• Steel and Composite Structures
• /
• 제18권4호
• /
• pp.873-887
• /
• 2015

The continuous composite I-girder should have a sufficient rotation capacity (or ductility) to redistribute the negative bending moment into an adjacent positive bending moment region. However, it is generally known that the ductility of the high strength steel is smaller than that of conventional steel, and application of high strength steel can cause ductility problems in a negative moment region of the I-girder. In this study, moment redistribution of the continuous composite I-girder with high strength steel was studied, where high strength steel with yield stress of 690 MPa was considered (the ultimate stress of the steel was 800 MPa). The available and required rotation capacity of the continuous composite I-girder with high strength steel was firstly derived based on the stress-strain curve of high strength steel and plastic analysis, respectively. A large scale test and a series of non-linear finite element analysis for the continuous composite I-girder with high strength steel were then conducted to examine the effectiveness of proposed models and to investigate the effect of high strength steel on the inelastic behavior of the negative bending moment region of the continuous composite I-girder with high strength steel. Finally, it can be found that the proposed equations provided good estimation of the requited and available rotation capacity of the continuous composite I-girder with high strength steel.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2008년도 정기 학술대회
• /
• pp.585-588
• /
• 2008

Resistance to lateral torsional buckling of steel I-girder (open section) is a very important design requirement. But, most studies of steel I-girder with corrugated webs were invested in shear behavior. Until now, most studies about Lateral torsional buckling of I-girder with corrugated webs have been based on Lindner.J's study. the study includes that the pure torsional constant of I-girder with corrugated webs doesn't different from that of I-girder with flat webs. This paper pesents pure torsional constant I-girder with sinusoidally corrugated webs by using finite element analysis.

• 한국구조물진단유지관리공학회 논문집
• /
• 제10권6호
• /
• pp.143-153
• /
• 2006

본 연구에서는 지점부 단면형고 확대를 도입한 연속 프리스트레스트 Steel I-Girder의 휨거동 특성을 파악하고자 하였다. 긴장력 도입 후 정적 휨 재하실험을 수행 하여 지점부 단면형고 확대도입 및 강연선의 배치양상, 도입된 긴장력을 실험변수로 하여 그에 따른 내하력 향상정도를 평가하였다.

• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2008년도 정기총회 및 학술발표대회
• /
• pp.287-290
• /
• 2008

Resistance to lateral torsional buckling of steel I-girder (open section) is a very important design requirement. But, most studies of steel I-girder with corrugated webs were invested in shear behavior. Untill now, most studies about Lateral torsional buckling of I-girder with corrugated webs have been based on Lindner.J's study (Lateral torsional buckling of beamswith trapezoidally corrugated webs,1990). the study includes that the pure torsional constant of I-girder with corrugated webs $J_{cor}$ doesn't different from that of I-girder with flat webs. This paper pesents pure torsional constant of I-girder with corrugated webs by using finite element anaysis.

• 콘크리트학회논문집
• /
• 제27권4호
• /
• pp.377-385
• /
• 2015

PSC I 거더의 장경간화는 단면의 세장비와 자중의 영향 등을 증가시켜 거더의 횡적 불안정에 대한 위험성을 높였다. 특히 최근에는 시공 중 거더의 전도 붕괴사고가 증가하고 있어 거더의 횡적 불안정성에 대한 평가 기술이 절실히 요구되고 있다. 따라서, 본 연구에서는 시공 중 전도 붕괴의 한 원인으로 판단되어지고 있는 풍하중에 대하여 PSC I 거더의 횡방향 거동 특성과 안정성을 평가하였다. 거더의 횡방향 불안정성은 주로 거더의 길이와 받침의 강성 변화에 의해 영향을 받는다. 해석결과에 의하면 거더의 경간장이 증가함에 따라 거더의 횡적 불안정성을 유발할 수 있는 임계 풍하중은 감소하고, 거더의 변형과 회전각, 받침의 회전각은 모두 증가하였다. 최종적으로 시공 시 PSC I 거더의 임계 풍하중과 임계 횡변위량을 계산할 수 있는 해석식을 제시함으로써, 시공 시 거더의 횡적 안정성을 유지하기 위한 정량적 관리 수치를 제공할 수 있으리라 판단된다.

• 한국강구조학회 논문집
• /
• 제23권2호
• /
• pp.221-228
• /
• 2011

강 판형교는 높은 세장비 때문에 좌굴이 설계의 주요 변수이다. 본 연구의 목적은 I 형 플레이트 거더와 파형 복부판을 갖는 플레이트 거더의 좌굴거동을 분석하고, 파형 복부판을 갖는 플레이트 거더의 이점을 조사하는 것이다. 파형 복부판 깊이의 변화, 복부판의 두께 변화 그리고 하중조건의 변화에 따라 다양한 파라미터 연구를 수행하였다. 연구의 결과로서 파형 복부판을 갖는 플레이트 거더의 좌굴강도가 I 형 플레이트 거더에 비해서 좌굴강도에 있어서 46%~417% 더 효과적이며, 파형 복부판을 갖는 플레이트 거더의 적절한 파형각도는 ${\theta}=15^{\circ}{\sim}22^{\circ}$로 나타났다.

• 콘크리트학회논문집
• /
• 제12권6호
• /
• pp.13-22
• /
• 2000

In order to resolve the problem of increasing traffic entailed by the economic development, road system is reorganization and new highways are built, and long span bridges over 40m are being constructed in environmental and aesthetic considerations. Most long span bridges that are currently being constructed are in general steel box girder and preflex girder bridges; however these types of breiges are less efficiency than PSC I-type girder bridges in terms of construction cost and maintenance. Therefore, in these study, structural efficiency of PSC I-type girders based on section parameters, concrete compressive strength and other design parameter is observed to develope new PSC I-type girder for long span bridges. As a results of analysis, most important design parameters that control the stress of the girder are found to be the top flange width and the height of girder. In this light, the relationship between the two variables is determined and cross-section details of the girder that most appropriates for the long span bridges are proposed. The use of high strength concrete appears to increase the general design span however the increase rate of the span from increasing concrete ultimate strength appears to be reduced depending on the span. Also, the optimal girder spacing is determined through the parameter studies of design span using the proposed girder.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.507-512
• /
• 2002

Prestressed concrete I-girders were used in the bridge applications in the early 1950s. During the last four decades, the most widely used girder length of bridges have been below 30 meters. The main objective of this study is to develope the alternative section for widely spaced girder of 30 meters span bridge. Girder spacing, the number of strands and compressive strength of concrete are major parameters for widely spaced girders. The optimal girder spacing is determined through the parameter studies of design using widely spaced girders. 30m span bridges of widely girder spacing must use high-strength concrete. Although the basic unit cost of concrete is higher for high-strength concrete, it may be partially or even fully offset by reduced quantities of concrete as result of the smaller number of girders used. High-strength concrete girders have more prestressing strands per girder, but the total number of strands for all of the girders is less than that required for the larger number of normal-strength concrete girders. It could design PSC-I Birdge with widely spaced girder owing to high-strength concrete.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.262-267
• /
• 2008

The type used mainly in present our country in the superstructure of the railway bridge including the high speed railway is classified by the box girder and the I-type girder, greatly. The box girder is mainly used by the high speed railway bridge, and the I-type girder is used mostly by general railway bridge style. In this study, according to current railway bridge design code, we execute design by the span length of each considered bridge form. Also we analyze the suitable girder height by the span length and calculate the construction costs. The comparative analysis of the structural efficiency is produced by the span length. From this study, it is exposed that the girder height by the span length is the biggest in box girder. Also it is evaluated that the construction costs of the box girder is higher than that of the I-type girder although there is a difference between more or less according to adopted construction method.

• Steel and Composite Structures
• /
• 제42권1호
• /
• pp.139-149
• /
• 2022

To simplify the design and reduce the construction cost of traditional multi-girder structural systems, twin I-girder structures are widely used in many countries in recent years. Due to the concern on post-fracture redundancy, however, twin girder bridges are currently classified as fracture critical structures in AASHTO specifications for highway bridges. To investigate the after-fracture behavior of such structures, a composite steel and concrete twin girder specimen was built and an artificial fracture through the web and the bottom flange was created on one main girder. The static loading test was performed to investigate its mechanical performance after a severe fracture occurred on the main girder. Applied load and vertical displacement curves, and the applied load versus strain relationships at key sections were measured. To investigate the load distribution and transfer capacities between two steel girders, the normal strain development on crossbeams was also measured during the loading test. In addition, both shear and normal strains of studs were also measured in the loading test to explore the behavior of shear connectors in such bridges. The functions and structural performance of structural members and possible load transfer paths after main girder fractures in such bridges were also discussed. The test results indicate in this study that a typical twin I-girder can resist a general fracture on one of its two main girders. The presented results can provide references for post-fracture performance and optimization for the design of twin I-girder bridges and similar structures.