• IEIE Transactions on Smart Processing and Computing
• /
• v.5 no.3
• /
• pp.207-214
• /
• 2016

Optical communication systems are rapidly spread following increases in data traffic. In this work, a 32-Gb/s inductorless output buffer circuit with adjustable pre-emphasis is proposed. The proposed circuit consists of an output buffer circuit and an emphasis circuit. The emphasis circuit emphasizes the high frequency components and adds the characteristics of the output buffer circuit. We proposed a design method using a small-signal equivalent-circuit model and designed the compensation characteristics with a 65-nm CMOS process in detail using HSPICE simulation. We also realized adjustable emphasis characteristics by controlling the voltage. To confirm the advantages of the proposed circuit and the design method, we fabricated an output buffer IC with adjustable pre-emphasis. We measured the jitter and eye height with a 32-Gb/s input using the IC. Measurement results of double-emphasis showed that the jitter was 14% lower, and the eye height was 59% larger than single-emphasis, indicating that our proposed configuration can be applied to the design of an output buffer circuit for higher operation speed.

• The Journal of the Acoustical Society of Korea
• /
• v.36 no.2
• /
• pp.123-129
• /
• 2017

In this paper, the realization of a directional digital hearing aid was considered. Conventional time domain time delay method was replaced with digital filters in order to make any general-purposed DSP (Digital Signal Processing) chip to produce the similar directivity pattern. Both the time delay algorithm and the digital filter algorithm were initially evaluated by Matlab (Matrix laboratory) for comparison, and it was confirmed by CSR 8675 Bluetooth DSP IC (Digital Signal Processing Integrated Circuit) chip firmware realization. Some remote control features by a smart phone was added to the smart hearing aid for user interface easiness.

• Preventive Nutrition and Food Science
• /
• v.8 no.3
• /
• pp.289-293
• /
• 2003

Antioxidant activity and nicotine degradation activity (NDA) of 21 medicinal herbs were determined by using a 1,1-diphenol-2-picrylhydrazyl (DPPH) method and a PLC/PRF5 human liver cell line method, respectively, to develop an anti-smoking aid. The highest and lowest antioxidant activities represented by $IC_{50}$/ value were 30 $\mu$g/mL of Eugenia caryophyllus and 3,270 $\mu$g/mL of Panax ginseng C. A. Meyer, respectively. Antioxidant activity of Eugenia caryophyllus was equal to 38.0$\pm$1.2 mg VCEAC(vitamin C equivalent antioxidant capacity)/ g herb. The highest and lowest NDA values were 1.81 of Astrgalus membranaceus Bunge and 1.01 of Raphani seed and Lespedeza tomentosa Sieb, respectively. Eleven medicinal herbs with high antioxidant activity and/or NDA were selected to make an herbal tea. The herbal tea had high antioxidant activity (50 $\mu$g/mL $IC_{50}$/ and 22.4$\pm$1.4 mgVCEAC/g) and NDA (1.243). The medicinal herb tea could help smokers quitting smoking by degrading and exhausting nicotine accumulated in body and removing reactive oxygen species.

• Journal of Broadcast Engineering
• /
• v.1 no.2
• /
• pp.152-164
• /
• 1996

This paper describes the hardware architecture and implementation trade-offs of the Grand Alliance HDTV video encoder system. The implemented video encoder accepts video in 1125 line(30Hz) interlaced format, and produces a bit-stream compliant with the motion picture experts group version 2(MPEG-2) standards. The encoder processing includes large- area motion estimation and an advanced rate control mechanism. To keep the system complexity realizable, we adopt a fast hierarchical motion estimation method and developed its hardware architecture. Furthermore an adaptive perceptual quantization method is adopted to improve the perceptual quality. The developed system Is based on the 4-way parallel processing architecture and is implemented by using programmable IC, memory IC, and special-purpose processors such as DCT and motion estimation processors.

• Journal of the Korean Institute of Gas
• /
• v.1 no.1
• /
• pp.95-100
• /
• 1997

In order to predict the elastic-plastic fracture toughness for metallic materials, Finite Element Method(FEM) was used for analysis of compact tension specimen. ASTM E399 test procedure was adopted for simulation of FEM. The Load-Crack Mouth Opening Displacement curve obtained from this analysis was used to detect the crack initiation point and determine the elastic-plastic fracture toughness $J_{IC}$. In order to prove the results, they were compared with the results from previous experiments and they agree with experimental results.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.2
• /
• pp.9-18
• /
• 2014

This paper proposes the fuzzy PI controller for maximum power point tracking(MPPT) control of photovoltaic system. The output characteristics of the solar cell are a nonlinear and affected by a temperature, the solar radiation. The MPPT control is a very important technique in order to increase an output and efficiency of the photovoltaic system. The conventional perturbation and observation(PO) and incremental conductance(IC) are the method which finding maximum power point(MPP) by the continued self-excitation vibration, and uses the fixed step size. If the fixed step size is a large, the tracking speed of maximum power point is faster, but the tracking accuracy in the steady state is decreased. On the contrary, when the fixed step size is a small, the tracking accuracy is increased and the tracking speed is slower. Therefore, this paper proposes the MPPT control using the fuzzy PI controller that can be improve a MPPT control performance. The fuzzy PI controller is adjusted a input of PI controller by fuzzy control and compensated a cumulative error of fuzzy control by PI controller. The fuzzy PI MPPT control is compared to conventional PO and IC MPPT method for various temperature and radiation condition. This paper proves the validity of the fuzzy PI controller using these results.

• Toxicological Research
• /
• v.18 no.3
• /
• pp.227-232
• /
• 2002

In order to find out the appropriate in vitro method for high correlation with in vivo, we com-pared the sensitivities of phototoxicity (PT) in vitro method between in human keratinocytes, HaCaT cells and in 3T3 fibroblast cells derived from Balb/c mice. Both cells were exposed to six known phototoxic chemicals : promethazine, neutral red, chlortetracycline, amiodarone, bithionol, 8-methoxypsoralen, or non-phototoxic chemical, ALS (ammonium laureth sulfate) and then irradiated with 5 J/$cm^2$ of UVA. Cell viability ($IC_{50}$ ) was measured by neutral red uptake (NRU) assay. The ratio of $IC_{50}$ value of chemicals in the presence and absence of UVA was determined by the cut-off value. The phototoxic potential of test chemicals in NRU assay was determined by measuring the photoirriation factor (PIF) with a cut-off value of 5. In both 3T3 and HaCaT cells, all known phototoxic chemicals were positive (over 5 of PIF value), except that bithionol was found to be non-phototoxic to HaCaT cells, and ALS, non-phototoxic chemical was negative. These results suggest that Balb/c 3T3 cell was more sensitive than HaCaT cell to predict phototoxicity potential.

• Journal of IKEEE
• /
• v.17 no.3
• /
• pp.254-259
• /
• 2013

The choice of labeled data in semi-supervised learning algorithm can result in effects on the performance of the resultant classifier. In order to select labeled data required for the training of a semi-supervised learning algorithm, VCNN(Vector Centroid Neural Network) is proposed in this paper. The proposed selection method of label data is evaluated on UCI dataset and caltech dataset. Experiments and results show that the proposed selection method outperforms conventional methods in terms of classification accuracy and minimum error rate.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.12
• /
• pp.4352-4360
• /
• 2011

A four dimensional quantitative structure activity relationship analysis was applied to a series of 50 flavonoid inhibitors of $p56^{lck}$ protein tyrosine kinase by the molecular comparative electron topological method. It was found that the -log (IC50) values of the compounds were highly dependent on the topology, size and electrostatic character of the substituents at seven positions of the flavonoid scaffold in this study. Depending on the negative or positive charge of the groups correctly embedded in these substituents, three-dimensional bio-structure to increase or decrease -log (IC50) values in the training set of 39 compounds was predicted. The test set of 11 compounds was used to evaluate the predictivity of the model. To generate 4D-QSAR model, the defined function groups and pharmacophore used as topological descriptors in the calculation of activity were of sufficient statistical quality ($R^2$ = 0.72 and $Q^2$ = 0.69). Ligand docking approach by using Dock 6.0. These compounds include many flavonoid analogs, They were docked onto human families of p56lck PTKs retrieved from the Protein Data Bank, 1lkl.pdb.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.5
• /
• pp.474-481
• /
• 2009

Fracture models and criteria of adhesive with two parameters, namely $G_C$ and ${\sigma}_{max}$, have been developed to describe the fracture process of adhesive joints. Cohesive zone model(CZM) is a representative two parameter failure criteria approach. In CZM, ${\sigma}_{max}$ is a critical, limiting maximum value of the stress in the damage zone ahead of the crack and is assumed to have some physical significance in adhesive failure. Based on CZM and finite element analysis method, the relationship between fracture load and adhesive properties, as $G_{IC)$ and $({\sigma}_{max})_I$, was investigated in adhesively bonded joint tensile test and T-peel test. The two parameters in tensile mode loading were evaluated by using the relationship. The value of $G_{\IC}$ evaluated by proposed method showed close agreement with analytical solution for tapered double cantilever beam(TDCB) test which proposed in an ASTM standard.