• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.5
• /
• pp.35-44
• /
• 2011

In a spark ignition engine, a variable valve lift (VVL) system has been developed for high fuel efficiency and low power loss. However, changes in valve lift cause deviations of cylinder air charge which lead to individual cylinder equivalence ratio maldistribution. In this study, in order to reduce the maldistribution, we propose individual cylinder equivalence ratio estimation and control algorithms. The estimation algorithm calculates the equivalence ratio of each cylinder by using a mathematical engine model which includes air charging, fuel film, exhaust gas, and universal exhaust gas oxygen sensor (UEGO) dynamics at various valve lifts. Based on the results of estimated equivalence ratio, the injection quantity of each cylinder is adjusted to control the individual cylinder equivalence ratio. Estimation and control performance are validated by engine experiments. Experimental results represented that the equivalence ratio maldistribution and variation are decreased by the proposed algorithms.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.5
• /
• pp.151-156
• /
• 2013

The experiment was done on cars travelling at the speeds of 20km/h, 60km/h and 100km/h using the performance testing mode for chassis dynamometer. In this experiment, the relativity between the secondary waveform coming from ignition coil and exhaust emissions were measured in case of cars with failures, in oxygen sensor, spark plugs. The following results obtained by analysis of the relativity between the secondary waveform and exhaust emissions. 1) When the oxygen sensor is failure, the average value of CO emission measured was 6.8 times higher than the standard CO emission value and the average value of HC emission measured was 2.3 times higher than the standard emission level. 2) When engine parts are in failure, more fuel enters the cylinder due to longer opening duration of injector, and it tended to make CO and HC emission values increase. 3) Combustion duration, the shape of flame propagation during spark line, and the size of the discharge-induced energy were the three main elements that directly cause variations in CO and HC emission values.

• Journal of ILASS-Korea
• /
• v.18 no.1
• /
• pp.21-26
• /
• 2013

Diesel low temperature combustion (LTC) is the concept where fuel is burned at a low temperature oxidation regime so that $NO_x$ and particulate matters (PM) can simultaneously be reduced. There are two ways to realize low temperature combustion in compression ignition engines. One is to supply a large amount of EGR gas combined with advanced fuel injection timing. The other is to use a moderate level of EGR with fuel injection at near TDC which is generally called Modulated kinetics (MK) method. In this study, the effects of fuel injection pressure on performance and emissions of a single cylinder engine were evaluated using the latter approach. The engine test results show that MK operations were successfully achieved over a range of with 950 to 1050 bar in injection pressure with 16% $O_2$ concentration, and $NO_x$ and PM were significantly suppressed at the same time. In addition, with an increase in fuel injection pressure, the levels of smoke, THC and CO were decreased while $NO_x$ emissions were increased. Moreover, as fuel injection timing retarded to TDC, more THC and CO emissions were generated, but smoke and $NO_x$ were decreased.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.3
• /
• pp.8-13
• /
• 2018

Zirconium potassium perchlorate(ZPP) is an igniter composed of potassium perchlorate as an oxidizing agent and zirconium as a fuel with a Viton binder. ZPP has been used to provide an ignition source in the aerospace, propulsion, and automotive industries. This study investigates the manufacturing process and characteristics of ZPP, such performance and shape/calorimetry/pressure characteristics with respect to pyrotechnic mechanical device(PMD). During the production of ZPP, the mixing process was designed to produce uniform particle size and shape by mixing the raw materials at high speed.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.10
• /
• pp.587-594
• /
• 2002

A low frequency square wave electronic ballast for the high intensity discharge(HID) lamps using fuzzy logic controller is developed. This electronic ballast consists a buck converter, a low frequency square wave full bridge inverter, a high voltage pulse generator for the HID lamp ignition, an over current protection circuit and an 8-bit microcontroller. The ballast system is operated on the constant current mode during the HID lamp start-up process and the system is operated on the constant power mode during steady state. Experimental results show that the fuzzy logic control operation is carried out successfully by the 8-bit microcontroller PIC16F877 In this electronic ballast system, in spite of the limited control bandwidth caused by low operating speed of the microcontroller, the good performance in the constant lamp current characteristic is obtained. Acoustic resonance of the HID lamps can be effectively avoided because the instantaneous In lamp power is fully constant due to the low frequency square wave drive.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.2
• /
• pp.184-191
• /
• 1999

Th effects of exhaust gas recirculation(EGR) on the characteristics of combustion exhaust emissions and specific fuel consumption(SFC) are experimentally investigated by four-cylin-der four-cycle and direct injection marine diesel engine. In order to reduce soot contents in the recirculated exhaust gas to intake system of the engines a novel diesel soot removal system with a cylinder-type scrubber which has water injector(4 nozzles in 1.0mm diameter)is specially designed and manufactured for the experi-mental system. The obtained results are as follows; The combustion pressure in cylinder is decreased and ignition is delayed with increasing EGR rate. The accumulated quantity of heat release is slightly decreased and the tendency of heat release rate is not constant. NOx and Soot emissions are decreased by maximum 7% and 540% with scrubber tan without scrubber in the range of experimental conditions. Those are increased at the lean burn area with increasing equivalence ration in the constant value of engine speed and EGR rate. Also those are decreased with increasing EGR rate in the constant value of engine speed and equivalence ratio.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2928-2933
• /
• 2008

Trends of the automotive market require the application of new engine technologies, which allows for the use of different types of fuel. Since ethanol is a renewable source of energy and it contributes to lower $CO_2$ emissions, ethanol produced from biomass is expected to increase in use as an alternative fuel. It is recognized that for spark ignition (SI) engines ethanol has advantages of high octane number and high combustion speed. In spite of the advantages of ethanol, fuel supply system might be affected by fuel blends with ethanol like a wear and corrosion of electric fuel pumps. So the on-board hydrogen production out of ethanol reforming can be considered as an alternative plan. This paper investigates the influence of ethanol fuel on SI engine performance, thermal efficiency and emissions. The combustion characteristics with hydrogen-enriched gaseous fuel from ethanol reforming are also examined.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.7 no.2
• /
• pp.44-53
• /
• 2003

A vertical hot-firing test facility was established to carry out the IPPT(Integrated Propulsion Performance Test) and SQT(Stage Qualification Test) of KSR-III(Korea Sounding Rocket-III). The components for actual launcher were mostly used, hence these tests were carried out under the condition of relatively lower safety margin. To perform hot-firing tests with the maximum safety, an engine emergency blockage system was investigated and applied. An emergency blockage system using combustion chamber pressures and acceleration signals was set up to monitor ignition delay and fail, flame out, propellant feeding status, unstable combustion and excessive structural vibration. With such a system, the test safety could be secured by rapid judgement and follow-up measures, which made IPPT and SQT be safely completed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.71-74
• /
• 2010

Using the technology demonstration model of 75-tonf-class combustor which is expected to be used to the rocket engine of a korean space launch vehicle, 2 times of firing tests were carried out. Firing tests were done at 50% of the nominal flow rate because of incapability of the test facility and limit of the test bed strength. Through the low pressure firing tests of 75-tonf-class channel cooling thrust chamber, reliability and stability at the ignition and combustion phases were confirmed. Additionally it was foreseen that the 75-tonf-class thrust chamber would satisfy the performance requirements.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.445-450
• /
• 2017

ZPP(Zirconium Potassium Perchlorate) is an igniter composed of potassium perchlorate as oxidizing agent and zirconium as fuel with a Viton binder. ZPP is used to provide ignition in the aerospace, propulsion, automotive industries. This research is investigated for the manufacturing process and characteristics analysis of the ZPP such as the performance and shape/calorimetry/pressure characteristics of the ZPP on PMD(Pyrotechnic Mechanical Device). During the production of ZPP, the mixing process was designed so that the ZPP could be produced in uniform particle size and shape by mixing the raw materials at high speed.