• Membrane Journal
• /
• v.17 no.1
• /
• pp.61-66
• /
• 2007

A zeolite membrane shows better thermal, mechanical and chemical stabilities than a polymer membrane. Water was separated from iso-propyl alcohol (IPA)/water mixtures by pervaporation using the NaY zeolite membrane synthesized in the laboratory. The effects of a mole fraction of IPA in the feed solution and an operating temperature were studied on the permeation flux behavior and the separation factor of water with respect to IPA. As a mole fraction of IPA increased, the water flux as well as the separation factor decreased. As the experimental temperature increased, the water permeation flux increased while the separation factor decreased. For IPA/water binary mixtures, the water flukes through the NaY zeolite membrane were observed to be $1.9{\times}10^2{\sim}3.5{\times}10^3\;g/m^2{\cdot}hr$ and the separation factors were found to be $7.0{\times}10^2{\sim}2.0{\times}10^4$.

• Membrane Journal
• /
• v.16 no.1
• /
• pp.25-30
• /
• 2006

The NaA zeolite membrane was synthesized on the surface of a porous ${\alpha}$-alumina support from the reaction solution composed of 1Si : 1Na : 4Na $6H_{2}O$. The pervaporation performance of the synthesized NaA zeolite membrane was investigated for the iso-propyl alcohol (IPA) aqueous solution according to the different feed concentration and the different operating temperature. The total flux decreases by increasing the feed IPA concentration and increases by increasing the temperature. The total flux was about $4.0{\times}10^3g/m^2\;hr\;at\;60^{\circ}C$ and 0.6 mole fraction of IPA and the separation factor was $1.8{\times}10^7\;at\;60^{\circ}C$ and 0.8 mole fraction of IPA. The separation performance of water through the NaA membrane was found to be superior to that obtainable with a distillation process just by comparison of the vapor-liquid equilibrium data.

• Electrical & Electronic Materials
• /
• v.10 no.5
• /
• pp.481-486
• /
• 1997

This paper describes the anisotropic etching characteristics of Si in acqueous TMAH/IPA solutions. The etch rates of (100) oriented Si crystal planes decrease with increasing TMAH concentration and IPA concentration. Etchant concentration and etch temperature have a large effect on hillock density. Hillock density strongly increase with lower TMAH concentration and higher etch temperature. The etched (100) planes are covered by pyramidal-shaped hillocks below TMAH 15 wt.%, but very smooth surface is obtained TMAH 25 wt.%. The addition of IPA to TMAH solution leads to smoother surfaces of sidewalls etched planes. Undercutting ratio of pure TMAH solution is much higher than KOH. But, addition of IPA to TMAh the underrcutting ratio reduces by a factor of 3∼4. Therefore, acqueous TMAH/IPA solution is able to use as anisotropic etchant of Si because of full compability with IC fabrication process.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.1
• /
• pp.102-108
• /
• 2006

On the refutation demanded for a control of various toxic substances. PCBs(poly chlorinated biphenyl) has a fatal poisonous matter in the ecosystem and the environmental pollution as it Is a kind of stable chemical substance. Especially, the gross Product of PCBs is estimated at about one million tonnage all over the world. However it is kept on storing in untreated state, then has a deterioration by the Prolonged storage and a risk of overflowing. Therefore, this research examined the fundamental characteristics of combustion and emission for the target of using the IPA (iso-propyl alcohol) solution as a part of PCBs control. IPA was filled to three kinds of Vessel, i.e. Vessel I, II, and III, and then was investigated as follows combustion shape, flame temperature. mass burning velocity, and PM(Particulate matter). A radial thermometer and a C-A thermocouple measured the flame temperature, and the optical extinction method by using He-Ne laser and the filter weight method used in the PM measurement. As a result, with an increasing of L/S ratio, the flame length become shorter and the burning velocity is more rapid, but the particulate matters is higher. It is supposed that the air flow rate is high on Vessel. and then the combustion is Promoted in the surface area of the upstream zone. The future works plan to investigate the characteristics with an using of the mixing of IPA and PCBs

• Transactions on Electrical and Electronic Materials
• /
• v.13 no.2
• /
• pp.89-92
• /
• 2012

The effect of organic impurities on the electrical properties of a neat epoxy resin was studied. 0.05, 0.5 and 1.0 phr of iso-propyl alcohol (IPA) and methylene chloride (MC) mixture (50/50 wt%) were used as impurities. The current density, volume resistance and impedance characteristics of the epoxy/IPA/MC systems were measured with a high voltage source meter and broadband dielectric spectroscopy. Glass transition temperature (Tg) was measured by a differential scanning calorimetry (DSC) and it was found that Tg decreased slightly with increasing IPA/MC content. It was also found that Tg values of the epoxy systems with various IPA/MC contents were closely related to the current density, volume resistance and impedance characteristics.

• Textile Coloration and Finishing
• /
• v.17 no.3 s.82
• /
• pp.34-42
• /
• 2005

In this work, a practical separation performance was investigated on aqueous alcohol solutions, especially for iso-propyl alcohol (IPA), which is usually used during the semi- conductor rinsing process. The removal of various substances from waste aqueous IPA solutions was carried out by microfiltration with $0.1\~1{\mu}$m pore size of mean diameter as a pre-filter. Permeability and molecular weight cut-off of the functional polysulfone(PSf) ultrafiltration membrane to purify waste aqueous IPA solutions were measured through the ultrafiltration test. The solute rejection of PSf membrane had $92\%$ in 1,000ppm aqueous PEG solution with PEG molecular weight 10,000, the molecular weight cut-off had 10,000. The IPA concentration on the $CMPA-K^+$ membrane performance using pervaporation module system could be increased from $95.04 wt\%$ to more than $98.50wt\%$ in about 9hr at operation temperature of $70^{\circ}C$ using the pervaporation module system.

• Membrane Journal
• /
• v.23 no.3
• /
• pp.245-250
• /
• 2013

In this study, the pervaporation separation characteristics were investigated for the iso-propyl alcohol (IPA)-water system using PDMS dense membranes. The ratio, 9:1 and 10:1, of the basic material based on RTV-655 and crosslinking agent were used to prepare dense membranes at the reaction temperatures, 40, 60, and $80^{\circ}C$. And these resulting membranes were characterized by pervaporation technique in terms of permeabilities and separation factors for the feed composition of IPA 85 wt% at the operating temperatures, 25, 35, 45, and $55^{\circ}C$. Typical results of permeabilities $148g/m^2{\cdot}hr$ at $55^{\circ}C$ for 9:1 membrane and the selectivity 17 at $55^{\circ}C$ for 10:1 membrane were obtained, respectively.

• Textile Coloration and Finishing
• /
• v.17 no.4 s.83
• /
• pp.21-26
• /
• 2005

A combination separation system is composed of three parts, simple microfiltration unit for the pretreatment of real waste IPA, pervaporation unit with plate and frame type module(the effective membrane area 9,040$cm^2$), and simple ultrafiltration unit as a refiner. Utrafiltration module with hollow fiber membrane(MWCO 10,000) used to purify waste aqueous IPA solution. In addition, the flux of $CMPA-K^+$ composite membrane for waste aqueous IPA solution was very steady-state with long experiment time(30 days). And the standard deviation($\sigma$) was 0.152 and then the coefficient of variation($CV\%$)was 10.82 The IPA concentration on the membrane performance using pervaporation module system could be increased from $89.85wt(\%)$ to more than $99.90wt\%$ in about 8hr at operation temperature of $70^{\circ}C$ using the pervaporation module system. Therefore, a combination separation process system of simple filtration and pervaporation was very effective for the purpose of the IPA purification and reuse front industrial electronic components cleaning process.

• Fire Science and Engineering
• /
• v.14 no.2
• /
• pp.33-38
• /
• 2000

Flux, essentially used in soldering process of PCB (Printed Circuit Board) in electronics industry, contains IPA (Isopropyl alcohol) and methanol, which are highly inflammable and explosive. Hazard Chemical Controlling Law classified methanol as toxic material and Environmental Law classified methanol as VOC (Volatile Organic Compound). So there have been pressing needs of developing substitutes for the existing Flux. New solvent which is non-flammable and main component is DCP having same specific character of the existing Flux. It's been combirated with proper composition ratio adding stabilizer. As a result, it relieved working Environment Allowance thickness 200 ppm to 470 ppm, chance of not been soldered 0.083% to 0%, spread 85% to 87%, power saving resistance 1.0$\times$$10^{12}$$\Omega$ to 6.9$\times$$10^{12}$$\Omega$, which means a lot better than the existing Flux. Therefore, Flux confirmed the chance of improving productivity, safety, environment safety and quality. Also, Flux got a satisfied result after product quality test and product reliability test.

• Journal of Electrochemical Science and Technology
• /
• v.12 no.2
• /
• pp.204-211
• /
• 2021

We report, synthesis of high surface area composite carbon aerogel using additive based polymerization technique by incorporating graphitic porous carbon as additive. This additive was separately prepared using sol-gel polymerization of resorcinol-furfuraldehyde in iso-propyl alcohol medium at much above the routine gelation temperature to yield porous carbon (CA-IPA) having graphitic layered morphology. CA-IPA exhibited a unique combination of meso-pore dominated surface area (~ 700 m²/g) and good conductivity of ~ 300 S/m. The composite carbon aerogel (CCA) was synthesized by traditional aqueous medium based resorcinol-formaldehyde gelation with CA-IPA as additive. The presence of CA-IPA favored enhanced meso-porosity as well as contributed to improvement in bulk conductivity. Based on the surface area characteristics, CCA-8 composition having 8% additive was found to be optimum. It showed specific surface area of ~ 2056 m²/g, mesopore area of 827 m²/g and electrical conductivity of 180 S/m. The electrode formed with CCA-8 showed improved electrochemical behavior, with specific capacitance of 148 F/g & ESR < 1 Ω, making it a better choice as super capacitor for energy storage applications.