• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.11
• /
• pp.2758-2764
• /
• 2015

In the field of electronic warfare applications, high voltage power supply(HVPS) for high power phased array transmitters must necessarily have an independent operating characteristics for driving mini TWTs. TWT independent operational characteristics, in order to run without interrupting the electronic warfare mission by maintaining the partial transmission function even when one of the TWT has occurred a failure, is known to be very important. In this paper, we describe the research on high-speed independent control system using a high-density HVPS, including FE modulators, hardware configuration and the FPGA in order to independently operate mini TWTs. Also, we have simulated some possible faults in phased array transmitters, and presents the test results to control a faulted TWT independently.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.4
• /
• pp.15-22
• /
• 2019

The use of modular buildings is increasing because of various advantages of modular buildings. But there are limits to apply modular buildings to medium-rise buildings because the building law provides only the specification criteria of the modular building with respect to the 1 hour fire resistance performance. This study was conducted to investigate 2 hours fire resistance performance of load bearing walls with steel studs in modular buildings by KS F 2257-1 and KS F 2257-4. After full scale tests, load bearing walls ensuring two hours fire resistance performance consist of at least 2 layers of fire resistance plaster boards of 19mm thickness or 3 layer of fire resistance plaster boards of thickness.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.53-53
• /
• 2023

본 연구에서는 토양의 동결-융해 상태 구분을 위해 영상레이더(Synthetic Aperture Radar) 자료를 활용해 지표상태인자(Surface State Factor, SSF)를 산정하고, 관측 토양수분 자료 및 지표면 온도(Land Surface Temperature, LST) 자료와의 비교를 통해 SSF의 정확도를 분석하였다. SSF 산정은 용담댐 유역을 포함한 인근 40×50 km²의 영역(N35°35'~36°00', E127°20'~127°45')에 대한 9개의 토양수분 관측지점(계북, 천천, 상전, 안천, 부귀, 주천, 장수읍, 진안읍, 무주읍)을 대상으로 연구를 수행하였으며, 이를 위해 2015년부터 2019년까지의 해당 지점의 토양수분 관측자료와 Sentinel-1A Interferometric Wide swath (IW) 모드의 Ground Range Detected (GRD) product를 구축하여 활용하였다. SSF 자료의 정확도 분석을 위한 토양수분 관측지점에 대한 LST 자료는 인근 7개 기상관측소 지점(전주, 금산, 임실, 남원, 장수, 함양군, 거창)의 관측자료로부터 역거리가중법을 통해 산정하였다. Receiver Operating Characteristic (ROC) 분석을 통한 겨울철(12-2월)의 SSF 산정 정확도를 평가한 결과, 지표면 온도 자료와의 평균 정확도는 0.75(0.48-0.87)로 나타났다. 그러나, 지표면 온도가 0℃ 이상일 때 SSF가 동결 상태로 나타나는 오차가 관측되었으며, 이는 여름철 후방산란계수의 평균값과 겨울철 후방산란계수의 평균값을 통해 산정하는 SSF 산정 수식의 특성 때문으로 이 값의 조정을 통해 오차를 개선할 수 있음을 보였다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.161-161
• /
• 2021

본 연구에서는 금강 상류의 용담댐 유역(930.0 km²)을 대상으로 Sentinel-1 SAR(Synthetic Aperture Radar) 및 Sentinel-2 MultiSpectral Instrument(MSI) 위성영상을 활용한 토양수분 산출연구를 수행하였다. 연구에 사용된 자료는 10 m 해상도의 Sentinel-1 IW(Interferometric Wide swath) mode GRD(Ground Range Detected) product의 VV(Vertical transmit-Vertical receive) 및 VH(Vertical transmit-Horizontal receive) 편파자료와 Sentinel-2 Level-2A Bottom of Atmosphere(BOA) reflectance 자료를 2019년에 대해 각 6일 및 5일 간격으로 구축하였다. 위성영상의 Image processing은 SNAP(SentiNel Application Platform)을 활용하여 Sentinel-1 영상의 편파 별(VV, VH) 후방산란계수와 Sentinel-2의 적색(Band-4) 및 근적외(Band-8) 영상을 생성하였다. 토양수분 산출 모형은 다중선형회귀모형(Multiple Linear Regression Model)을 활용하였으며, 각 지점에 해당하는 토양 속성별로 모형을 생성하였다. 모형의 입력자료는 Sentinel-1 위성의 편파별 후방산란계수, Sentinel-1 위성에서 산출된 식생지수 RVI(Radar Vegetation Index)와 Sentinel-2 위성에서 산출된 NDVI(Normalized Difference Vegetation Index)를 활용하여 식생의 영향을 반영하고자 하였다. 모의 된 토양수분을 검증하기 위해 6개 지점의 TDR(Time Domain Reflectometry) 기반 실측 토양수분 자료를 수집하고, 상관계수(Correlation Coefficient, R), 평균제곱근오차(Root Mean Square Error, RMSE) 및 IOA(Index of Agreement)를 활용하여 전체 기간 및 계절별로 나누어 검증할 예정이다.

• Korean Journal of Food Science and Technology
• /
• v.49 no.3
• /
• pp.304-310
• /
• 2017

The aim of this study was to compare the physicochemical properties of domestic and imported commercial plain wheat flour and dough. Four types of domestic wheat flour (DW; DW1-4) were compared to four types of imported wheat flour (IW; IW1-4). DWs exhibited lower moisture content, lightness (L), and whiteness, and higher protein content, redness (a), and yellowness (b), than those exhibited by IWs. Solvent retention capacity of DWs and IWs was similar; however, DWs showed higher gluten performance index. Pasting properties, analyzed by rapid visco analyzer (RVA), were similar for DW1, DW2, and IWs; however, DW3 and DW4 showed different RVA patterns. Considering that DW3 and DW4 were organic wheat flour, possible incorporation of damaged kernel might increase amylase activities resulting in decreased peak viscosity. Dough resistance (108.4-159.9 g) and extensibility (11.8-16.7 mm) of IWs were higher than those of DWs (78.0-118.7 g, 8.7-12.5 mm, respectively).

• Nuclear Engineering and Technology
• /
• v.22 no.4
• /
• pp.337-350
• /
• 1990

A post-irradiation annealing study was conducted with use of reactor pressure vessel(RPV) steel A533B Cl.1 base metal irradiated to a dose of 4.84$\times$10$^{18}$ n/$\textrm{cm}^2$ at about 38$0^{\circ}C$. Microhardness and positron annihilation (PA) methods were used to obtain better understanding of the recovery of radiation hardening. Isochronal anneal experiments indicated that two recovery processes occur during annealing of irradiated specimens. The first recovery process occurs in the temperature range of 280-3O5$^{\circ}C$, Michrohardness and positron annihilation (PA) methods were used to obtain better understanding of the recovery of radiation hardening. Isochronal anneal experiments indicated that two recovery processes occur during annealing of irradiated specimens. The first recovery process occurrs in the temperature range of 280-305$^{\circ}C$. The variations of Ip, Iw and R parameters indicated that the formation of vacancy clusters by vacancy agglomeration and the annihilation of monovacancies are the first recovery process. The second recovery process occurs in the range of 405-49$0^{\circ}C$ and positron annihilation parameters measured indicated that the dissolution of carbon atoms decorated around vacancy-type defects and possible precipitates, and the annihilation of monovacancies give rise to the second recovery process. It was further indicated that radiation anneal hardening (RAH) in the range of 305-405$^{\circ}C$ between the temperature ranges for the two processes occurs due to the formation of carbon-decorated vacancy clusters and precipitates. The activation energies, orders of reaction and other characteristics of recovery processes were determined by the Meechan-Brinkman method. The activation energy for the first recovery process was determined as 1.76 eV and that for the second recovery process as 2.00eV. These values are lower than those obtained by other workers. This difference may be attributed to the lower copper content of the RPV steel used in the present study. The order of reaction for the first recovery process was determined as 1.78, while that for the second recovery process as 1.67 Non-integer orders of reaction for recovery processes seem to be attributed to the fact that several mechanisms for the first order and the second order of reaction are compounded in one process. This result also supports for the above conclusions from measurements of PA parameters.

• Journal of Korea Water Resources Association
• /
• v.55 no.12
• /
• pp.1125-1135
• /
• 2022

Damages by heavy snow does not occur very often, but when it does, it causes damage to a wide area. To mitigate snow damage, it is necessary to know, in advance, the depth of snow that causes damage in each region. However, snow depths are measured at observatory locations, and it is difficult to understand the spatial distribution of snow depth that causes damage in a region. To understand the spatial distribution of snow depth, the point measurements are interpolated. However, estimating spatial distribution of snow depth is not easy when the number of measured snow depth is small and topographical characteristics such as altitude are not similar. To overcome this limit, satellite images such as Synthetic Aperture Radar (SAR) can be analyzed using Differential Interferometric SAR (DInSAR) method. DInSAR uses two different SAR images measured at two different times, and is generally used to track minor changes in topography. In this study, the spatial distribution of snow depth was estimated by DInSAR analysis using dual polarimetric IW mode C-band SAR data of Sentinel-1B satellite operated by the European Space Agency (ESA). In addition, snow depth was estimated using geostationary satellite Chollian-2 (GK-2A) to compare with the snow depth from DInSAR method. As a result, the accuracy of snow cover estimation in terms with grids was about 0.92% for DInSAR and about 0.71% for GK-2A, indicating high applicability of DInSAR method. Although there were cases of overestimation of the snow depth, sufficient information was provided for estimating the spatial distribution of the snow depth. And this will be helpful in understanding regional damage-causing snow depth.

• The Korean Journal of Ceramics
• /
• v.4 no.2
• /
• pp.95-98
• /
• 1998

We have developed new type of superconducting-superionic conducting nanohybrids, $Ag_xI_wBi_2Sr_2Ca_{n-1}Cu_nO_y$ (n=1 and 2) by applying the chimie douce reaction to the superconducting Bi-based cuprates. These nanohybrids can be achieved by the stepwise intercalation whereby the $Ag^+$ ion is thermally diffused into the pre-intercalated iodine sublattice of $IBi_2Sr_2Ca_{n-1}Cu_nO_y$. According to the X-ray diffraction analysis, the Ag-I intercalates are found to have an unique heterostructure in which the superionic conducting Ag-I layer and the superconducting $IBi_2Sr_2Ca_{n-1}Cu_nO_y$ layer are regularly interstratified with a remarkable basal increment of ~7.3$\AA$. The systematic XAS studies demonstrate that the intercalation of Ag-I accompanies the charge transfer between host and guest, giving rise to a change in hole concentration of $CuO_2$ layer and to a slight $T_c$ change. The Ag K-edge EXAFS result reveals that the intercalated Ag-I has a $\beta$-AgI-like local structure with distorted tetrahedral symmetry, suggesting a mobile environment for the intercalated $Ag^+$ ion. In fact, from ac impedance analyses, we have found that the Ag-I intercalates possess a fast ionic conductivity ($\sigma_i=10^{-1.4}\sim 10^{-2.6}\Omega^{-1}\textrm{cm}^{-1}\;at\;270^{\circ}C$ with an uniform activation energy ($\DeltaE_a=0.22\pm 0.02$ eV). More interesting finding is that these intercalates exhibit high electronic conducting as well as ionic ones ($t_i$=0.02~0.60) due to their interstratified structure consisting of superionic conducting and superconducting layers. In this respect, these new intercalates are expected to be useful as an electrode material in various electrochemical devices.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.1
• /
• pp.24-36
• /
• 2003

The digital mobile communication will be developed till getting multimedia service in anyone, any where, any time. Theses requiring items are going to be come true via IMT-2000 system. Transmitting signal bandwidth of IMT-2000 system is 3 times as large as IS-95 system. That is mean peak to average of signal is higher than IS-95A system. So we have to design it carefully not to effect in adjacent channel. HPA(High Power Amplifier) located in the end point of system is operated in 1-㏈ compression point(Pl㏈), then it generates 3rd and 5th inter modulation signals. Theses signals affect at adjacent channel and RF signal is distorted by compressed signal which is operated near by Pl㏈ point. Then the most important design factor is how we make HPA having high linearity. Feedback, Pre-distorter and Feed-forward methods are presented to solve theses problems. Feed-forward of these methods is having excellent improving capacity, but composed with complex structure. Generally, Linearity and Efficiency in power amplifier operate in the contrary, then it is difficult for us to find optimal operating point. In this paper we applied algorithm which searches optimal point of linear characteristics, which is key in Power Amplifier, using minimum current point of error amplifier in 1st loop. And we made 2nd loop compose with new structure. We confirmed fabricated LPA is operated by having high linearity and minimum current condition with ACPR of -26 ㏈m max. @ 30㎑ BW in 3.515㎒ and ACLR of 48 ㏈c max@${\pm}$㎒ from 1W to 40W.

• Journal of Navigation and Port Research
• /
• v.36 no.5
• /
• pp.329-338
• /
• 2012

The Institute Time Clauses-Hulls 1/10/83 has been using widely with attachment and/or endorsement of the Institute Warranties 1/7/76 stipulating vessel's trading limits. Taking into consideration of several changes and renewals on the contents of the Institute Time Clauses-Hulls for clarifying the clauses themselves with development on technology of vessel's construction and navigational equipments up to the present, the clauses on the Institute Warranties 1/7/76 should have been changed and/or renewed. Moreover, the insured still has been burdening additional premium in vessel's navigating and / or calling to the areas stipulated in the Institute Warranties 1/7/76 regardless of any changes of marine business environments. Thus, this study aims to analyze the Institute Warranties 1/7/76 as well as to suggest a reasonable level of additional premium for breach of Institute warranties through not only a comparative analysis between the Institute Warranties clauses and those of the corresponding Institute Warranties using in the Japanese Fire and Marine Insurance companies but also consideration of current circumstances on changes in climatic conditions, vessel design, navigation and communication requirements and capabilities.