• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.3
• /
• pp.219-224
• /
• 2011

Aluminum or CFRP is representative one of the lightweight materials. Collapse behavior of Al/CFRP square structural member was evaluated in this study based on the respective collapse behavior of aluminum and CFRP member. Al/CFRP square structural members were manufactured by wrapping CFRP prepreg sheets outside the aluminum hollow members in the autoclave. Because the CFRP is an anisotropic material with mechanical properties, The Al/CFRP square structural members stacked at different angles(${\pm}15^{\circ}$, ${\pm}45^{\circ}$, ${\pm}90^{\circ}$, $90^{\circ}/0^{\circ}$ and $0^{\circ}/90^{\circ}$ where the direction on $0^{\circ}$ coincides with the axis of the member) and interface numbers(2, 3, 4, 6 and 7). The axial impact collapse tests were carried out for each section members. Collapse mode and energy absorption characteristics of the each member were analyzed.

• Publications of The Korean Astronomical Society
• /
• v.30 no.2
• /
• pp.487-488
• /
• 2015

In type Ia supernovae (SNe Ia) cosmology, a well-established correlation exists between the mass of host galaxies and the Hubble residual (HR) of SNe Ia. In order to investigate the origin of this correlation, we used low-resolution spectroscopic data of early-type host galaxies obtained from our YOnsei Nearby Supernovae Evolution Investigation (YONSEI) project. We measured velocity dispersions and Lick/IDS absorption line indices from these fully calibrated spectra. These indices were used to estimate the luminosity-weighted mean age, metallicity and mass of host galaxies. We found a tight correlation between host mass and population age, which is consistent with the "downsizing" trend in early-type galaxies. This suggests that the well-established correlation between HR and host mass is most likely due to the difference in population age. More observations, which are in progress, are required to understand the impact of luminosity evolution on SNe Ia cosmology.

• Journal of Yeungnam Medical Science
• /
• v.23 no.1
• /
• pp.10-18
• /
• 2006

Epithelial to mesenchymal transition (EMT) is an important etiologic factor for the development of peritoneal fibrosis in CAPD patients. Mesothelial cells are main source of trans-differentiated fibroblasts under stress from the bioincompatible peritoneal dialysate. In our study there was no difference in dialysate TGF-${\beta}$ and VEGF between the low and high GDP groups during an initial 12 months. However, after adjusting with D-CA125, the low GDPs group showed a significantly lower D-TGF-${\beta}$/D-CA125 and D-VEGF/CA125 during the initial 12 months. Among the adjusted peritoneal growth factors for CA125, VEGF/CA125 and TGF-b/CA125 were factors significantly associated with greater EMT in this study. Adjustment of the peritoneal growth factor for effluent CA125 (surrogate for mass of HPMCs) revealed significant association with EMT suggesting that the fibroblastoid transition from HPMCs could be affected by the amount of intraperitoneal growth factors (TGF-b, VEGF) per unit mass of HPMCs. There was significant improvement in both cell score and D-CA125 at the sixth and 12th months after switching from a high GDPs solution to a low GDPs solution. Use of icodextrin solution in patients who had average peritoneal transport showed not only better systemic effects such as decreased glucose absorption via dialysate but also preservation of the peritoneum, including less EMT and high mesothelial bulk mass. In conclusion, Therapy with low GDP solution including icodextrin may positively impact preservation of the peritoneal membrane integrity and prevention of peritoneal fibrosis with time on PD.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.3
• /
• pp.41-48
• /
• 2019

The industrial safety helmets are personal protective equipment (PPE), used to protect the head against falls from a height. This study indicated the necessity of wearing a safety helmet while working at heights below 4 m, through analysis of fall accidents occurring in the industrial field. The stress, displacement, and strain of the safety helmet shell structure have been analyzed using the finite element method with various thicknesses, engineering plastics, and designs. It was preferred that the safety helmet shell structure had a reinforcement frame of uniform thickness in terms of increased impact strength and strain energy absorption rate. The thickness can be reduced to lighten the total weight for workers wearing safety helmets.

• Journal of Sensor Science and Technology
• /
• v.28 no.4
• /
• pp.236-239
• /
• 2019

In this work, we performed an optical simulation study on the performance of a PMDPP3T:PCBM based on an organic photovoltaic (PV) device. The virtual PV device was developed in Lumerical, finite-difference time-domain (FDTD) solutions. Different layers of the PV cell have been defined through the incorporation of complex refractive index value of those layers' constituent materials. During the simulation study, the effect of the variation active layer thickness on an ideal short circuit current density ($J_{sc,ideal}$) of the PV cell has been, first, observed. Thereafter, we have investigated the impact of surface roughness of a transparent conducting oxide (TCO) electrode on $J_{sc,ideal}$ of the PV cells. From this simulation, it has been observed that the $J_{sc,ideal}$ value of the PV cell is strongly dependent on the thickness of its active layer and the photon absorption of the PV cell has gradually decreased with the increment of the TCO's surface roughness. As a result, the capability of the PV device has been reduced with the increment of the surface roughness of the TCO.

• Advances in concrete construction
• /
• v.13 no.4
• /
• pp.291-305
• /
• 2022

The present investigation deals with the production of the innovative lightweight fly ash angular aggregates (FAA) first time in India using local class 'F' fly ash, its characterization, and exploring the potential for its utilization as alternative coarse aggregates in structural concrete applications. Two types of aggregates are manufactured using two different kinds of binders. The manufacturing process involves mixing fly ash, binder, and water, followed by the briquetting process, sintering and crushing them into suitable size aggregates. Tests are conducted on fly ash angular aggregates to measure their physical properties such as crushing value, impact value, specific gravity, water absorption, bulk density, and percentage of voids. Study shows that the physical parameters are significantly enhanced as compared to commercially available fly ash pellets (FAP). The developed FAA are used in concrete vis-à-vis conventional granite aggregates and FAP to determine their compressive, split tensile and flexural strengths. Although being lightweight, the strength parameters for concrete containing FAA are well compared with conventional concrete. This might be due to the high pozzolanic reaction between fly ash angular aggregates and cement paste. Also, RCC beams are cast and the load-deflection behaviour and ultimate load carrying capacity signify that FAA can be suitably used for RCC construction. Hence, the utilization of fly ash as angular aggregates can reduce the dead load of the structure and at the same time serves as a solution for fly ash disposal and mineral depletion problem.

• Korean Journal of Agricultural Science
• /
• v.49 no.3
• /
• pp.441-450
• /
• 2022

This study explored the effects of milk flavor (MF) supplementation on growth efficiency, nutrient absorption, fecal score, and blood profiles in weaning piglets. A total of 80 (21 days old) crossbred ([Yorkshire × Duroc] × Landrace) healthy weaned piglets with an initial body weight (BW) of 7.05 ± 1.22 kg were randomly allotted to one of two nutritive treatments with 8 repetitions and five pigs (2 female and 3 male) per pen. The experiment was divided into 2 phases (d 0 - 21, and d 21 - 42), and the dietary treatments consisted of TRT1, basal diet, TRT2 and basal diet + 1.0 g·kg^-1 MF. At days 21 - 42 and the overall period, the average daily gain (ADG) and average daily feed intake (ADFI) increased (p < 0.05) by receiving the MF added feed. However, MF inclusion did not impact (p > 0.05) the feed efficiency (G : F) throughout the entire experiment. Piglets consuming the MF supplemented diet showed that the apparent total tract digestibility of dry matter (DM), nitrogen (N) and energy (E) did not vary significantly (p > 0.05) between the treatments. All through the experiment, the fecal score and blood profile of the piglets fed the flavor diet also remained unaffected (p > 0.05). In conclusion, MF addition to the diet of the piglets increased their body weight and had no adverse effects on nutrient utilization, fecal score, and blood profile. Thus, MF addition could improve the performance outcomes of weaning piglets.

• Design & Manufacturing
• /
• v.16 no.4
• /
• pp.7-16
• /
• 2022

A helmet is essential for safety when operating personal mobility. However, user's actual helmet wear rate is low due to the inconvenience of wearing and poor ventilation. In this study, a new helmet structure with improved ventilation for personal mobility devices was designed. To design a new structure with improved breathability compared to the existing helmet while satisfying the safety regulations for the helmet, a generative design method was applied to the shock-absorbing liner of the helmet. In addition, other materials were applied to create a structure with improved ventilation while maintaining safety. The generated design result was verified for shock absorption through simulation. As a result of the study, EPS, the current material was replaced with CFRP and Kevlar, and the structure was changed. This design was judged to satisfy safety regulations against impact. The new helmet structure is expected to improve the helmet usability for personal mobility and increase the helmet wear rate of users.

• Advances in concrete construction
• /
• v.13 no.2
• /
• pp.133-152
• /
• 2022

Ecological issues such as natural resource reduction and enormous waste disposals are increasingly leading in developing civilization toward sustainable construction. The two primary environmental issues are the depletion of natural resources and the disposal of trash in open landfills. Waste steel fiber (WSF) was investigated for usage as a cement-based concrete (CBC) constituent in this research. Recycling waste fibers both makes cement composites more long and cost-effective, also aids in pollution reduction. The objective of this study is to analyze the impacts of waste fiber on the fresh and mechanical features of concrete using recycled additives. A comparative research on the durability and mechanical qualities of fiber-reinforced concrete (FRC) constructed with natural aggregates was conducted for this aim. The obstacles to successful WSF recycling methods application in the building industry have been investigated, resulting that CBCs with these fibers make an economic and long lasting choice to deal with waste materials. The workability of fiber enhanced concrete was found to be comparable to that of normal concrete. Fibers have a considerable impact on the splitting tensile strength, flexural and compressive strength of recycled concrete. Fiber may enhance the water permeability. When the WSF content is 0.6 kg/m3, the water absorption is nearly half. Fibers would have no effect on its permeability.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.05a
• /
• pp.123-124
• /
• 2021

Recently, the danger of fine dust has emerged worldwide. In general, fine dust refers to particulate matter less than 10㎛ and ultrafine dust less than 2.5㎛, and according to the announcement by HEI (Health Impact Research Institute) in 2015, the concentration of ultrafine dust in Korea is the second highest among OECD member countries. It was investigated. In this study, an experiment was conducted to analyze how the diatomaceous earth substitution rate affects the strength characteristics of the permeable block. As the replacement rate of diatomaceous earth increased, the strength decreased. The reason why the strength decreases with the use of diatomaceous earth is that the strength of the hardened body decreases as the structure of the hardened body becomes less dense as the amount of diatomaceous earth increases, and the reason that the strength decreases as the replacement rate of diatomaceous earth increases is the reason for the absorption performance of diatomaceous earth. Therefore, it is judged that a void was generated inside the hardened body while water was absorbed and then evaporated or discharged in the matrix, and accordingly, the strength decreased.