• Journal of the Korean Society of Tobacco Science
• /
• v.3 no.1
• /
• pp.30-40
• /
• 1981

The moisture sorption and desorption isotherms of various tobaccos were obtained over a relative humidity range from 0 to 90% at $20^{\circ}C$ and $30^{\circ}C$. The hysteresis effect, constant and rate of moisture sorption and desorption, monomolecular-layer moisture content, and specific surface area were analyzed from the obtained data. The moisture sorption and desorption isotherms showed a different characteristics for different tobacco varieties. At a lower humidity range below 50% RH, Burley tobacco had higher moisture sorption and desorption figures than Hicks and Basma, while, at a higher humidity range above 50% RH, Hicks had higher values than the others. The hysteresis effect of tobacco were greater in an intermediate humidity range (40-70% RN), and Basma showed a greater effect than the others. The sorption and desorption constant (K) increased with temperature, but decreased with RH, and Burley tobacco had larger K values, while Hicks had smaller K values than others. The sorption and desorption rate of Burley tobacco were greater than the other tobaccos. The monomolecular-layer moisture was 27.8 and 51.4mg/g, and the specific surface was 101 and $186m^2/g$, for Basma and Burley, respectively.

• Journal of Surface Science and Engineering
• /
• v.37 no.2
• /
• pp.110-118
• /
• 2004

The corrosion of pure titanium (CP- Ti Grade 2) and titanium alloy (Ti6Al4V ELI) were studied under various conditions of simulated body fluids. The static immersion test and the electrochemical test were performed in accordance with ISO 10271 : 2001. For the electrochemical test, the open circuit potential was monitored as a function of time, and the cyclic polarization curve was recorded. The corrosion resistance was evaluated from the values of corrosion potential, passivation current density, breakdown potential, and the shape of hysteresis etc. The effects of alloy type, surface condition, temperature, oxygen, and constituents in the fluids such as acid, chloride were estimated. Both specimens had extremely low dissolution rate in the static immersion test. They showed strong passivation characteristics in the electrochemical test. They maintained negligible current density throughout the wide anodic potential range. The passive layer was not broken up to 2.0 V (vs. SCE). The hysteresis and the shift of passivation potential toward the anodic direction was observed during the reversed scan. The passivation process appeared to be accelerated by oxygen in air or that dissolved in the fluids. The passivation also proceeded without oxygen by the reaction of constituents in the fluids. Acid or chloride in the fluids, specially later weakened the passive layer, and then induced higher passivation current density and less shift of passivation potential in the reversed scan. CP-Ti Grade 2 was more reactive than Ti6Al4V ELI in the fluids containing acid or chloride, but thicker layer produced on its surface provided higher corrosion resistance.

• Journal of Sensor Science and Technology
• /
• v.13 no.4
• /
• pp.287-291
• /
• 2004

A capacitive type humidity sensor has been fabricated using a polyimide film without hydrophobic elements and its characteristics has been evaluated for hermeticity measurement of micro packages. For a highly sensitive humidity sensor, a polyimide film without hydrophobic elements has been synthesized and used instead of using a commercial one in which 7 group elements such as fluorine or chlorine are included. Sensitivity, stability and hysteresis has been performed to characterize the fabricated sensors. The sensitivity defined as normalized percent capacitance change was 0.3751%RH and hysteresis was 0.77% in the range of 10%RH to 90%RH. Maximum deviation from the average capacitance measured for 120 minutes at 50%RH was 0.25%. The proposed humidity sensor can be used for hermeticity measurement of micro packages.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.27 no.8
• /
• pp.883-891
• /
• 2003

In this study, a change of hand of fabrics dyed with persimmon juice was measured using Kawabata Evaluation System. Using various cotton fabrics, linen fabric and silk fabric used frequently for persimmon juice dyeing, we examined the changes of physical properties and hand according to persimmon juice dyeing and washing. The dynamic characteristics of hand were measured tensile, shear, bending, compression, surface properties, thickness and weight. Linearity of load-extention and tensile resilience were increased in all kinds of fabrics after dyeing. Tensile energy decreased in cotton fabric 2(gauze), cotton fabric 3(muslin) and linen fabric. Shear stiffness and hysteresis of shear increased in most of fabrics. Bending rigidity of the bending property and hysteresis of bending, linearity of compression of the compression property, compression energy and compression resilience increased in all kinds of fabrics after dyeing. Thickness and weight increased much in all kinds of fabrics after dyeing. In the primary hand value, stiffness and anti-drape stiffness increased in all kind of fabrics after dyeing. The fullness and softness, crispness, scrooping feeling and flexibility with soft feeling decreased. As the stiffness after persimmons dyeing increased, it was suitable for clothes material of summer.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.2
• /
• pp.93-98
• /
• 2008

To investigate the characteristics of water droplet on the gas diffusion layer from both top-view and side-view of the flow channel, a rig test apparatus was designed and fabricated with prism attached plate. This experimental device is used to simulate the growth of single liquid water droplet and its transport process with various air flow velocity and channel height. The contact angle hysteresis and height of water droplet are measured and analyzed. It is found that droplet tends towards to be instable by decreasing channel height, increasing flow velocity or making GDL more hydrophobic. Also, the simplified force balance model matches with experimental data only in a restricted range of operating conditions and shows discrepancy as the air flow velocity and channel height increases.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.6
• /
• pp.493-501
• /
• 1998

$YBa_2Cu_3O_X$ samples were fabricated by MPMG(Melt Powdered Melt Growth). Intitial composition of the mixed powders were prepared as follow ; $YBa_2Cu_3O_X$ : $Y_2BaCuO_5$ = 1:0, 1:0.2, 1:0.3, 1:0.4. After the first melt and cooling, 5wt% to 20wt% fo Ag power was added to the powder. Effects of the different initial $Y_2BaCuO_5$ and Ag addition amount on $J_c$ and magnetization of $YBa_2Cu_3O_X$ fabricated by MPMG method were investigated. The critical current density increased with the amount of $Y_2BaCuO_5$ and Ag. It was also observed that the difference between negative and positive magnetization in the magnetization hysteresis measurement at 77K was larger than the case where $Y_2BaCuO_5$and Ag were not added to the $YBa_2Cu_3O_X$ powders. It is concluded that $Y_2BaCuO_5$ sample with 40wt% amount of $Y_2BaCuO_5$ and 20wt% amount of Ag has not only the largest $J_c$ but also the improved pinning effect.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.3
• /
• pp.205-212
• /
• 2002

The growth characteristics of metal-organic chemical vapor deposition (MOCVD) $Pb(Zr_xTi_{1-x})O_3 (PZT) thin films were investigated for the application of high-density ferroelectric random access memories (FRAM) devices beyond 64Mbit density. The supply control of Pb precursor plays the most critical role in order to achieve a reliable process for PZT thin film deposition. We have monitored the changes in the microstructure and electrical properties of films on increasing the Pb precursor supply into the reaction chamber. Under optimized conditions, $Ir/IrO_2/PZT(100nm)/Ir capacitor shows well-saturated hysteresis loops with a remanent polarization (Pr) of $~28{\mu}C/textrm{cm}^2$ and coercive voltage of 0.8V at 2.5V. Other issues such as step coverage, compositional uniformity and low temperature deposition was discussed in viewpoint of actual device application.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.297-298
• /
• 2005

We have fabricated twisted nematic (TN) liquid crystal cells doped by carbon nanotubes (CNTs) with different CNT wt. %. With a minute amount doping, multi-walled CNTs did not perturb the liquid crystal orientations at the off- and on-state. The hysteresis studies of voltage-dependent capacitance (V-C) under the influence of electric field generated by ac and dc voltage show that the residual do, which is tightly related to image sticking problem in liquid crystal displays, is greatly reduced due to ion trapping by CNTs. Also, the V-C hysteresis shows dependency of capacitance on concentration of multi-walled CNTs.

• Structural Engineering and Mechanics
• /
• v.64 no.4
• /
• pp.461-472
• /
• 2017

The dynamic tests of recycled aggregate concrete (RAC) are carried out, the rate-dependent mechanical models of RAC are proposed. The dynamic mechanical behaviors of RAC frame structure are investigated by adopting the numerical simulation method of the finite element. It is indicated that the lateral stiffness and the hysteresis loops of RAC frame structure obtained from the numerical simulation agree well with the test results, more so for the numerical simulation which is considered the strain rate effect than for the numerical simulation with strain rate excluded. The natural vibration frequency and the lateral stiffness increase with the increase of the strain rate. The dynamic model of the lateral stiffness is proposed, which is reasonably applied to describe the effect of the strain rate on the lateral stiffness of RAC frame structure. The effect of the strain rate on the structural deformation and capacity of RAC is analyzed. The analyses show that the inter-story drift decreases with the increase of the strain rate. However, with the increasing strain rate, the structural capacity increases. The dynamic models of the base shear coefficient and the overturning moment of RAC frame structure are developed. The dynamic models are important and can be used to evaluate the strength deterioration of RAC structure under dynamic loading.

• Journal of the Korean Society for Heat Treatment
• /
• v.31 no.1
• /
• pp.18-23
• /
• 2018

In this study, low cyclic fatigue test was carried out at room temperature condition for rolled STS304 steel. The results of this study show that rolled STS304 steel has excellent static tensile strength and fatigue characteristics. The relationship between plastic strain range and fatigue life was examined using the triangular wave in order to predict the low cycle fatigue life of rolled STS304 steel by Coffin-Manson equation. Cyclic behavior of rolled STS304 steel was characterized by cyclic hardening with increasing number of cycle through the Hysteresis loop analysis and cyclic response of maximum stress versus number of cycles. It is found that the plastic deformation energy consumed per cycle is reduced by calculating the area of the hysteresis loop.