• 한국구조물진단유지관리공학회 논문집
• /
• 제18권6호
• /
• pp.11-20
• /
• 2014

본 연구는 정현형 주름과 마름모형 주름 형상의 전단좌굴 특성을 비교, 분석하는 것이 목적이다. 이를 위해서 동일한 길이의 마름모꼴 주름과 정현파주름을 해석대상모델로 채택하였으며, 선형좌굴해석을 통한 전단좌굴특성과 이론식에 의한 특성을 분석하였다. 일반적으로 주름강판의 전단좌굴 형태는 국부좌굴, 전체좌굴 및 두 좌굴에 의한 연성좌굴로 분류된다. 그러나 마름모꼴주름과는 달리 정현파주름형상은 평평한 면이 없기 때문에 전단좌굴의 양상에 대한 경향이 달라진다. 특히 국부좌굴과 전체좌굴의 경계에서 나타나는 전단응력변화와 양상은 주름형태에 의해 차이가 난다. 분석 결과에서 볼 때, 제형 (마름모꼴)의 경우는 이론식내의 전체좌굴과 국부좌굴의 경계에서 연성좌굴모드가 발생했다. 그러나 정현파형의 경우 전체좌굴이 발생하는 구간에서 연성좌굴모드가 발생하는 양상을 보였다. 또한 국부좌굴 구간에는 제형형상이 그리고 전체좌굴 구간에서는 정현파형상이 전단좌굴에 저항하는데 유리하게 작용하였다.

• 한국주조공학회지
• /
• 제5권4호
• /
• pp.283-288
• /
• 1985

The melt of highly purified Zn was poured by top pouring process into the open green sand mold, that was made by using the 3-plane L-sections pattern. After skin was formed, the unsolified melt was poured out by rolling-over. The thicknesses of skin for each different of castings were investigated with one dimension. The results obtained and could be summerzed as follows: 1) While the 3-plant L-sections castings were solidifying in the mold, solidification blocks of different section modulus in the castings were formed, i.e. 1-dimension divergency block, 2-dimension heat divergency block, 3-dimension heat divergency block, 2-dimension heat convergency block, and 3-dimension heat convergency block. 2) When the chill plate was set up to the mold in order to change section modulus artificially, heat divergency blocks and heat convergency blocks according to the shape of chill plate were revealed.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2000년도 High Temperature Superconductivity Vol.X
• /
• pp.257-261
• /
• 2000

The value of I$_c$(critical current) in HTS (High Temperature Superconductor) tape has a great influence on B${\bot}$(vertical field). Therefore, in shape design of field coil for the HTSG(High Temperature Superconducting Generator), a method to reduce the B${\bot}$ should be considered in order to maintain the stability and substantial improvement on the performance. On the basis of the magnetic field analysis, this paper deals with various field coil shape according to the iron plate to obtain small B${\bot}$ by using Biot-Savart's law, image method and 2D FEA(2 Dimensional Finite Element Analysis) considering the stress condition of HTS. Moreover, the analysis is verified by comparison with experimental results. And also this paper presents the advanced model by using 3D FEA, in which flux density at armature is calculated in 5kVA class HTSG.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.800-803
• /
• 2002

This investigation describes and analyses the experimental results proper to the penetration of Al5052-H34 alloy plates of thickness 6, 12 and 16mm(T/D＝1, 2, 3) by 5.56mm ball projectiles over the velocity range 350-750㎧. All the high velocity impact tests were carried out at normal impact angle, i.e. zero obliquity. The experimental results presented the variation of depth of penetration, bulge height and diameter, plugged length and diameter with the velocity fur tests on each plate of a given thickness in order to determine the deformation shapes of 5.56mm ball projectiles and targets. Also the protection ballistic limit($V_50$) tests were conducted.

• Tribology and Lubricants
• /
• 제29권3호
• /
• pp.186-191
• /
• 2013

Hydraulic systems are used to transform mechanical energy into fluid energy and vice versa. They are widely applied in various industries; e.g., they are used in automobiles, public works, rockets, machine tools, heavy construction equipment, and airplanes. Hydraulic pumps are used to transform the energy in these systems. In this study, with the basic operation principles as a starting point, I attempted to clarify how the shape of a slipper affects the lubrication characteristics under practical conditions. A swashplate with a tilt angle of zero and capable of rotating motion was used, along with other devices. A slipper was located at 45 mm eccentricity from the center of the swashplate. The results of this experiment indicated that the shape of the bottom surface of a slipper affects the load capacity, leakage flow, and lubrication characteristics and that the slipper is one of the most important parts for improving the pump efficiency.

• 설비공학논문집
• /
• 제9권3호
• /
• pp.292-299
• /
• 1997

Ammonia has been used as refrigerant for more than 100 years in absorption as well as in compression systems. Due to its poisonous and inflammable properties, however, its use has been mainly on heavy industrial plants in which regular maintenance are available. For these systems, condensers are generally water-cooled. This is suitable for large systems over 20 RT but is not suitable for small systems. In order to apply ammonia for a small system, it is important to adopt an air-cooled condenser. In this study, simple numerical analysis of an air-cooled condenser for an ammonia refrigeration system has been carried out. The condenser is designed as horizontal tubes with plate fins attached at the outer surface to enhance the air-side heat transfer rate. Effects of fin shape and arrangement are studied in detail. Since the local heat transfer coefficient is highest at the leading edge, heat flux is highest at the edge and decreases along the distance. Conditions of inlet air are also varied in the study and condenser length that is required for full condensation is calculated. The results show that it is important to enhance both the air-side and internal heat transfer coefficients.

• 한국가시화정보학회지
• /
• 제10권1호
• /
• pp.21-26
• /
• 2012

Hydrophobic characteristics of high temperature metal surface were investigated by high-speed visualization of water droplet impact. An aluminum plate was used as the sample plate and the initial diameter of a water droplet was 2 mm. Transient behavior of a single droplet impinging on the surface with and without heating was captured by using a high speed camera running at 4,000 frames per second. The Leidenfrost phenomenon was demonstrated for the case of $300^{\circ}C$ surface temperature, however there was no rebounding of droplet on the cold plate due to hydrophilic nature. The experimental results show that the shape evolution of a droplet impinging on the surface varies with the Weber number, i.e. the ratio of impact inertia to capillary force. The overall water-repellent characteristics of the heated surface was very similar to that of the super hydrophobic surfaces.

• 대한기계학회논문집A
• /
• 제27권4호
• /
• pp.601-607
• /
• 2003

The column type is used as the sensing element of the load cell to measure the large force in the range of 10$^4$~ 10$^{7}$ N. However. it is not easy to handle the load with large capacity due to its size. It is, therefore, necessary to design a compact load cell with a low aspect ratio. Thus this paper showed the characteristic evaluation of compact load cell with respect to the shape of supporting plate. The supporting plate of the load cell was an annular type with inner(D$_{i}$) and outer(D$_{o}$) diameters. Using the strain distribution obtained from FEM. the supporting plate was designed to get the stable output voltage of the load cell. The three designed supporting plates were manufactured, and the result of characteristic experiment of the load cell, using the 10 MN hydraulic force standard machine, was compared with FEM.M.M.

• 한국항공우주학회지
• /
• 제37권9호
• /
• pp.829-836
• /
• 2009

말굽와류로 대표되는 3차원 유동현상은 필연적으로 주유동에 대한 2차 유동의 형태로 발생되며, 유동손실을 유발하게 된다. 본 논문에서는 2차유동 손실을 일으키는 주요 요인중의 하나인 말굽와류의 강도를 감쇄시키기 위해 일반적인 날개 앞전에 설치한 판에 대해, 판의 설치 높이, 길이, 폭 및 두께 등의 형상변수를 설계변수로 정하여 이를 최적화하였다. 근사최적설계 기법을 이용 최적화를 수행하였으며, $FLUENT^{TM}$와 $iSIGHT^{TM}$를 이용하였다. 최적화 수행결과, 기준 모델의 경우보다 전압력 계수가 약 7.5% 감소하였다.

• Smart Structures and Systems
• /
• 제25권2호
• /
• pp.241-254
• /
• 2020

Using confined shape memory alloy (SMA) bar or plate, this study proposes an innovative self-centering damper. The damper is essentially properly machined SMA core, i.e., bar or plate, that encased in buckling-restrained device. To prove the design concept, cyclic loading tests were carried out. According to the test results, the damper exhibited desired flag-shape hysteretic behaviors upon both tension and compression actions, although asymmetric behavior is noted. Based on the experimental data, the hysteretic parameters that interested by seismic applications, such as the strength, stiffness, equivalent damping ratio and recentering capacity, are quantified. Processed in the Matlab/Simulink environment, a preliminary evaluation of the seismic control effect for this damper was conducted. The proposed damper was placed at the first story of a multi-story frame and then the original and controlled structures were subjected to earthquake excitations. The numerical outcome indicated the damper is effective in controlling seismic deformation demands. Besides, a companion SMA damper which represents a popular type in previous studies is also introduced in the analysis to further reveal the seismic control characteristics of the newly proposed damper. In current case, it was found that although the current SMA damper shows asymmetric tension-compression behavior, it successfully contributes comparable seismic control effect as those having symmetrical cyclic behavior. Additionally, the proposed damper even shows better global performance in controlling acceleration demands. Thus, this paper reduces the concern of using SMA dampers with asymmetric cyclic behavior to a certain degree.