• Journal of Ocean Engineering and Technology
• /
• v.21 no.3 s.76
• /
• pp.71-76
• /
• 2007

Recently, many industries have been employing the application of laser beam welding, due to the resulting high welding quality, such as smaller width of melting and heat affective zone, smaller welding deformation, and fine grains of weldment, compared to arc welding. However, in order to appropriately utilize this welding process with steel structure, the characteristics of welding residual stresses and fracture toughness in welded joints are to be investigated for reliability. Therefore, in this study, the mechanical properties of weldments by arc and laser welding are investigated using FEM to confirm the weldability of laser welding to the general structural steel (HT50). The Charpy impact test and 3-points bending CTOD test are carried out in the range of temperatures between $-60^{\circ}C\;and\;20^{\circ}C$, in order to understand the effect on the fracture toughness of weldments. From the research results, it has been found that the maximum residual stress appears at the center of plate thickness, and that the fracture toughness is influenced by strength mis-match.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.4
• /
• pp.519-526
• /
• 2002

In this paper, a microstrip patch array antenna for a Doppler radar at 10.525GHz is desinged and fabricated. To be used for mobile radar system, the antenna is fabricated on a single layer laminate to resist a fire impact and is covered with the Teflon foam. To obtain the desired characteristics, the array antenna is designed 4$\times$8 array using a corporate 3-dB amplitude taper. Also, using square patch elements, the antenna can be converted to a circular polarized antenna later. The designed and fabricated array antenna has the reflection coefficient$({S_11})$ -53.498dB, the horizontal beam width of $10^{\circ}$, the vertical beam width of $18.8^{\circ}$, the gain of 21dBi, the bandwidth of 220MHz for VSWR<1.5 and a side lobe level of less than -17.5dB.

• Current Optics and Photonics
• /
• v.4 no.1
• /
• pp.9-15
• /
• 2020

Fresnel zone plates have been widely used in many applications, such as x-ray telescopes, microfluorescence, and microimaging. To obtain an x-ray Fresnel zone plate, many fabrication methods, such as electron-beam etching, ion-beam etching and chemical etching, have been developed. Fresnel zone plates fabricated by these methods will inevitably lead to some nonideal factors, which have an impact on the focusing characteristics of the zone plate. In this paper, the influences of these nonideal factors on the focusing characteristics of the zone plate are studied systematically, by numerical simulations based on scalar diffraction theory. The influence of the thickness of a Fresnel zone plate on the absolute focusing efficiency is calculated for a given incident x-ray's wavelength. The diffraction efficiency and size of the focal spot are calculated for different incline angles of the groove. The simulations of zone plates without struts, with regular struts, and with random struts are carried out, to study the effects of struts on the focusing characteristics of a zone plate. When a Fresnel zone plate is used to focus an ultrashort x-ray pulse, the effect of zone-plate structure on the final pulse duration is also discussed.

• Composites Research
• /
• v.29 no.5
• /
• pp.249-255
• /
• 2016

The fiber metal laminates have been widely used at aerospace industry due to outstanding fatigue characteristic, corrosion resistance and impact resistance and so forth. The objective of this research is to establish the proper manufacturing variables for enhancing the interfacial energy release rate of fiber metal laminates using Taguchi method. The major variables of the manufacturing process are surface treatment, pre-specified temperature holding time and additional pressure. In order to determine the interfacial adhesive strength, the double cantilever beam and end-notched flexure tests were conducted. Afterward, Mode I and II energy release rates at various conditions were introduced signal-to-noise ratio with respect to each condition. Finally, the most efficient manufacturing variables are recognized using larger-the-better characteristic.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.274-274
• /
• 2012

In-depth analysis by secondary ion mass spectrometry (SIMS) is very important for the development of electronic devices using multilayered structures, because the quantity and depth distribution of some elements are critical for the electronic properties. Correct determination of the interface locations is critical for the calibration of the depth scale in SIMS depth profiling analysis of multilayer films. However, the interface locations are distorted from real ones by the several effects due to sputtering with energetic ions. In this study, the determination of interface locations in SIMS depth profiling of multilayer films was investigated by Si/Ge and Ti/Si multilayer systems. The original SIMS depth profiles were converted into compositional depth profiles by the relative sensitivity factors (RSF) derived from the atomic compositions of Si-Ge and Si-Ti alloy reference films determined by Rutherford backscattering spectroscopy. The thicknesses of the Si/Ge and Ti/Si multilayer films measured by SIMS depth profiling with various impact energy ion beam were compared with those measured by TEM. There are two methods to determine the interface locations. The one is the feasibility of 50 atomic % definition in SIMS composition depth profiling. And another one is using a distribution of SiGe and SiTi dimer ions. This study showed that the layer thicknesses measured with low energy oxygen and Cs ion beam and, by extension, with method of 50 atomic % definition were well correlated with the real thicknesses determined by TEM.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.1
• /
• pp.48-55
• /
• 2018

The purpose of the present study is to compare the reduction rate of natural frequency and the increase rate of damping parameter with structural damage in system. For this purpose, experiment and numerical simulation analysis are performed for the 2-span H-Beam with lower natural frequency and higher damping parameter from free vibration in structure. The response signal by impact load before and after damage is analyzed at 14 locations. The response signals for all locations are performed fast fourier transform to estimate the natural frequency reduction rate and wavelet transform to estimate the damping parameter increase rate. The time domain function corresponding to each scale(frequency) is separated from the response signal by wavelet parameter. The estimation of damping parameter increase rate using wavelet transform is more sensitive than the estimation of natural frequency reduction rate in structure.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.7
• /
• pp.43-50
• /
• 2004

For the simultaneous measurement of strain and damage signal a fiber Bragg grating sensor system with a dual demodulator was proposed. The dual demodulator is composed of a demodulator using a tunable Fabry-Perot filter measuring the low-frequency signal with large magnitude such as strain and the other using a passive Mach-Zehnder interferometer detecting the high-frequency signal with small amplitude such as impact or damage signal. Using the proposed fiber Bragg grating sensor system, both the strain and damage signals of a cross-ply laminated composite beam under tensile loading were simultaneously measured. The strain and damage signals detected by single fiber Bragg grating sensor showed that sudden strain shifts were accompanied with vibration at a maximum frequency of several hundreds of kilohertz at the instant of matrix crack propagation in the 90 degree layer in composite beam.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.12A
• /
• pp.1276-1285
• /
• 2007

Since the TD-SCDMA (Time Division-Synchronous Code Division Multiple Access) system is based on TDD (Time Division Duplexing), the uplink and downlink can be allocated asymmetrically according to the traffic e.g. Web browsing. Although this asymmetric allocation can increase the frequency utilization, it may cause time slot opposing, which implies the time slot is assigned in opposing direction between cells. The time slot opposing can generate significant interference between cells, which results in severe performance degradation. In the paper, a novel dynamic channel allocation (DCA) is proposed in the TD-SCDMA system, to mitigate the impact of time slot opposing considering smart antenna. When the smart antenna is applied in the system, the inter-cell interference is largely affected by beam pattern and beam direction between neighboring cells. Therefore, the time slot opposing and smart antenna should be considered together in the DCA. The intensive simulations show that the proposed scheme can improve the system capacity compared to the conventional DCA schemes.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.449-449
• /
• 2011

We reported the direct effect of intrinsic surface energy of dry adhesive material to the Van der Waals and capillary forces contributions of the total adhesion force in an artificial gecko-inspired adhesion system. To mimic the gecko foot we fabricated tilted nanohairy structures using both lithography and ion beam treatment. The nanohairy structures were replicated from Si wafer mold using UV curable polymeric materials. The control of nanohairs slanting angles was based on the uniform linear argon ion irradiation to the nanohairy polymeric surface. The surface energy was studied utilizing subsequent conventional oxygen ion treatment on the nanohairy structures which resulted in gradient surface energy. Our shear adhesion test results were found in good agreement with the accepted Van der Waals and capillary forces theory in the gecko adhesion system. Surface energy would give a direct impact to the effective Hamaker constant in Van der Waals force and the filling angle (${\varphi}$) of water meniscus in capillary force contributions of gecko inspired adhesion system. With the increasing surface energy, the effective Hamaker constant also increased but the filling angle decreased, resulting in a competition between the two forces. Using a simple mathematical model, we compared our experimental results to show the quantitative contributions of Van der Waals and capillary forces in a single adhesion system on both hydrophobic and hydrophilic surfaces. We found that the Van der Waals force contributes about 82.75% and 89.97% to the total adhesion force on hydrophilic and hydrophobic test surfaces, respectively, while the remaining contribution was occupied by capillary force. We also showed that it is possible to design ultrahigh dry adhesive with adhesion strength of more than 10 times higher than apparent gecko adhesion force by controlling the surface energy and the slanting angle induced-contact line of dry adhesive the materials.

• Imaging Science in Dentistry
• /
• v.43 no.1
• /
• pp.25-30
• /
• 2013

Purpose: This study was performed to determine the prevalence of bifid mandibular condyles (BMCs) in asymptomatic and symptomatic temporomandibular joint (TMJ) subjects with no traumatic history, and to assess their impact on clinical and radiographic manifestations of TMJ. Materials and Methods: A total of 3,046 asymptomatic and 4,378 symptomatic patients were included in the study. Cone-beam computed tomography (CBCT) images were reviewed for bifid condyles. T-tests were used to compare the frequency of BMCs when stratified by symptom, gender, and side. In BMC patients, the clinical features of pain and noise, osseous changes, and parasagittal positioning of the condyles were compared between the normally shaped condyle side and the BMC side using chi-squared tests. Results: Fifteen (0.49%) asymptomatic and 22 (0.50%) symptomatic patients were found to have BMCs. Among the bilateral cases, the number of condyles were 19 (0.31%) and 25 (0.29%), respectively. No statistically significant differences were found between asymptomatic and symptomatic patients, between female and male patients, or between the right and left sides (p>0.05). Compared with the normally shaped condyle side, the BMC side showed no statistically significant differences in the distribution of pain and noise, parasagittal condylar position, or condylar osseous changes, with the exception of osteophytes. In the symptomatic group, osteophytes were found more frequently on the normally shaped condyle side than the BMC side (p<0.05). Conclusion: BMCs tended to be identified as an incidental finding. The presence of BMC would not lead to any TMJ symptoms or cause osseous changes.