• 멤브레인
• /
• 제17권1호
• /
• pp.61-66
• /
• 2007

고분자 분리막에 비하여 열적, 기계적, 화학적 안정성이 우수한 친수성 NaY 제올라이트 분리막을 이용한 투과 증발 막분리 공정을 적용하여 이소프로필 알코올(iso-propyl alcohol, IPA)/물 혼합물에서 선택적으로 물을 분리하고자 하였다. 공급되는 IPA의 몰분율 변화 및 투과 증발 실험 온도의 변화가 투과플럭스와 물 선택도에 미치는 영향을 고찰하였다. IPA의 몰분율이 증가함에 따라 물 투과플럭스와 선택도는 감소함을 관찰할 수 있었다. 실험 온도의 증가에 따라 물 투과플럭스는 증가하였으나 선택도는 감소하였다 친수성 NaY 제올라이트 투과증발 실험 결과 $1.9{\times}10^2{\sim}3.5{\times}10^3\;g/m^2{\cdot}hr$의 물 투과플럭스와 $7.0{\times}10^2{\sim}2.0{\times}10^4$의 선택도를 나타내었다.

• 멤브레인
• /
• 제16권1호
• /
• pp.25-30
• /
• 2006

[ ${\alpha}$ ]-알루미나 튜브 지지체의 내부에 1Si : 1Na : 4Na : $6H_{2}O$의 비율로 제조한 합성 용액을 사용하여 수열합성법으로 NaA 제올라이트 분리막을 제조하였다. 합성된 제올라이트 분리막을 이용하여 iso-propyl alcohol (IPA)/물 혼합물의 조성비와 조업 온도 변화에 따른 선택도와 투과도의 변화를 알아보기 위한 투과증발 실험을 수행하였다. 총투과도는 공급 측 IPA의 농도가 증가함에 따라 감소하였고, 온도가 상승함에 따라 증가하는 경향을 보였다. 총투과도는 $60^{\circ}C$에서 공급물의 IPA농도가 0.6 몰분율일 때 $4.0{\times}10^3g/m^2\;hr$로 가장 높은 값을 보였다. 선택도는 IPA의 몰비가 0.8까지 증가하는 경향을 보였고 0.9 이상에서 감소하는 경향을 나타내었다 선택도는 $60^{\circ}C$, 0.8 몰분율에서 $1.8{\times}10^7$의 값으로 최고치를 나타내었다. NaA 제올라이트 분리막을 이용한 투과증발은 기존의 증류공정과 비교 시 훨씬 우수한 선택적 물 분리 성능을 나타내었다.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권5호
• /
• pp.481-486
• /
• 1997

This paper describes the anisotropic etching characteristics of Si in acqueous TMAH/IPA solutions. The etch rates of (100) oriented Si crystal planes decrease with increasing TMAH concentration and IPA concentration. Etchant concentration and etch temperature have a large effect on hillock density. Hillock density strongly increase with lower TMAH concentration and higher etch temperature. The etched (100) planes are covered by pyramidal-shaped hillocks below TMAH 15 wt.%, but very smooth surface is obtained TMAH 25 wt.%. The addition of IPA to TMAH solution leads to smoother surfaces of sidewalls etched planes. Undercutting ratio of pure TMAH solution is much higher than KOH. But, addition of IPA to TMAh the underrcutting ratio reduces by a factor of 3∼4. Therefore, acqueous TMAH/IPA solution is able to use as anisotropic etchant of Si because of full compability with IC fabrication process.

• Journal of Advanced Marine Engineering and Technology
• /
• 제30권1호
• /
• pp.102-108
• /
• 2006

On the refutation demanded for a control of various toxic substances. PCBs(poly chlorinated biphenyl) has a fatal poisonous matter in the ecosystem and the environmental pollution as it Is a kind of stable chemical substance. Especially, the gross Product of PCBs is estimated at about one million tonnage all over the world. However it is kept on storing in untreated state, then has a deterioration by the Prolonged storage and a risk of overflowing. Therefore, this research examined the fundamental characteristics of combustion and emission for the target of using the IPA (iso-propyl alcohol) solution as a part of PCBs control. IPA was filled to three kinds of Vessel, i.e. Vessel I, II, and III, and then was investigated as follows combustion shape, flame temperature. mass burning velocity, and PM(Particulate matter). A radial thermometer and a C-A thermocouple measured the flame temperature, and the optical extinction method by using He-Ne laser and the filter weight method used in the PM measurement. As a result, with an increasing of L/S ratio, the flame length become shorter and the burning velocity is more rapid, but the particulate matters is higher. It is supposed that the air flow rate is high on Vessel. and then the combustion is Promoted in the surface area of the upstream zone. The future works plan to investigate the characteristics with an using of the mixing of IPA and PCBs

• Transactions on Electrical and Electronic Materials
• /
• 제13권2호
• /
• pp.89-92
• /
• 2012

The effect of organic impurities on the electrical properties of a neat epoxy resin was studied. 0.05, 0.5 and 1.0 phr of iso-propyl alcohol (IPA) and methylene chloride (MC) mixture (50/50 wt%) were used as impurities. The current density, volume resistance and impedance characteristics of the epoxy/IPA/MC systems were measured with a high voltage source meter and broadband dielectric spectroscopy. Glass transition temperature (Tg) was measured by a differential scanning calorimetry (DSC) and it was found that Tg decreased slightly with increasing IPA/MC content. It was also found that Tg values of the epoxy systems with various IPA/MC contents were closely related to the current density, volume resistance and impedance characteristics.

• 한국염색가공학회지
• /
• 제17권3호
• /
• pp.34-42
• /
• 2005

In this work, a practical separation performance was investigated on aqueous alcohol solutions, especially for iso-propyl alcohol (IPA), which is usually used during the semi- conductor rinsing process. The removal of various substances from waste aqueous IPA solutions was carried out by microfiltration with $0.1\~1{\mu}$m pore size of mean diameter as a pre-filter. Permeability and molecular weight cut-off of the functional polysulfone(PSf) ultrafiltration membrane to purify waste aqueous IPA solutions were measured through the ultrafiltration test. The solute rejection of PSf membrane had $92\%$ in 1,000ppm aqueous PEG solution with PEG molecular weight 10,000, the molecular weight cut-off had 10,000. The IPA concentration on the $CMPA-K^+$ membrane performance using pervaporation module system could be increased from $95.04 wt\%$ to more than $98.50wt\%$ in about 9hr at operation temperature of $70^{\circ}C$ using the pervaporation module system.

• 멤브레인
• /
• 제23권3호
• /
• pp.245-250
• /
• 2013

PDMS 단일 막을 이용한 투과증발공정을 통해 이소프로필알코올(Isopropyl alcohol, IPA)-물계에 대한 분리특성을 알아보았다. RTV-655 주재와 가교제의 비율을 9:1과 10:1로 달리하고 반응온도를 40, 60, $80^{\circ}C$로 변화하여 경화시켰다. 이렇게 제조된 막을 이용하여 특성평가를 위해 물/IPA 혼합액에 대한 투과증발 실험을 수행하였다. 공급액의 조성은 85 wt% IPA 수용액을 사용하였으며, 온도는 25, 35, 45, $55^{\circ}C$로 변화시켰다. 공급액의 변화와 반응온도의 조건변화에 따른 투과도 및 IPA 농축농도를 측정하였는데, 투과도는 9:1 비율, 공급액 온도 $55^{\circ}C$일 때 $148g/m^2{\cdot}hr$, 선택도는 10:1 비율, 공급액 온도 $55^{\circ}C$일 때 17%로 가장 높은 값을 얻을 수 있었다.

• 한국염색가공학회지
• /
• 제17권4호
• /
• pp.21-26
• /
• 2005

A combination separation system is composed of three parts, simple microfiltration unit for the pretreatment of real waste IPA, pervaporation unit with plate and frame type module(the effective membrane area 9,040$cm^2$), and simple ultrafiltration unit as a refiner. Utrafiltration module with hollow fiber membrane(MWCO 10,000) used to purify waste aqueous IPA solution. In addition, the flux of $CMPA-K^+$ composite membrane for waste aqueous IPA solution was very steady-state with long experiment time(30 days). And the standard deviation($\sigma$) was 0.152 and then the coefficient of variation($CV\%$)was 10.82 The IPA concentration on the membrane performance using pervaporation module system could be increased from $89.85wt(\%)$ to more than $99.90wt\%$ in about 8hr at operation temperature of $70^{\circ}C$ using the pervaporation module system. Therefore, a combination separation process system of simple filtration and pervaporation was very effective for the purpose of the IPA purification and reuse front industrial electronic components cleaning process.

• 한국화재소방학회논문지
• /
• 제14권2호
• /
• pp.33-38
• /
• 2000

전자산업의 공정에서 PCB기판납땜은 괼수적이며 이에 사용하는 Flux내 용제인 IPA(Iso--propyl alcohol)와 메탄올은 인화성과 폭발성이 강한 물질로 화재위험성이 대단히 높다. 또한 메탄올은 유독성물질로 지정되어 있으며, 환경법상 VOC(Volatile Organic Compound : 휘발성유기화합물)규제물질로 지정되어 있어 대체물질 개발이 절실히 요구된다. 이에 기존 Flux특성을 가지고 있으면서 화재위험성은 없고, 휘발성유기화합물 규제물질에는 해당되지 않는 디클로로프로판(Dichloropropane, DCP)를 주성분으로 하여 Flux 특성에 맞는 안정제 및 첨가제를 적정 조성비로 조합하여 용제를 개발하였다. 그 결과 200ppm의 작업환경허용농도를 470 ppm으로 완화시킬 수 있었으며 납땜불량율은 0.083%에서 0%로, 퍼짐성은 85%에서 87%로, 전연저항은 1.0$\times$$10^{12}$$\Omega$에서 6.9$\times$$10^{12}$/$\Omega$으로 기존 Flux보다 우수하였다. 그러므로 Flux의 안정성은 물론 환경안전측면과 품질, 생산성도 향상이 가능함을 확인하였고, 품질 특성시험 및 제품 신뢰성 시험 결과 만족할 만한 곁과를 얻었다.

• Journal of Electrochemical Science and Technology
• /
• 제12권2호
• /
• pp.204-211
• /
• 2021

We report, synthesis of high surface area composite carbon aerogel using additive based polymerization technique by incorporating graphitic porous carbon as additive. This additive was separately prepared using sol-gel polymerization of resorcinol-furfuraldehyde in iso-propyl alcohol medium at much above the routine gelation temperature to yield porous carbon (CA-IPA) having graphitic layered morphology. CA-IPA exhibited a unique combination of meso-pore dominated surface area (~ 700 m²/g) and good conductivity of ~ 300 S/m. The composite carbon aerogel (CCA) was synthesized by traditional aqueous medium based resorcinol-formaldehyde gelation with CA-IPA as additive. The presence of CA-IPA favored enhanced meso-porosity as well as contributed to improvement in bulk conductivity. Based on the surface area characteristics, CCA-8 composition having 8% additive was found to be optimum. It showed specific surface area of ~ 2056 m²/g, mesopore area of 827 m²/g and electrical conductivity of 180 S/m. The electrode formed with CCA-8 showed improved electrochemical behavior, with specific capacitance of 148 F/g & ESR < 1 Ω, making it a better choice as super capacitor for energy storage applications.