• Journal of the Korean Vacuum Society
• /
• v.9 no.1
• /
• pp.30-35
• /
• 2000

Indium-Tin Oxide (ITO) thin films were deposited on the commercial glass substrate by rf-magnetron sputtering. The ITO films with the thickness of 2,000~2,400 $\AA$ were prepared by changing the oxygen partial pressures of 2, 3, and 5%, as well as by changing the substrate temperature of $300^{\circ}C$ and $500^{\circ}C$. spectrophotometer, XRD, SEM, AFM, 4-point probe and Hall effect system were employed to characterize the ITO films. The optimum deposition conditions were the substrate temperature of $500^{\circ}C$ and oxygen partial pressure of 2-3%. At theses conditions, the ITO film showed the transmittance of 91%, the resistivity of $5.4\times10^{-3}\Omega$cm, the carrier concentration of $1.0\times10^{19}\textrm{cm}^{-3}$, and the carrier mobility of 150$\textrm{cm}^2$/Vsec. In XRD spectra, the (222) and (400) $In_2O_3$ planes were dominant under the optimum deposition conditions When the substrate was cleaned only by the method of ultrasonic cleaning without both pre-annealing and chemical treatment of the substrate, the ITO film exhibited the transmittance of 86%, the carrier concentration of $5.4\times10^{19}\textrm{cm}^{-3}$ and the mobility of 24$\textrm{cm}^2$/Vsec.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.321-323
• /
• 2012

유기 발광 다이오우드는(OLEDs) 자체 발광 소자로써 높은 시야각, 높은 효율, 그리고 빠른 응답속도 등의 장점을 가지고 있어 차세대 디스플레이 및 조명 소자로서 많은 연구가 진행되고 있다. 특히 유기 발광 다이오우드는 차세대 반도체 조명 소자로서 조명의 패러다임을 바꿀 수 있는 기술로 인식되고 있다. 하지만, 유기 발광 다이오우드 조명의 상용화를 위해서는 가격 경쟁력을 갖추는 것이 시급하며, 이를 위해 저가 공정 개발이 필요하다. 본 연구에서는 유기발광 다이오우드 조명 제작에 필수적인 전면 전극 및 절연막 증착 공정을 기존의 노광 공정이 아닌 shadow mask 기술을 적용하여 형성하였다. 먼저 유리 기판 상에 150 nm 두께의 ITO 막을 shadow mask를 이용하여 증착하였다. 기존 공정에서는 노광 및 식각 공정을 이용하여 증착하는 것이 일반적이며, 광학적, 전기적 특성 또한 타 공정 방법에 비해 우수하다. 하지만 일련의 복잡한 공정으로 인해 제조 원가를 상승 시키는 단점이 있다. Fig. 1은 shadow mask를 이용하여 ITO를 증착을 수행한 공정의 모식도이다. ITO 박막 증착 후 표면 거칠기 제어 및 면저항 제어를 위해 O2 plasma 처리와 RTA 공정을 추가 수행하였다. Fig. 2(a)는 플라즈마 처리 및 열처리 공정 수행 후에 측정한 표면 AFM 사진이다. 열처리 및 플라즈마 처리 후에 ITO 박막의 표면 거칠기는 10배 이상 향상되었으며, 이는 유기 발광 다이오우드 조명 소자의 전면 투명 전극으로 사용되기에 적합한 값이다. 또한 전기적 특성 중 하나인 면저항 값은 열처리 및 플라즈마 처리 전/후의 값에서 많은 차이를 보인다. 표면 거칠기가 향상됨에 따라 면저항 값 역시 향상되는 결과를 보여주는데, 표면 처리전후의 면저항 값은 각각 28.17, 13.18 ${\Omega}/{\Box}$이다. 일반적으로 유기 발광 다이오우드의 전면 투명 전극으로 사용되기 위해서는 15 ${\Omega}/{\Box}$이하의 면저항 값이 필요한데, 표면 처리 후의 면저항값들은 이로한 조건을 만족한다. Fig. 3은 shadow mask 기술을 이용하여 절연막까지 형성한 유기 발광 다이오우드 소자의 전자 현미경 사진으로, 기존의 공정을 이용한 경우와 큰 차이는 없으며, 다만 shadow tail이 약 $30{\mu}m$ 정도 발생함을 확인할 수 있다. 절연막의 특성 평가 기준인 누설 전류 밀도는 $10-5A/cm^2$으로 기존의 공정을 이용한 경우에 비해 95% 수준으로서 shadow mask를 이용한 공정이 기존의 노광 및 식각 공정을 이용한 경우에 비해 공정 수는 9개가 단축됨에도 불구하고, 각 증착 박막의 특성에는 큰 차이가 없음을 알 수 있다.

• Applied Chemistry for Engineering
• /
• v.17 no.6
• /
• pp.591-596
• /
• 2006

Topology and molecular ordering of NPD(4,4'-bis-[N-(1-naphthyl)-N-phenyl-amino]biphenyl) thin films deposited under magnetic field with post-deposition annealing were investigated. NPD was deposited onto ITO glass substrates via thermal evaporation process in vacuum. It is of great importance for highly oriented organic/metal films to have improved device performances such as higher current density and luminance efficiency. AFM (Atomic Force Microscope) and XRD (X-Ray Diffraction) analyses were used to characterize the topology and structure of oriented NPD films. The multi-source meter was used to observe the current-voltage characteristics of the ITO (Indium-Tin Oxide) / NPD (4,4'bis[N-(1-napthyl)-N-phenyl-amino]-biphenyl) / Al (Aluminum) device. While NPD thin films deposited under magnetic field were not molecularly well aligned according to the XRD results, the films after post-deposition annealing at $130^{\circ}C$ were well-oriented. AFM images show that NPD thin films deposited under magnetic field had a smoother surface than those deposited without magnetic field. The current-voltage performance of NPD thin films was improved due to the enhanced electron mobility in the well-aligned NPD films.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.7
• /
• pp.563-568
• /
• 2012

Indium tin oxide (ITO) films were prepared using radio frequency (RF) magnetron sputtering method, magnets were equipped near the target in the sputter to bring the plasma near the target. The effect of magnetic field that brings the plasma near the substrate was compared with that of substrate heating. The effect of substrate heating on the grain size of the ITO thin film was larger than that of the magnetic field. However, the grain size of the ITO thin film was larger when the magnetic field was applied near the substrate during the sputtering process than when the substrate was not heated and the magnetic field was not applied. If stronger magnetic field is applied near the substrate during sputtering, it can be expected that the ITO thin film with good electrical conductivity and high transparency is obtained at low substrate temperature. When magnetic field of 90 Gauss was applied near the substrate during sputtering, the mobility of the ITO thin film increased from 15.2 $cm^2/V.s$ to 23.3 $cm^2/V.s$, whereas the sheet resistivity decreased from 7.68 ${\Omega}{\cdot}cm$ to 5.11 ${\Omega}{\cdot}cm$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.316-316
• /
• 2008

Using an evaporation method, $SiO_2$ was deposited as a buffer layer between a flexible PET substrate and a ITO film deposited by DC magnetron sputtering and electro-optical properties were investigated with thickness variance of $SiO_2$ layers. After coating a $SiO_2$ layer and a ITO film, the ITO/$SiO_2$/PET was heated up to $200^{\circ}C$ and the resistivity and the transmittance were measured by hall effect measurement system and UV/VIS/NIR spectroscopy. As a result of depositing a $SiO_2$ buffer layer, the resistivity increased and the transmittance and adhesion property were enhanced than ITO films with no buffer layers and the resistivity was lowered as $SiO_2$ thickness increased from 50 $\AA$ to 100 $\AA$. It was found that the transmittance was independent of annealing temperature variance in $150^{\circ}C{\sim}200^{\circ}C$ and the resistivity decreased as the temperature increased and especially decreasing rate of the resistivity was higher as the buffer layer thickness was thinner. So under optimized depositing of $SiO_2$ buffer layers and post-annealing of ITO/$SiO_2$/PET, ITO films with enhanced adhesion, electro-optical properties can obtained.

• Journal of Surface Science and Engineering
• /
• v.40 no.3
• /
• pp.117-124
• /
• 2007

The ITO films were deposited on glass substrates by RF-superimposed dc reactive magnetron sputtering and were annealed in $N_2$ vacuum furnace with temperatures in the range of $403K{\sim}573K$ for 30 minutes. Electrical, optical and structural properties of ITO films were examined with varying annealing temperatures from 403 K to 573 K. The resistivity of as-deposited ITO films was $5.4{\times}10^{-4}{\Omega}cm$ at the sputter conditions of applied RF/DC power of 200/200 W, $O_{2}$ flow of 0.2 seem and Ar flow of 0.2 seem. As a result of annealing in the temperature range of $403K{\sim}573K$, the crystallization occurred at 423 K that is lower than the crystallization temperature caused by a conventional sputtering method. And the resistivity decreased from $5.4{\times}10^{-4}{\Omega}cm\;to\;2.3{\times}10^{-4}{\Omega}cm$, the carrier concentration and mobility of ITO films increased from $4.9{\times}10^{20}/cm^3\;to\;6.4{\times}10^{20}/cm^3$, from $20.4cm^2/Vsec\;to\;41.0cm^2/Vsec$, respectively. The transmittance of ITO films in visible became higher than 90% when annealed in the temperature range of $423K{\sim}573K$. High quality ITO thin films made by RF-superimposed dc reactive magnetron sputtering and annealing in $N_2$ vacuum furnace will be applied to transparent conductive oxides of the advanced flat panel display.

• Journal of Sensor Science and Technology
• /
• v.31 no.2
• /
• pp.85-89
• /
• 2022

We investigated a pH sensor using an Indium tin oxide (ITO) nanoparticle (NP) film printed on a flexible substrate. First, the printing precision and mechanical stability of the ITO-printed film were investigated. In particular, the factors that influence the crystallinity of ITO films were studied using X-ray diffraction pattern analysis. The response of the ITO pH sensor was calibrated using a series of standard pH solutions (pH 3-11). The pH values of various specimens were measured using an ITO pH sensor, and the results were compared with those of various pH measurement methods. As a result of the experiment, the maximum error was approximately ± 0.04 pH (0.4 %) at pH 9, which indicated that the ITO pH sensor is highly suitable for pH measurement. Finally, we used the ITO pH sensor to the measure of general specimens such as solvents and beverages and compared the results in comparison with those obtained from several conventional methods.

• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.3
• /
• pp.1-6
• /
• 2007

In this study, the pentacene thin films were prepared by the soluble process, and characterized fur the application of the organic thin film transistor(OTFT) device. To dissolve the pentacene material, two kinds of solvents such as toluene and chloroform were used, and the effects of these solvents on the properties of pentacene thin films coated on ITO/Glass substrate were investigated. Pentacene thin films were prepared by using spin-coating methode and characterized the surface morphology, crystalline and electrical properties. From the AFM measurement, the surface morphology of the pentacene film dissolved with chloroform was improved compared with the one dissolved with toluene solvent. XRD measurement showed that all prepared pentacene film samples were amorphous crystal phases without crystallization of the films. The electrical properties of the pentacene film dissolved with chloroform showed better results than the ones using toluene solvent by hall measurement system. The carrier concentration and the mobility values of pentacene films using chloroform solvent were found to be $-3.225{\times}10^{14}\;cm^{-3}$ and $3.5{\times}10^{-1}\;cm^2{\cdot}V^{-1}{\cdot}S^[-1}$, respectively. The resistivity was about $2.5{\times}10^2\;{\Omega}{\cdot}cm$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.1
• /
• pp.111-116
• /
• 2006

In this paper, the image sensor using the a-Si:H TFT is proposed. The optimum amorphous silicon thin film is deposited using plasma enhanced chemical vapor deposition (PECVD). TFT and photodiode both with the thin film are fabricated and form image sensor. The photodiode shows that Idark is $10^{-12}A$, Iphoto is $10^{-9}A$ and Iphoto/Idark is $10^3$, respectively. In the case of a-Si:H TFT, it indicates that Ion/Ioff is $10^6$, the drain current is a few ${\mu}A$ and Vth is $2\~4$ volts. For the analysis on the fabricated image sensor, the reverse bias of -5 voltage in ITO of photodiode and $70{\mu}sec$ pulse in the gate of TFT are applied. The image sensor with good property was conformed through the measured photo/dark current.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.6
• /
• pp.272-278
• /
• 2003

$Bi_4Ti_3O_{12}$ (BIT) and $(Bi_{3.25}La_{0.75})(Ti_{2.97}V_{0.03})O_{12}$ (BLTV) thin films were deposited on ITO/glass substrates by metal organic chemical vapor deposition (MOCVD) using ultrasonic spraying. After deposition of the films in oxygen atmosphere for 30 min, the films were heated by rapid thermal annealing (RTA) method, especially direct insertion, at various temperatures. The films were investigated on phase formation temperature, microstructure and electrical properties. From x-ray diffraction (XRD) patterns, the perovskite phase formation temperature of BLTV thin film was about $600^{\circ}C$ which was lower than that of BIT, $650^{\circ}C$. The leakage current of the BLTV thin film was measured to be $1.52\times 10^{-9}$A/$cm^2$ at an applied voltage of 1 V. The remanent polarization (Pr) and coercive field (Ec) values of the BLTV film deposited at $650^{\circ}C$ were $5.6\muC/cm^2$ and 96.5 kV/cm, respectively.