• 대한조선학회논문집
• /
• 제49권6호
• /
• pp.478-483
• /
• 2012

The speed performances of ice sea trial on the Arctic(2010 & 2011) area were shown different results depend on the ice floe size. Penetration phenomena of level ice was not happened on medium ice floe and tore up by the impact force because the mass of medium ice floe is similar to the mass of Araon which is Korean ice breaking research vessel and did not shut up by the ice ridge or iceberg. The sea trial on the Amundsen sea was performed at the big floe which is classified by WMO(World Meteorological Organization). Three measurements of ice properties and five results of speed trial were obtained with different ice thicknesses and engine powers. To evaluate speed of level ice trial and model test results at the same ice thickness and engine power, the correction method of HSVA(Hamburg Ship Model Basin) was used. The thickness, snow effect, flexural strength and friction coefficient were corrected to compare the speed of sea trial. The analyzed speed at 1.03m thickness of big floe was 5.85 knots at 10MW power and it's 6.10 knots at 1.0m ice thickness and the same power. It's bigger than the results of level ice because big floe was also slightly tore up by the impact force of vessel based on the observation of recorded video.

• 한국지반공학회논문집
• /
• 제32권12호
• /
• pp.33-43
• /
• 2016

노후관로로 인한 지반내 공동형성과 지반이완 메카니즘을 분석하기 위해 현장시험을 수행하였으며 수치해석을 수행하여 현장시험과 비교하였다. 현장시험은 지반내 인위적인 공동을 만들기 위해 얼음을 이용하였으며, 시간경과에 따른 얼음의 융해로 인해 공동형성과 주변지반의 이완을 확인할 수 있었다. 다짐된 토사의 interlocking에 의한 이완 및 공동형성 거동을 고려하기 위하여개별요소법에 근거한 수치해석 프로그램인 PFC 2D를 이용하였다. PFC의 클럼프(clump) 요소를 도입하여 불규칙 형상의 입자를 모사하였으며, 이를 통해 얻은 공동형성과 지반이완 특성을 현장시험 결과와 비교함으로써 지반내 공동형성 및 거동특성을 파악하였다.

• 한국지반환경공학회 논문집
• /
• 제18권12호
• /
• pp.5-11
• /
• 2017

농촌 비닐하우스에서 배출되는 폐비닐을 녹여 19mm 크기의 골재를 만들었다. 이것을 아스콘에 몇몇 중량비로 혼합한 후 단열효과시험, 동결융해 후 인장강도시험, 빙착인장강도시험 그리고 현장 밀도시험을 각각 실시하였다. 그 결과 폐비닐골재는 내부에 공극을 다수 포함하고 있는 관계로 폐비닐골재 혼합율이 증가할수록 단열효과가 증가하였다. 아스콘의 동결융해 후 인장강도는 폐비닐골재 혼합율 0%일 때보다 혼합율 2.5%일 경우 크게 증가하였지만, 혼합율 5%, 10%에서는 혼합율 2.5%일 때보다 다소 감소하는 경향을 보였다. 빙착인장강도는 일반아스콘에 비해 폐비닐골재를 2.5% 추가한 아스콘에서 더 작게 나타났다. 현장 채취시료에 대한 공극률시험 결과 폐비닐골재를 추가한 아스콘의 공극률이 일반 아스콘의 그것보다 작았다.

• Geomechanics and Engineering
• /
• 제29권3호
• /
• pp.281-290
• /
• 2022

The direct shear test is commonly used to evaluate the shear behavior of frozen soil-structure interfaces under normal stress. However, failure criteria, such as the Mohr-Coulomb failure criterion, are needed to obtain the unconfined shear strength. Hence, the punch shear test, which is usually used to estimate the shear strength of rocks without confinement, was examined in this study to directly determine the adfreezing strength. It is measured as the shear strength of the frozen soil-structure interface under unconfined conditions. Different soils of silica sand, field sand, and field clay were prepared inside the steel and concrete ring structures. Soil and ring structures were frozen at the target temperature for more than 24 h. A punch shear test was then conducted. The test results show that the adfreezing strength increased with a decrease in the target temperature and increase in the initial water content, owing to the increase in ice content. The adfreezing strength of field clay was the smallest when compared with the other soil specimens because of the large amount of unfrozen water content. The field sand with the larger normalized roughness showed greater adfreezing strength than the silica sand with a lower normalized roughness. From the experiment and analysis, the applicability of the punch shear test was examined to measure the adfreezing strength of the frozen soil-structure interface. To find a proper sample dimension, supplementary experiments or numerical analysis will be needed in further research.

• 대한조선학회논문집
• /
• 제58권5호
• /
• pp.330-338
• /
• 2021

This paper focuses on the improvement of the influence coefficient matrix method for estimation of local ice load on the icebreaking research vessel ARAON. The influence coefficient matrix relates ice pressure on the hull plate to the measured/calculated hull strain/stress. Conventionally von Mises equivalent stresses representing hull stresses and ice pressure acting on the hull plate are utilized to assemble the influence coefficient matrix. Because of the three dimensional features of the ship-ice collision process, an enhanced method to assemble the influence coefficient matrix is derived considering ice loads in the X, Y, and Z direction simultaneously. Furthermore the location of ice loads acting on hull-plate may fall outside the measuring sensor area, and the enhanced influence coefficient matrix is modified to reduce the difference between the actual and the estimated ice loads by expanding the domain outward from the sensor area. The developed method for enhanced influence coefficient matrix is applied to IBRV ARAON during the 2019 Antarctic ice field test and the local ice loads in three directions are efficiently calculated compared to those by a conventional method.

• Wind and Structures
• /
• 제32권3호
• /
• pp.205-217
• /
• 2021

Cold regions with high air density and wind speed attract wind energy producers across the globe exhibiting its potential for wind exploitation. However, exposure of wind turbine blades to such cold conditions bring about devastating impacts like aerodynamic degradation, production loss and blade failures etc. A series of wind tunnel tests were performed to investigate the effect of icing on the aerodynamic properties of wind turbine blades. A baseline clean wing configuration along with four different ice accretion geometries were considered in this study. Aerodynamic force coefficients were obtained from the surface pressure measurements made over the test model using MPS4264 Simultaneous pressure scanner. 3D printed Ice templates featuring different ice geometries based on Icing Research Tunnel data is utilized. Aerodynamic characteristics of both the clean wing configuration and Ice accreted geometries were analysed over a wide range of angles of attack (α) ranging from 0° to 24° with an increment of 3° for three different Reynolds number in the order of 105. Results show a decrease in aerodynamic characteristics of the iced aerofoil when compared against the baseline clean wing configuration. The key flow field features such as point of separation, reattachment and formation of Laminar Separation Bubble (LSB) for different icing geometries and its influence on the aerodynamic characteristics are addressed. Additionally, attempts were made to understand the influence of Reynolds number on the iced-aerofoil aerodynamics.

• 한국해양공학회지
• /
• 제27권5호
• /
• pp.88-92
• /
• 2013

The icebreaking research vessel (IBRV) ARAON had her second ice trial in the Arctic Ocean in the summer season of 2010. During the voyage, the local ice loads acting on the bow of the port side were measured using 14 strain gauges. These measurements were carried out in three icebreaking performance tests. To convert the measured strains into the local ice pressures, a finite element model of the instrumented area was developed. The influence coefficient method (ICM), which uses the influence coefficient from the finite element model, and the direct method, which uses the measured strain, were selected as the conversion methods. As a result, the maximum measured pressure was 1.236MPa, and the average difference between ICM and the direct method was about 5% for an area of $0.2m^2$. The pressure-area relationship of the measurement falls below the range of the existing pressure-area curve, which is due to the low ice strength of melted ice in the summer.

• 대한치과재료학회지
• /
• 제43권4호
• /
• pp.317-322
• /
• 2016

The effect of ice-quenching after degassing on the hardness change during simulated porcelain firing in a metal-ceramic Pd-Au-Ag alloy was investigated by means of hardness test, field emission scanning electron microscopic observations, and X-ray diffraction analysis. The hardness decreased by ice-quenching after degassing, which was induced by the homogenization of the ice-quenched specimen. The decreased hardness by ice-quenching after degassing was recovered from the 1st opaque stage which was the first stage of the remaining firing process for bonding porcelain. The microstructural change showed that the increase in hardness during the remaining firing process was caused by precipitation. The ice-quenching after degassing did not affect the hardness change during the subsequent porcelain firing process.

• Structural Engineering and Mechanics
• /
• 제75권4호
• /
• pp.487-496
• /
• 2020

Most of the previous works on numerical analysis of galloping of transmission lines are generally based on the quasisteady theory. However, some wind tunnel tests of the rectangular section or hangers of suspension bridges have shown that the galloping phenomenon has a strong unsteady characteristic and the test results are quite different from the quasi-steady calculation results. Therefore, it is necessary to check the applicability of the quasi-static theory in galloping analysis of the ice-covered transmission line. Although some limited unsteady simulation researches have been conducted on the variation of parameters such as aerodynamic damping, aerodynamic coefficients with wind speed or wind attack angle, there is a need to investigate the numerical simulation of unsteady galloping of two-dimensional iced transmission line with comparison to wind tunnel test results. In this paper, it is proposed to conduct a two dimensional (2-D) unsteady numerical analysis of ice-covered transmission line galloping. First, wind tunnel tests of a typical crescent-shapes iced conductor are conducted firstly to check the subsequent quasisteady and unsteady numerical analysis results. Then, a numerical simulation model consistent with the aeroelastic model in the wind tunnel test is established. The weak coupling methodology is used to consider the fluid-structure interaction in investigating a two-dimension numerical simulation of unsteady galloping of the iced conductor. First, the flow field is simulated to obtain the pressure and velocity distribution of the flow field. The fluid action on the iced conduct at the coupling interface is treated as an external load to the conductor. Then, the movement of the conduct is analyzed separately. The software ANSYS FLUENT is employed and redeveloped to numerically analyze the model responses based on fluid-structure interaction theory. The numerical simulation results of unsteady galloping of the iced conduct are compared with the measured responses of wind tunnel tests and the numerical results by the conventional quasi-steady theory, respectively.

• Smart Structures and Systems
• /
• 제29권5호
• /
• pp.653-660
• /
• 2022

Gravel scattering that is generated during operation of high-speed railway vehicle is cause to damage of vehicle such as windows, axle protector and so on. Especially, those are frequently occurred in winter season when snow ice is generated easily. Above all, damage of vehicle windows has not only caused maintenance cost but also increased psychological anxiety of passengers. Various methods such as heating system using copper wire, heating jacket and heating air are applied to remove snow ice generated on the under-body of vehicle. However, the methods require much run-time and man power which can be low effectiveness of work. Therefore, this paper shows that large-area heating system was developed based on heating coat in order to fundamentally prevent snow ice damage on high-speed railway vehicle in the winter season. This system gives users high convenience because that can remotely control the heating system using IoT-based wireless communication. For evaluating the applicability to railroad sites, a field test on an actual high-speed railroad operation was conducted by applying these techniques to the brake cylinder of a high-speed railroad vehicle. From the results, it evaluated how input voltage and electric power per unit area of the heating specimen influences exothermic performance to draw the permit power condition for icing. In the future, if the system developed in the study is applied at the railroad site, it may be used as a technique for preventing all types of damages occurring due to snow ice in winter.