• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1532-1535
• /
• 1996

Diamond-like carbon (DLC) films have been prepared by a widely-used plasma CVD with an rf (13.56MHz) plasma of $CH_4$ gas. The hydrogen incorporated in DLC films plays an important role of determining the film properties, but its exact role has not been clear. In this study, the effect of hydrogen on the film properties of DLC has been examined by adding the hydrogen gas to the $CH_4$ gas during deposition and by exposing the prepared film to the hydrogen plasma. As the content of additive hydrogen gas increases, the density and hardness of the film increase, but the growth rate decreases. The FT-IR spectroscopy results show that the number of C-H bonds decreases with increasing the hydrogen gas. Also, the variation in the position of "G" and "D" peaks due to additive hydrogen, which has been measured by the Raman spectroscopy, indicates of $sp^3$ fraction.

• Bulletin of the Korean Chemical Society
• /
• v.13 no.5
• /
• pp.520-526
• /
• 1992

The intramolecular fundamental vibrations of $CH_3CN$ trapped in solid argon matrix have been reinvestigated by means of FT-IR spectroscopy in the spectral range of 4000-500 $cm^{-1}$. By employing a quantum detector, infrared spectra could be obtained at matrix to solute ratio of 10000, allowing the clarification of the peaks due to monomeric species more clearly. Temperature controlled diffusion was initiated to identify the dimeric and polymeric species in terms of difference spectra. The assignments of monomeric and dimeric species are found, in general, to agree with the earlier work performed at higher concentration (Ar/$CH_3CN$ = 1500) using a dispersive spectrometer. Nonetheless the difficulty of minute differences between the earlier infrared and Raman spectroscopic results could be resolved. Moreover, the previously unnotified peaks due to polymeric species have been identified.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.850-852
• /
• 1998

SiC thin film have been prepared by ICP-CVD for low temperature deposition and large area deposition. The structural properties of deposited SiC films are characterized by employing SEM, FT-IR, XRD, XPS and Raman Spectroscopy. From the experimetal results, good crystallinity has been achieved in $1000^{\circ}C$ grown SiC film which have carbonization step at $1100^{\circ}C$ for substrate bias of 30V.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.207-207
• /
• 2013

기존의 그래핀 성장에 관한 연구는 열화학기상증착법(Chemical vapor deposition; CVD)을 이용한다. 그래핀 성장 제어 요소로는 촉매 기판인 전이 금속[Ru, Ir, Co, Re, Pt, Pd, Ni, Cu], 기판 전처리 과정, 수소/메탄 가스 혼합비, 작업 진공 상태, 기판온도[$800{\sim}1,000^{\circ}C$, 냉각 속도 등으로 보고 되고 있다. 그래핀 성장 원리는 Cu 촉매 기판에 메탄 가스를 $1,000^{\circ}C$ 온도에서 분해해서 탄소를 고용 시킨 후 급랭하는 도중에 석출되는 탄소에 의해 그래핀 시트가 형성되는 것으로 알려져 있다. 기존의 CVD를 열원을 이용할 경우 내부 챔버에 생기는 잠열에 의해 cooling profile의 제어가 용이하지 않다. 본 연구에서는 근적외선(Near Infrared; NIR) 열원을 이용한 CVD로 챔버 내부 잠열을 최소화하고, 냉각 공정을 Natural, Linear, Convex cooling type으로 디자인해서 cooling profile 제어가 그래핀 성장에 미치는 영향을 연구 하였다. 이렇게 성장된 그래핀을 임의의 기판(SiO2, Glass, PET film) 위에 습식방법으로 전이 시킨 후, 전기적 구조적 및 광학적 특성을 면저항(four-point probe), 전계방사 주사전자현미경(Field Emission Scanning Electron Microscope; FE-SEM), 마이크로 라만 분광법(Micro Raman spectroscopy) 및 광학현미경(optical microscope), 투과도(UV/Vis spectrometer)의 측정으로 잠열이 최소화된 NIR-CVD에서 cooling profile에 따른 그래핀 성장을 평가하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.388-388
• /
• 2011

Graphene, with its unique physical and structural properties, has recently become a proving ground for various physical phenomena, and is a promising candidate for a variety of electronic device and flexible display applications. The physical properties of graphene depend directly on the thickness. These properties lead to the possibility of its application in high-performance transparent conducting films (TCFs). Compared to indium tin oxide (ITO) electrodes, which have a typical sheet resistance of ~60 ${\Omega}/sq$ and ~85% transmittance in the visible range, the chemical vapor deposition (CVD) synthesized graphene electrodes have a higher transmittance in the visible to IR region and are more robust under bending. Nevertheless, the lowest sheet resistance of the currently available CVD graphene electrodes is higher than that of ITO. Here, we report an ingenious strategy, irradiation of MeV electron beam (e-beam) at room temperature under ambient condition,for obtaining size-homogeneous gold nanoparticle decorated on graphene. The nano-particlization promoted by MeV e-beam irradiation was investigated by transmission electron microscopy, electron energy loss spectroscopy elemental mapping, and energy dispersive X-ray spectroscopy. These results clearly revealed that gold nanoparticle with 10~15 nm in mean size were decorated along the surface of the graphene after 1.0 MeV-e-beam irradiation. The fabrication high-performance TCF with optimized doping condition showed a sheet resistance of ~150 ${\Omega}/sq$ at 94% transmittance. A chemical transformation and charge transfer for the metal gold nanoparticle were systematically explored by X-ray photoelectron spectroscopy and Raman spectroscopy. This approach advances the numerous applications of graphene films as transparent conducting electrodes.

• The Korean Journal of Malacology
• /
• v.28 no.2
• /
• pp.157-164
• /
• 2012

The patterns in X-ray diffraction (XRD) spectroscopy provide useful clue at $29.4^{\circ}$ to discriminate two types of Akoya cultured pearl which occurs difference of surface luster. Using the optical microscope, we could be confirmed that the nareous layer of each sample consist of different crystal form. In Fourier Transform Infrared (FT-IR) Spectroscopy analysis, the nareous layer of Akoya cultured pearls with poor luster shows some peaks at 712, 699, 1435, $1444cm^{-1}$ region and these peaks depend on the Calcite. But the nareous layer of pearls with excellent luster could not observed those peaks related with Calcite, we could observed Aragonite band at 699, $1085cm^{-1}$ region. Though this result, we know that the nareous layer of Akoya cultured pearls with excellent luster is mainly composed by Aragonite. Raman bands are also clearly demonstrated to occur difference of band intensity by difference of Aragonite content. In the Scanning Electron Microscope (SEM) analysis, we found that the Akoya cultured pearl luster and surface condition is associated with internal structure.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.487-487
• /
• 2011

Recently graphene has emerged as a fascinating 2D system in condensed-matter physics as well as a new material for the development of nanotechnology. The unusual electronic band structure of graphene allows it to exhibit a strong ambipolar electric field effect with high mobility. These properties lead to the possibility of its application in high-performance transparent conducting films (TCFs). Compared to indium tin oxide (ITO) electrodes, which have a typical sheet resistance of ${\sim}60{\Omega}$/sq and ~85 % transmittance in the visible range (400?900 nm), the CVD-grown graphene electrodes have a higher/flatter transmittance in the visible to IR region and are more robust under bending. Nevertheless, the lowest sheet resistance of the currently available CVD graphene electrodes is higher than that of ITO. Here, we report an ingenious strategy, irradiation of MeV electron beam (e-beam) at room temperature under ambient condition, for obtaining size-homogeneous gold nanoparticle decorated on graphene. The nano-particlization promoted by MeV e-beam irradiation was investigated by transmission electron microscopy, electron energy loss spectroscopy elemental mapping, and energy dispersive X-ray spectroscopy. These results clearly revealed that gold nanoparticle with 10 ~ 15 nm in mean size were decorated along the surface of the graphene after 1.5 MeV-e-beam irradiation. A chemical transformation and charge transfer for the metal gold nanoparticle were systematically explored by X-ray photoelectron spectroscopy and Raman spectroscopy. This approach advances the numerous applications of graphene films as transparent conducting electrodes.

• Journal of Korean Ophthalmic Optics Society
• /
• v.13 no.1
• /
• pp.37-42
• /
• 2008

Purpose: This study is to prepare tintable hard coatings for plastic lenses and to evaluate spectroscopic and surface characteristic for these coatings. Methods: These coatings had been prepared by the sol-gel method using TEOS, MTMS and GPTS. Scanning electron microscopy (SEM), Raman spectroscopy, infrared (IR) spectroscopy and UV/VIS spectroscopy have been used to investigate the optical and structural characteristics of the coatings. Results: Tint ability of this coating was about 2 times higher than general hard coatings. The lenses applied by tintable hard coatings showed excellent adhesion, abrasion resistance, hot water resistance, and chemical resistance. Pencil hardness was 5H and the surface of coatings was smooth and free of cracks. Conclusions: This hard coating system for plastic lenses offered a hard and stable surface that could be tinted.

• Resources Recycling
• /
• v.26 no.1
• /
• pp.69-77
• /
• 2017

Used small household appliances(small e-waste) consists of a variety of complex materials and components. The small e-waste is mainly composed of plastics and an important potential source of waste plastic. The black plastics, particularly are very difficult to separate by resin type and therefore these are mainly recycled in the form of a mixtures. In the present study, the sorting technologies such as gravity and electro static separation, near-infrared ray(NIR) and IR/Raman optical sorting separation on mixture of black plastics were analyzed and their limitations on sorting process were also investigated. The Laser Induced Breakdown Spectroscopy(LIBS) spectrum of each black plastics was used for identification of black plastics by resin type, and after analyzing the normalization operation, Principal Component Analysis(PCA) was carried out. The spectrum data was optimized through PCA process. In order to improve the identification accuracy and sorting efficiency of black plastics, it is necessary to design a classifier with high efficiency and to improve the performance and reliability of the classifier by applying the field of intelligent algorithms.

• Journal of Conservation Science
• /
• v.37 no.5
• /
• pp.606-616
• /
• 2021

From the collection of the National Kimhae Museum, qualitative analyses using microscopic observation, SEM-EDS, Raman spectroscopy, FT-IR-ATR spectroscopy, and GC-MS were conducted on three burnished red potteries-Jeoksaekmaoyeonwa burnished red pottery (Neolithic age red pottery), Dandomaoyeonwan burnished red pottery(Bronze age red pottery) and Jeoksaekmaoyeongajimun burnished red pottery(Bronze age red pottery)-to investigate the components of the red pigments and the binder. After the layers of the primer were separated from the red surface, crystals of red pigment particles and minerals were found on the red surface. Through SEM-EDS, Raman estimates that the red pigment is Among soil pigments with iron oxide(Fe₂O₃) as the main color development source, Red Ocher(Fe₂O₃). A band characteristic of the Urushiol polymer was detected in the FTIR-ATRspectra(4000~600cm^-1), GC-MS analysis confirmed the presence of the benzenemethanol-2-prophenyl, 4-heptylphenol, 1-tetracecanol, heptafluorobutyric texidecane, all of which are the ingredients of the directional structure of the lacquer present in the red layer. Therefore, it seemed that the three burnished red pottery: Jeoksaekmaoyeonwan pottery(Neolithic age burnished red pottery), Dandomaoyeonwan pottery(bronze age burnished red pottery) and the Jeoksaekmaoyeongajimun pottery(bronze age burnished red pottery) made by mixing minerals and Red Ocher(Fe₂O₃), with lacquer.