• 한국음향학회지
• /
• 제11권6호
• /
• pp.32-40
• /
• 1992

This study shows how the finite element method for the structural problems could be applied in the electromechanical impedance analysis of an in-air piezoelectric cylinder transducer and then compares the numerical results by the FEM with the measured results using the impedance analyzer. The results also show that the comparison between both results could be applied to examine the mechanical properties of the added unknown material to transducer such as an acoustic window.

• 대한전자공학회논문지
• /
• 제7권4호
• /
• pp.1-5
• /
• 1970

본 논문에서는 전차선형초광대역 FM 변별기의 결합저항식(변별기에 사용된 전송선의 특성임피단스)와의 오차가 ±10%이내일 때 전송선형 FM 변별기의 입력임피단스와 출력파형의 디스토숀에 미치는 영향을 고찰했다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1985년도 하계학술회의논문집
• /
• pp.224-227
• /
• 1985

During operation of an RF glow discharge system, it can be observed that the reflected power tends to increase in small value, due to changes in the impedance of the system. This problem can be relieved by adding an automatic impedance matching circuit to the system. This paper presents a detailed method of automatically matching the input impedance of a 50 ohm transmission line to an RF glow discharge system at 13.56 MHZ.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2005년도 종합학술발표회 논문집 Vol.15 No.1
• /
• pp.353-356
• /
• 2005

There have been many researches on the antenna performance degradation with the presence of the human body around the antenna structure to accomodate personal communication service [1][2]. To better understand the human body effects on the antenna resonance, radiation pattern, and input impedance, simulation was carried out with changing of the distance between antenna and lossy material. Effects on the antenna performance by the surrounding materials are also important in the case of the RFID system. It is desirable that the tag antennas for RFID system must reveal isotropic radiation pattern as well as attain the good impedance matching. In this paper, we investigated the antenna resonance and input impedance characteristic when there exist a lossy material sphere near various types of antenna at 900 MHz. In short antenna resonance was mostly affected by lossy material in the case of a rectangular loop antenna, and impedance variation was smallest in the case of a halfwave dipole.

• 한국정보통신학회논문지
• /
• 제26권11호
• /
• pp.1686-1696
• /
• 2022

본 논문에서 소개하는 페이저도에 의한 임피던스 정합회로 설계는 회로이론의 임피던스 삼각도에 기초한다. 정합회로 설계에 주어진 값들을 이용하여 페이저 도형의 작도를 통하여 설계하는 기법이다. 설계 패턴은 L형, 역L형, T형, 𝜋형을 기본으로, 미지의 리액턴스 소자를 페이저 도형을 통하여 결정한다. 본 논문에서는 입력과 출력포트가 순저항인 경우와 리액턴스를 갖는 경우의 몇 가지 사례에 대하여 설계하고 이를 직병렬 등가변환에 의하여 설계값을 검증하여 정합이 이루어짐을 확인하였다. 본 설계 기법은 입출력 위상이나 크기를 바로 파악할 수 있어 설계의 변경과 적용이 신속하여 주로 낮은 주파수 대역에서 적용이 기대된다.

• Journal of information and communication convergence engineering
• /
• 제10권2호
• /
• pp.103-107
• /
• 2012

An end-launched adapter combining a coaxial loop within a rectangular waveguide has been analyzed and designed. The accurate electromagnetic modeling of input impedance for the adapter design has been developed using a modal analysis method. Also, design parameters to improve the end-launched adapter have been investigated. Numerical and experimental results of the proposed model have been compared with the results of previous works, and verified by an electromagnetic simulator of High Frequency Structure Simulator (HFSS). The input voltage standing wave ratios (VSWRs) are smaller than 2 over the wide frequency band from 7.5 GHz to 10.5 GHz.

• 전자공학회논문지A
• /
• 제31A권2호
• /
• pp.18-25
• /
• 1994

In this papaer, the input impedance of the rectangular microstrip patch antennas with the multilayered structure is analysed by using the moment method technique in the spectral domain. The analysis is carried out for two different feeding structures : directfeeding structure and electromagnetic-feeding structure. In order to obtain the accurate input impedance, the current distribution on the microstrip feed line is modeled by the quasi-TEM travelling wave and the PWS(piecewise sinusoidal) mode. The input impedances of the designed microstrip antennas are measured and compared with the calculation. which shows a good agreement.

• Journal of Electrical Engineering and Technology
• /
• 제2권1호
• /
• pp.29-34
• /
• 2007

The input and output impedances in a low voltage distribution system is one of the most important matters for power line communication because from the viewpoint of communication, the attenuation characteristic of the high frequency signals is greatly caused by impedance mismatch during sending and receiving. The frequency range is from 1MHz to 30MHz. Therefore, this paper investigates the input and output impedances in order to understand the characteristic of high frequency signals in the low voltage distribution system between a pole transformer and an end user. For power line communication, the model of Korea's low voltage distribution system is proposed in a residential area and then the low voltage distribution system is set up in a laboratory. In the low voltage distribution system, S parameters are measured by using a network analyzer. Finally, input and output impedances are calculated using S parameters.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제51권10호
• /
• pp.581-586
• /
• 2002

To improve the current waveform of diode rectifiers, we propose a new operating principle for the voltage-doubler diode rectifiers. In the conventional voltage-doubler rectifier circuit, relatively large capacitors are used to boost the output voltage, while the proposed circuit uses smaller ones and a small reactor not to boost the output voltage but improve the input current waveform. A circuit design method is shown by experimentation and confirmed simulation. The experimental results of the proposed diode rectifier satisfies the harmonic guide lines. A high input power factor of 97(%) and an efficiency of 98[%] are also obtained. The new rectifier with no controlled switches meet the harmonic guide lines, resulting in a simple, reliable and low-cost at-to dc converters in comparison with the boost-type current-improving circuits. This paper proposes a nonlinear impedance circuit composed by diodes and inductors or capacitors. This circuit needs no control circuits and switches, and the impedance value is changed by the polarity of current or voltage. And this paper presents one of these applications to improve the input current of capacitor input diode rectifiers. The rectifier using the nonlinear impedance circuit is constructed with four diodes and four capacitors in addition to the conventional rectifiers, that is, it has eight diodes and five capacitors, including a DC link capacitor. It makes harmonic components of the input current reduction and the power factor improvement. Half pulse-width modulated (HPWM) inverter was explained compared with conventional pulse width modulated(PWM) inverter. Proposed HPWM inverter eliminated dead-time by lowering switching loss and holding over-shooting.

• Journal of Power Electronics
• /
• 제15권3호
• /
• pp.577-586
• /
• 2015

The combination of voltage feedforward and feedback control is a conventional approach for correcting the power factor in single-phase ac-dc boost converters. The feedback duty ratio increases significantly with an increase of the line frequency and input inductance. Therefore, the performance of the conventional approach is highly dependent on the bandwidth of the feedback controller. As a result, the input power quality can be significantly exacerbated due to uncompensated duty ratios if the feedback controller is limited. This paper proposes an input impedance and current feedforward control method to reduce the control portion of the feedback controller. The findings in this paper are 1) the theoretical derivation and analysis of variations of line frequency and input inductance on a power factor correction approach, 2) guaranteed consistent performance in a wide range of conditions, and 3) that a low switching frequency can be utilized by the proposed method. A MATLAB/Simulink model and a 1.2kW dual boost converter are built to demonstrate the effectiveness of the proposed method.