• Journal of the Korea Concrete Institute
• /
• v.18 no.2 s.92
• /
• pp.189-198
• /
• 2006

The composition of most engineering materials is heterogeneous at some degree. It is simply a question of scale at which the level of heterogeneity becomes apparent. In the case of cementitious granular materials such as concrete the heterogeneity appears at the mesoscale where it is comprised of aggregate particles, a hardened cement paste and voids. Since it is difficult to consider each separate particle in the topological description explicitly, numerical models of the meso-structure are normally confined to two-phase matrix particle composites in which only the larger inclusions are accounted for. 2-D and 3-D concrete blocks(Representative Volume Element, RVE) are used to simulating heterogeneous concrete meso-structures in the form of aggregates in the hardened mortar with nearly zero-thickness linear or planar interfaces. The numerical sensitivity of these meso-structures are Investigated with respect to the different morphologies of heterogeneity and the different level of coupling constant among fracture mode I, II and III. In addition, a numerically homogenized concrete block in 3-D using Hashin-Shtrikman variational bounds provides an evidence of the effective cracking paths which are quite different with those of heterogenous concrete block. However, their average force-displacement relationship show a pretty close match each other.

• Journal of Korea Foundry Society
• /
• v.35 no.4
• /
• pp.67-74
• /
• 2015

In this study, Mg-Zn alloys are investigated in terms of their thermal properties after an addition of Cu. Al element is added to improve the mechanical properties and castability in general case. However, it was excluded here because it significantly decreases the thermal conductivity. On the other hand, Zn was added as a major element, which had less influence on reducing the conductivity and can complement the mechanical properties as well. Cu was also added, and it improved the heat transfer characteristics as the amount was increased. The composition ranges of Zn and Cu are 6 wt.% and 0~1.5 wt.%, respectively. Mg-6Zn-xCu alloy was prepared by a gravity casting method using a steel mold and then the thermal conductivity and the microstructure of the as-cast material were investigated. By measuring the density_(${\rho}$), specific heat_(Cp) and thermal diffusivity_(${\alpha}$), the thermal conductivity_(${\lambda}$) was calculated by the equation ${\lambda}={\rho}{\cdot}Cp{\cdot}{\alpha}$. As the amount of Cu increased in the Mg-6Zn-xCu alloy, the heat transfer characteristics were improved, resulting in a synergistic effect which is slow when the added Cu exceeds 1 wt.%. In order to investigate the relative thermal conductivity/emission of the Mg-6Zn-xCu alloy, AZ91 and AZ31 were experimentally evaluated and compared using a separate test equipment. As a result, the Mg-6Zn-1.5Cu alloy when compared to AZ91 showed improvements in the thermal conductivity ranging from 30 to 60% with a nearly 20% improvement in the thermal emission.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.5
• /
• pp.98-107
• /
• 2016

An analytical comparison of a synthetic memristor emulator and a M-R mutator-based memristor emulator has been performed. Memristor is an electrical element with the characteristic of variable resistance. It is called the fourth fundamental electrical element following resistor, capacitor, and inductor. Memristor emulator is a circuit which implements the feature of variable resistance via the composition of various electrical devices. It is an essential circuit to study memristor characteristics during the time before it is commercially available. There are two representative memristor emulators depending upon their implementation methods. One is a memristor emulator which is synthesized via combining various electrical devices and the other one is M-R mutator-based memristor emulator implemented by extracting resistance from a nonlinear device. In this paper, implementation methods of these two memristor emulators are studied and their differences are investigated by analysing their characteristics.

• Proceeding of Spring/Autumn Annual Conference of KHA
• /
• 1994.05a
• /
• pp.57-63
• /
• 1994

The purpose of this study is to examine how Korean changed and applied the railway official residence space constructed by the Japanese, when they occupied these railway official residence space after liberation from Japan, and specify the relationship between the life culture and residence space by analysing the differance in important life style, as well as element of change in important residence spaces according to modernization. In addition, this study was carried out by means of research on the form and pattern, visual anthropological method by photograph and direct observation.The result of this study is summarized as fellows. The residence space at Kyounaju constructed by the Japanese on the basis of the culture has been changed and applied to the life style of the Korean when the Korean occupied these Japanese style residence space.Then, it seems that the change of the Japanese style residence was caused by both differance in the life pattern between Korea and Japan, and the medernization of the life.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.290-295
• /
• 2002

This research has been carried out to experiment machining characteristics by elements addition and subtraction of AC8B and sample that is used fur car piston materials. 1.Mechanical properties of development sample expressed unique mechanical properties than AC8B. 2. Cutting resistance of development sample decreased about 10% than AC8B according to increase of the cutting speed. 3. According to increase of the feedrate, all comparison workpiece found that specific cutting resistance decrease. 4. It was found that sample's machining characteristics that is developed by addition and subtraction of elements improves.

• 보존과학연구
• /
• s.29
• /
• pp.111-124
• /
• 2008

Gold case which is called sarari container was excavated from Wangheungsaji of Buyeo in October 2007. This case did not contain sarira, but was filled with clear liquid. This study focused on component analysis of the liquid which had filled sarira container, because we didn't know if this case had not originally contained sarira or not. It is said that original sarira can be melted by a some liquid in this case. So, many kinds of samples which are liquid, soil and ground water, was collected from a inner and outer of sarira container, and analyzed using a IC, ICP-MS, GC-MS and SEM-EDS. As a result of analysis, all of the elements composition was identified by general components of soil and ground water. Especially, phosphate which is chemical element to consist of human bone, did not found in this liquid.

• Journal of Korea Foundry Society
• /
• v.7 no.3
• /
• pp.192-198
• /
• 1987

Commercial semicontinuous cast ingots of aluminum alloys often exhibit large grains composed of parallel arrays of continuous lamellae. Each lamella consists of a central {111} coherent twin boundary and wavy solidification boundary. This microstructure is referred to as a twin columnar growth(TCG) structure. The factors influencing the formation of a TCG structure include a unidirectional thermal gradient and the critical range of the alloying element content. The higher the thermal gradient is, the shorter the twin plane spacings are. The composition profile for an untwinned dendrite shows maximums at the positions of the interdendritic channels and the minimum appears at the center of the dendrite. While for twinned dendrite, it has wavy apperance. This profile has two local minimums instead of one shown in the untwinned.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.5 s.182
• /
• pp.137-142
• /
• 2006

The muffler which reduce the exhaust noise and vibration from engine influence on the engine performance. Recently, exhaust variable valve has set up in the muffler controls the backpressure in the exhaust system. And the backpressure variation according to the exhaust variable valve opening has developed the engine performance. First, the preceding of structural analysis is needed and simulation experiment is requested for the study on the design factor to influence on the operation of the exhaust variable valve. In this study, setting up the various variables according to each composition element needed for the structural analysis of the exhaust variable valve, it is experimented the analysis on the influence of each design factor with the calculation of stress distribution and the displacement to cause about the backpressure for the valve through parameter study.

• Proceedings of the Korean Institute of Interior Design Conference
• /
• 2004.11a
• /
• pp.140-143
• /
• 2004

The move from steel tubes to bent wood and the 'laboratory experiments' with wood which Aalto carried out in order to create furniture gave him vital impulses as he sought and found his own architecture style in the 1930s. Like his architecture Aalto's chair designs represent a 'humanized' interpretation of the severe aesthetic and radical technological experimentation of the Modern Movement. The purpose of this study is to find what is the result of the form of his works on the basis of main idea and tend of his works, to search the element and principle of formal composition, to establish the relation-ship between the architect's philosophy and the form of his works. Aalto's furniture, constructed of laminate bent wood or moulded plywood, is not only functionalistic, but also ideal for the psychological need of the people, which is the special quality that complements the Factionalism that features mostly on the metal tube furniture. It shows that Aalto is a humanist dealing with mechanized age.

• Proceedings of the KSR Conference
• /
• 2003.05a
• /
• pp.315-320
• /
• 2003

Selecting a railroad line requires the comparative evaluation of various elements. As a systematic approach to this selection it will be necessary to apply the VE study and the LCC analysis. This study proposes a methodology for selecting the optimum line of the ralroad using VE-LCC analysis. The VE study is performed by following four steps : Information analysis, Function analysis, Alternative evaluation, and Optimum plan selection. The economics evaluation in VE study is using LCC analysis and Sensitivity analysis. Cost items in LCC analysis are classified into bridge, tunnel, rail, and earthwork. We could select the optimum alte-rnatives considering not only cost elements hut also various evaluation element in VE-LCC analysis. The synthetic evaluation process of relative value composition and weighted matrix evaluation