• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2006.11a
• /
• pp.327-328
• /
• 2006

중 저준위방사성폐기물(이하, '방폐물'이라 함)을 처분시설로 안전하고 효율적으로 운반하기 위하여 원자력법[1][2] 및 IAEA 안전운반규정(3) 등 국내외 관련규정의 기술기준을 만족시키는 안전성이 확보된 운반용기를 사용하여야 한다. 방폐물이 저준위비방사능(LSA: Low Specific Activity)물질 또는 표면오염물체(SCO; Surface Contaminated Object)로 분류되고 전용상태로 운반되는 경우는 거의 IP-2형 운반용기를 이용하여 운반하는 것이 가능하다. 방폐물 처분시설이 경주의 임해지역에 건설되어 운영된 것이므로 일부를 제외한 대부분의 방폐물은 IP-2형 운반용기에 적재하여 전용선박을 이용하여 해상으로 운반하게 된다. 전용선박은 크레인을 이용하여 화물을 선적하고 하역하는 Lo/Lo(Lift-on/Lift-off) 방식으로 IMO 규정 및 국내 선박법에 따라 국내에서 설계, 건조될 예정이며, 선박의 규모는 총 톤수 약 2,000톤이며, 약 1,600드럼의 방폐물을 적재할 수 있다. 여기서는 방폐물의 해상운반을 위한 IP-2형 운반용기에 대한 요건 및 관련규정에 따른 기술기준을 입증하기 위한 건전성 평가방안에 대하여 기술하였다.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.10 no.1
• /
• pp.37-43
• /
• 2012

Radioactive waste transport package was developed to transport eight drums of low and intermediate level waste(LILW) in accordance with the IAEA and domestic related regulations. The package is classified with industrial package IP-2. IP-2 package is required to undergo a free drop test and a stacking test. After free drop and stacking tests, it should prevent the loss or dispersal of radioactive contents, and loss of shielding integrity which would result in more than 20 % increase in the radiation level at any external surface of the package. The objective of this study is to establish the safety test method and procedure for stacking test and to prove the structural integrities of the IP-2 package. Stacking test and analysis were performed with a compressive load equal to five times the weight of the package for a period of 24 hours using a full scale model. Strains and displacements were measured at the corner fitting of the package during the stacking test. The measured strains and displacements were compared with the analysis results, and there were good agreements. It is very difficult to measure the deflection at the container base, so the maximum deflection of the container base was calculated by the analysis method. The maximum displacement at the corner fitting and deflection at the container base were less than their allowable values. Dimensions of the test model, thickness of shielding material and bolt torque were measured before and after the stacking test. Throughout the stacking test, it was found that there were no loss or dispersal of radioactive contents and no loss of shielding integrity. Thus, the package was shown to comply with the requirements to maintain structural integrity under the stacking condition.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.5 no.3
• /
• pp.199-212
• /
• 2007

If a type IP-2 transport package were to be subjected to a free drop test and a penetration test under the normal conditions of transport, it should prevent a loss or dispersal of the radioactive contents and a more than 20% increase in the maximum radiation level at any external surface of the package. In this paper, we suggested the analytic method to evaluate the structural safety of a type IP-2 transport package using a thick steel plate for a structure part and a bolt for tying a bolt. Using an analysis a loss or dispersal of the radioactive contents and a loss of shielding integrity were confirmed for two kinds of type IP-2 transport packages to transport radioactive waste drums from a waste facility to a temporary storage site in a nuclear power plant. Under the free drop condition the maximum average stress at the bolts and the maximum opening displacement of a lid were compared with the tensile stress of a bolt and the steps in a lid, which were made to avoid a streaming radiation in the shielding path, to evaluate a loss or dispersal of radioactive waste contents. Also a loss of shielding integrity was evaluated using the maximum decrease in a shielding thickness. To verify the impact dynamic analysis for free drop test condition and evaluate experimentally the safety of two kinds of type IP-2 transport packages, free drop tests were conducted with various drop directions. For the tests we examined the failure of bolts and the deformation of flange to evaluate a loss or dispersal of radioactive material and measured the shielding thickness using a ultrasonic thickness gauge to assess a loss of shielding integrity. The strains and accelerations acquired from tests were compared with those by analyses to verify the impact dynamic analysis. The analytic results were larger than the those of test so that the analysis showed the conservative results. Finally, we evaluated the safety of the type IP-2 transport package under the stacking test condition using a finite element analysis. Under the stacking test condition, the maximum Tresca stress of the shielding material was 1/3 of the yielding stress. Two kinds of a type IP-2 transport package were safe for the free drop test condition and the stacking test condition.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2005.11a
• /
• pp.339-347
• /
• 2005

A type IP-2 transport package should prevent a loss or dispersal of the radioactive contents and a more than $20\%$ increase in the maximum radiation level at any external surface of the package when it were subjected to the drop test under the normal conditions of transport. If a shielding thickness of IP-2 transport package is thick, a bolted lid type may prevent a loss or dispersal of the radioactive contents than the door type of ISO containers which are generally used as a type IP-2 transport package. In this paper, to evaluate the effect of drop directions on the bolt tension and the coherence of a bolt, the drop tests of preliminary small model are tested and evaluated for seven directions before the drop test of a type IP-2 transport package with a bolted lid type under the normal conditions of transport. Seven drop directions which are a bottom-vertical drop, a lid-vortical drop. a horizontal drop and four corner drops have been carried out. Using a force sensor, the bolt tension during the drop impact is measured. The coherence of bolt is evaluated by the difference between the fastening torque of bolt before a drop test and the unfastening torque of bolt after a drop impact.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2007.11a
• /
• pp.336-337
• /
• 2007

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.14 no.2
• /
• pp.157-168
• /
• 2016

Radioactive waste container designs should comply with the requirements for safety (i.e., transportation, storage, disposal) and other criteria such as economics and technology. These criteria are also applicable to the future management of the large amount of LLW and VLLW to arise from decontamination and decommissioning (D&D) of nuclear power plants, which have different features compared to that of wastes from operation and maintenance (O&M). This paper proposes to develop a set of standard containers of multi-purpose usage for transportation, storage and disposal. The concepts of the containers were optimized for management of D&D wastes in consideration of national system for radioactive waste management, in particular the Gyeongju Repository and associated infrastructures. A set of prototype containers were designed and built : a soft bag for VLLW, two metallic containers for VLLW/LLW (a standard IP2 container for sea transport and ISO container for road transport). Safety analyses by simulation and tests of these designs show they are in compliance with the regulatory requirements. A further development of a container with concrete is foreseen for 2016.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.6
• /
• pp.35-40
• /
• 2015

An IP-2 type container is used for the transport of low-level radioactive materials. An IP-2 type metal container was modeled and analyzed for the dropping conditions in normal transport conditions required by NSSC Notice 2014-50, "Regulations on the packaging and transport of radioactive materials." Structural analyses were performed by finite element method, and the acceptability was reviewed by comparing the results with technical standards and maximum allowable stresses of each material. Structural members of the container were modeled as 3D solid elements, and the possible dropping directions were considered in these analyses. Results show that maximum stresses, maximum deformed gaps in the cover, and maximum estimated thickness reduction in structural members were well below the allowable limits; thus, the structural integrity of the container was confirmed.