• Fashion & Textile Research Journal
• /
• v.9 no.4
• /
• pp.441-444
• /
• 2007

For the purpose of application to new natural dyestuff, the dyeability of Purple onion shell extract was analyzed. It was dyed in cotton fabric according to various dye weight, dyeing temperature, dyeing time. And the effects of mordanting conditions were examined as color differences and color fastnesses. The dyeaffinities were increased as were increased dye weight, especially 100% owf. The optimum dyeing condition of Purple onion shell extract was 40minutes at $60^{\circ}C$. The dyeaffinity was increased at pre-mordanted condition, and color difference was increased distinctly at post mordanted condition. The hue of all mordanted cotton fabrics changed into Yellow where as non mordanted cotton fabric was Red. The color fastnesses of mordanted cotton fabrics were generally not so god, but light fastness was improved in post-Cu mordanted fabric.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.03a
• /
• pp.19-30
• /
• 1995

The analysis had been already completed to detect forming defects for the forming processes of C/R bearing rings. But some unpredicted problems were found through the experiments. So expert redesigned new forming processes to prevent the problems and new analysis was began according to the new processes to find faults for the processes. The forming processes consist of 1 for the outer ring. 6 inner ring. The thickness of metal sheet used is changed to 1.5mm from 1.6mm. Elasto-plastric finite element method is applied to involve the effect of spring back . The most representative alteration is forming of two predents to assist later forming . Thining and distribution of high residual stress are derived from the results of simulations. It is confirmed that the industry expert agree the possiblilty of defects dervied from the new FEM results.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.535-540
• /
• 2003

In this Paper, a LON based distributed control system for HVAC is described. We developed multi-protocol converter based on SoC, Neuron Chip, embedded Linux. It utilizes the network environment and therefore requires an appropriate operating system for handling protocols and an advanced development environment. The open source licensing, reliability, and broad hardware support are key reasons for use of embedded Linux in embedded industry. The multi-prootocol converter integrates LonWorks devices to a client with Java applet. The system consists of three-tier architecture, such as clients, multi-protocol converter, and LonWorks devices. The experiment result show that multi-protocol converter using embedded Linux is a flexible and effective way to build a Web-based monitoring and control system.

• International conference on construction engineering and project management
• /
• 2011.02a
• /
• pp.12-16
• /
• 2011

Building Information Modeling (BIM) is being widely spread in AEC industry worldwide and also in South Korea. Although the creation of digital model is better to be started at design stage, it can also improve the productivity of construction by simulating the actual construction process and environment. This paper presents application of BIM-based simulations related with design changes to transfer floors in 58-storey reinforced concrete office building. Transfer floor is not only a structurally important part of the building but also a challenging part of the actual construction in terms of sequence and period due to the complexity of the work. Preconstruction of rebar, mechanical, and plumbing is performed to review the construction drawings and to perform clash detection. Each item of application is evaluated for its effectiveness on actual construction and for the development potential.

• Journal of Ocean Engineering and Technology
• /
• v.3 no.2
• /
• pp.138-144
• /
• 1989

It has been very important in various industry fields to improve the fatigue strength characteristics of bearings such as bearing life, fatigue limit, etc., because such poor properties could result in shortening the machinery life as well as in decreasing the accuracy. However, no successful heat treatment criterion seems to be available at present. In this study, the effect of the $170^{\circ}C\times120min$ tempering cycles repeated after $380^{\circ}C\times80min$ oil quenching for $800^{\circ}C$ spheroidizing-annealed bearing steel (STB2) as base metal on the $120^{\circ}C$ high temperature rotary bending fatigue strength characteristics were investigated, including the effects on hardness, Charpy impact value and micro-structure, in order to seek for the best heat treatment condition finally. The important results obtained are as follows : 1) The optimal cycle of tempering so that the fatigue strength .sigma. could become the highest was the 4th cycle. And it is confirmed that this $\sigma_{F}$ is about 6 times more increased than that of base metal, and about 1.3 times more increased than the case of the 1 cycle tempered. 2) As a result of the investigation for the effects of tempering cycles on hardness, the hardness at the tempering number of 2 thru 5 cyles was not decreased severely ; only about 10% decrease from those of the quenched and 1 cycle tempered case. Such hardness is equivalent to $H_{R}$/C61-62 with no bad effect on anti-abrasion of bearing steel. 3) In the case of 2 thru 5 cycle tempering as well as 1 cycle tempering, the impact value was not so improved comparing with the case of quenching, but an increase of 5 to 10% could be expected at least. 4) It was experimentally confirmed that the control of the mechanical properties improvement such as fatigue strength and fatigue life for bearing steels could be possible by the number of tempering cycles.

• Journal of Ocean Engineering and Technology
• /
• v.3 no.2
• /
• pp.638-638
• /
• 1989

It has been very important in various industry fields to improve the fatigue strength characteristics of bearings such as bearing life, fatigue limit, etc., because such poor properties could result in shortening the machinery life as well as in decreasing the accuracy. However, no successful heat treatment criterion seems to be available at present. In this study, the effect of the $170^{\circ}C\times120min$ tempering cycles repeated after $380^{\circ}C\times80min$ oil quenching for $800^{\circ}C$ spheroidizing-annealed bearing steel (STB2) as base metal on the $120^{\circ}C$ high temperature rotary bending fatigue strength characteristics were investigated, including the effects on hardness, Charpy impact value and micro-structure, in order to seek for the best heat treatment condition finally. The important results obtained are as follows : 1) The optimal cycle of tempering so that the fatigue strength .sigma. could become the highest was the 4th cycle. And it is confirmed that this $\sigma_{F}$ is about 6 times more increased than that of base metal, and about 1.3 times more increased than the case of the 1 cycle tempered. 2) As a result of the investigation for the effects of tempering cycles on hardness, the hardness at the tempering number of 2 thru 5 cyles was not decreased severely ; only about 10% decrease from those of the quenched and 1 cycle tempered case. Such hardness is equivalent to $H_{R}$/C61-62 with no bad effect on anti-abrasion of bearing steel. 3) In the case of 2 thru 5 cycle tempering as well as 1 cycle tempering, the impact value was not so improved comparing with the case of quenching, but an increase of 5 to 10% could be expected at least. 4) It was experimentally confirmed that the control of the mechanical properties improvement such as fatigue strength and fatigue life for bearing steels could be possible by the number of tempering cycles.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.149-149
• /
• 2016

Ceramic is widely known material due to its outstanding mechanical property. Besides, Zirconia(ZrO2) has a low thermal conductivity so it is advantage in a heat insulation. Because of these superior properties, ZrO2 is attracted to many fields using ultra high temperature for example vehicle engines, aerospace industry, turbine, nuclear system and so on. However brittle fracture is a disadvantage of the ZrO2. In order to overcome this problem, we can make the ceramic materials to the forms of ceramic nanoparticles, ceramic nanowhiskers and these forms can be used to an agent of composite materials. In this work, we selected Au catalyzed Vapor-Liquid-Solid mechanism to synthesize ZrO2 nanowhiskers. The ZrO2 whiskers are grown through Hot-wall Chemical Vapor Deposition(Hot wall CVD) using ZrCl4 as a powder source and Au film as a catalyst. This Hot wall CVD method is known to comparatively cost effective. The synthesis condition is a temperature of $1100^{\circ}C$, a pressure of 760torr(1atm) and carrier gas(Ar) flow of 500sccm. To observe the morphology of ZrO2 scanning electron microscopy is used and to identify the crystal structure x-ray diffraction is used.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.3 no.1
• /
• pp.19-24
• /
• 2008

To reduce time-to-market, more and more embedded system developers and system-on-chip designers rely on microprocessor-based design methodology. ARM processor has been a major player in this industry over the last 10 years. However, there are many restrictions on developing embedded software using ARM processor in the early design stage. For those who are not familiar with embedded software development environment or who cannot afford to have an expensive embedded hardware equipment, testing their software on a real ARM hardware platform is a challenging job. To overcome such a problem, we have designed VMA (Virtual ARM Machine), which offers easier testing and debugging environment to ARM based embedded system developers. Major benefits that can be achieved by utilizing a virtual ARM platform are (1) reducing development cost, (2) lowering the entrance barrier for embedded system novices, and (3) making it easier to test and debug embedded software designs. Unlike many other purely software-oriented ARM simulators which are independent of real hardware platforms, VMA is specifically targeted on SYS-Lab 5000 ARM hardware platform, (designed by Libertron, Inc.), which means that VMA imitates behaviors of embedded software as if the software is running on the target embedded hardware as closely as possible. This paper will describe how VMA is designed and how VMA can be used to reduce design time and cost.

• Journal of Korea Game Society
• /
• v.1 no.1
• /
• pp.80-87
• /
• 2001

Overseas literatures on the subject discussed so far have used the samples of tangible products and domestic studies have not limited the ranges of respondents while discussing the characteristics of the products. In the meanwhile, this paper has chosen intangible IT products as its research subject because IT area is an emerging industry in the 21st century. In addition, it has also limited the research samples to the buyers of the game software package products in order to enhance the reliability of respondency and the involvement. The results can be summarized as follows : Firstly, involvement acts as a moderator in the fair price and value of product as well as willingness to buy. Secondly, involvement acts as a moderator in the highest price and value of product as well as willingness to buy. Finally, involvement acts a moderator in the lower price and value of product.

• Journal of Life Science
• /
• v.16 no.4
• /
• pp.605-611
• /
• 2006

To investigate the possible use of probiont in fish farming industry, a bacterium with inhibitory effect against Vibrio anguillarum was isolated from gastrointestinal tract of the marine fish of yellow tail. It was identified to be Bacillus amyloliquefaciens H41 based on biochemical and physiological characterization. The optimal growth conditions of the isolated strain were 1% peptone, 1.5% yeast extract, 1% sucrose, 0.5% NaCl, 0.05% $MgSO_4{\cdot}7H_20$, pH 7.0-8.0, and 20 hr of incubation between $28-35^{\circ}C$ under aeration. The culture supernatant of the isolated strain showed inhibition activity against V. anguillarum. Inhibition activity was cleared by forming a clear zone by a paper-disk method. The maximal production of growth inhibition factor was induced by cultivation under 1% peptone, 1.5% yeast extract, 1% sucrose, 1% NaCl, 0.05% $MgSO_4{\cdot}7H_20$, pH 7.5 and at $35^{\circ}C$. The highest growth inhibition factor production was observed after 16-24 hr cultivation under aeration. The culture supernatant of the isolated strain showed inhibition activity whereas no inhibition activity was shown from the standard B. amyloliquefaciens KCTC 1724 strain. The growth inhibition affected only against V. anguillarum among other pathogenic Vibrios tested here.