range Safety Manual

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.5
• /
• pp.16-24
• /
• 2011

The IEEE 802.11 wireless LAN (Local Area Network) is widely used for wireless access due to its easy deployment and low cost. Multicast in wireless LANs is very useful for transmitting data to multiple receivers compared to unicast to each receiver. In the IEEE 802.11 wireless LAN, multicast transmissions are unreliable since multicast data packets are transmitted without any feedback from receivers. Recently, various protocols have been proposed to enhance the reliability of multicast transmissions. They still have serious problems in reliability and efficiency due to the excessive control overhead by the use of a large number of control packets in the error recovery process, and due to a large number of retransmissions to satisfy all receivers. In this paper, we propose an effective scheme called PTRM(Proactive Transmission based Reliable Multicast). The proposed scheme uses a block erasure code to generate parity packets and to reduce the impact of independent packet error among receivers. After generating parity packets, the PTRM transmits data packets as many as receivers need to recover error, and then requests feedback from them. The simulation results show that the proposed scheme provides reliable multicast while minimizing the feedback overhead.

• Journal of Korea Water Resources Association
• /
• v.43 no.3
• /
• pp.295-308
• /
• 2010

As an attempt to explore the impact of droughts which may be worse by the climate change, the change in the water balance of the Han-river basin is analyzed. To accomplish it, we suggest a procedure consisting of three successive sub-procedures: daily rainfall generation for 70 years by the RegCM3 RCM ($27{\times}27\;km$) with the A2 scenario, daily discharge simulations by SLURP using the generated daily rainfall data, and monthly water balance analysis by K-WEAP (Korean Water Evaluation and Planning System) based on the SLURP simulation. Since significant uncertainty is involved in forecasting the future water consumption and water yields, we assumed three water consumption scenarios and fifty water yields scenarios. Three water consumption scenarios are, namely, "LOW", "MEDIUM", and "HIGH" according to the expected amount of water consumption. The fifty daily discharges are obtained from the SLURP simulations during the drought period. Finally, water balance analysis is performed by K-WEAP based on 150 combinations from three water consumption scenarios and the fifty daily discharges. Analysis of water scarcity in small basins of the Han River basin showed concentration of water scarcity in some small basins. It was also found that water scarcity would increase in all small basins of the Han River basin.