• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.258-263
• /
• 2005

The nearest variety of the industrial world requires using the high precision and resolution positioning technology to do a semi-conductor, information field , and measurement field. It is especially important for the positioning technology that makes up a proper controller, is affected by the minimal heat and vibration, and can control a structurally generated non-linear friction factor to determine the efficiency of the system. The paper is to analyze the vibration characteristic according to the speed of linear motor and grasp the dynamic characteristic through the modal test and show the verification of the experimental result and design parameters by using FEM(Finite Element Method). Also, it shows the optimum standard analyzed the acceleration patterns of the moving part that lead to the vibration source in linear motor. It presents the analyzed dynamic of linear motor in compliance with a change of the non-linear factor.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.9
• /
• pp.1227-1232
• /
• 2014

The purpose of this paper is to establish the optimum fabricating condition of specimens using silk screen printing, and to develop humidity sensor which has good humidity sensing properties. The specimens are fabricated under the condition of 90[wt%] $SnO_2$-10[wt%] $TiO_2$, and their microstructure, crystalline structure, humidity sensing properties are examined. From the microstructure analyses, porosity is best at 700[$^{\circ}C$]. From the crystalline structure analyses, intensity of peak becomes strong according to increasing heat treatment temperature. From the humidity sensing properties analyses, an overall results of capacitance changes, linearity and hysteresis for the specimens is best at 600[$^{\circ}C$] and 700[$^{\circ}C$]. Capacitance of specimens increases according to decreasing measurement frequency, and to increasing relative humidity.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.14 no.1
• /
• pp.1-15
• /
• 1996

In this paper, the preparation of lead zirconium titanate(PZT) thin film by sol-gel processing was descried. Thin film coated with thickness of 4${\mu}{\textrm}{m}$ on the stainless steel substrates using the multiple spin-coating process. The crystalline phases of PZT powder and film were investigated by X-ray diffraction pattern and PZT thin film has perovskite structure over 600 C annealing temperature. Corona charging characteristics of the ferroelectric PZT thin film at 600 C were investigated by electrophotographic measurement. A difference in the charging characteristics between positive and negative corona charging was found. The charge acceptance depended in the polarity of corona and the poling of film. According to the D-E hysteresis measurment, PZT thin film can be poled by corona charging without use of top electrode. The remnant polarization in the PZT thin film is generally in the order of 48$\mu$C/$\textrm{cm}^2$. From this results, the ferroelectric PZT thin film will be possible to apply for the add-on type imaging formation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.368-369
• /
• 2006

Ferroelectric thin films have attracted much attention for applications in nonvolatile ferroelectric random access memories(NVFeRAM) from the view points of high speed operation, low power consumption, and large scale Integration[1,2]. Among the FRAM, BLT is of particular interest. as it is not only crystallized at relatively low processing temperature, but also shows highly fatigue resistance and large remanent polarization Meanwhile, these submicron ferroelectric capacitors were fabricated by a damascene process using Chemical mechanical polishing (CMP). BLT capacitors were practicable by a damascene process using CMP. The P-E hysteresis were measured under an applied bias of ${\pm}5V$ by using an RT66A measurement system. The electric properties such as I-V were determined by using HP4155A analysers.

• Applied Science and Convergence Technology
• /
• v.25 no.4
• /
• pp.77-80
• /
• 2016

The $PbSc_{1/2}Nb_{1/2}O_3$ ceramics at a relatively low temperature of $1300^{\circ}C$ was successful synthesized. Solid state reaction of two-step process is not necessary. The dielectric constant, dielectric loss and admittance of ceramic samples were determined. The pyroelectric characteristics are in good agreement with the dielectric properties. Ferroelectric properties of well-formed the $PbSc_{1/2}Nb_{1/2}O_3$ ceramics are in agreement with broad distribution of relaxation phenomenon. Relatively strong frequency dependent of dielectric constant is observed at about $110^{\circ}C$. The distinct thermal hysteresis was observed in the measurement of the dielectric constant and dielectric loss. The critical exponents of during cooling and heating measurements in the $PbSc_{1/2}Nb_{1/2}O_3$ ceramics were 1.14 and 1.59 at 1 kHz, respectively.

• Korean Journal of Materials Research
• /
• v.12 no.2
• /
• pp.135-139
• /
• 2002

Carbon powders (CP) and carbon fiber (CF) were introduced info glass fiber reinforced plastics (FRP) composites to obtain fracture detection function. The composites were evaluated through the relation between a load-displacement curve and an electrical resistance change curve in three point bending test. CP containing FRP (CP-FRP) has a sensitivity of electrical resistance change at much lower load level than CF containing FRP (CF-FRP). In loading-unloading tests, CP-FRP showed a large amount of residual electrical resistance which enables the estimation of loading hysteresis.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1117-1122
• /
• 2003

The paper on table deflection by stop state and move speed at loaded load, and the table deflection measured of static load. It is developed program for Date correction of LSM(Least Square Method). We experimented the method as following. The first a Laser setting and scan Experimental device measured curvature radius, The second A center of measurement object and curvature radius taking of LSC.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.138-139
• /
• 2008

An iron-cored voltage transformer(VT) is usually used to obtain the standard low voltage signal for protection and measurement. Generally, the iron-cored transformers have errors due to the hysteresis characteristics of the iron-core. An error compensating algorithm for iron-cored instrument transformer can improve the accuracy of conventional voltage transformers. This paper describes the iron-cored electronic voltage transformer having the error compensating algorithm. The innovative product composes an iron-cored VT and an intelligent electronic device(IED) having the error compensating algorithm. The test results of the iron-cored electronic voltage transformers in Korea Electro-technology Research Institute(KERI) are presented.

• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.729-733
• /
• 2003

This paper proposed a novel current control strategy on active power filters using p-q-r instantaneous power theory which can compensate the line current harmonics and the neutral line current in unbalanced and/or distorted source conditions in three-phase four-wire systems. The proposed current control method is based on a sinusoidal PWM for fully-digital implementation which was compared with a hysteresis PWM. Simulation results showed good performance of the proposed current control strategy on shunt type APFs.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1995.03a
• /
• pp.40-62
• /
• 1995

A micro positioning system using piezoelectric actuators have very wide application region such as ultra-precision machine tool optical device measurement system. In order to keep a high precision displacement resolution it to useful to take a position sensor and feedback of the error. From the practical point of view high-resolution displacement sensor systems are very expensive and it is difficult to make such a sensitive sensor work properly in a poor operational environment of industry. In this study a piezo-electric micro-depth control system which does not require position sensor but piezoelectric voltage feedback has been developed. It is driven by hysteresis-considering reference input voltage calculated in advance and actuator/sensor characteristics of piezoelectric materials. From the result of experiments a fast and stable response of micro-depth control system has been achieved and an efficient technique to control the piezoelectric actuator suggested.