• Proceedings of the KIPE Conference
• /
• 2013.07a
• /
• pp.317-318
• /
• 2013

State-of-Charge (SOC) is one of the most important indicators for the battery management system. Thus its precise estimation is crucial not only for effectively utilizing the energy but also preventing critical situations from happening to the powertrain of the vehicle. However, lead-acid battery is time-variant and highly nonlinear, and the hysteresis phenomenon causes large errors in estimating SOC. This paper proposes a novel SOC estimation technique for the lead-acid battery by using Extended Kalman Filter (EKF) considering hysteresis effect. The validity of the proposed technique is verified through the experiments.

• Electrical & Electronic Materials
• /
• v.9 no.10
• /
• pp.1008-1012
• /
• 1996

I-V, C-V characteristics of inverted staggered type hydrogenerated amorphous silicon thin film transistor(a-Si:H TFT) was studied and experimentally verified. The results show that the log-log plot of drain current increased by voltage increase. The saturated drain current of DC output characteristics increased at a fixed gate voltage. According to the increase of gate voltage, activation energy of electron and the increasing width of Id at high voltage were decreased. Id saturation current saturated at high Vd over 4.5V, Vg-ld hysteresis characteristic curves occurred between -15V and 15V of Vg. Hysteresis current decreased at low voltage of -15V and increased at high voltage of 15V.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.48 no.4
• /
• pp.68-76
• /
• 2011

In this paper, we propose a method for joining mobile nodes in wireless sensor networks using hysteresis features. It is possible to use static hysteresis, whereby joining and withdrawal are carried out repeatedly when a mobile node is located at boundary points. The energy consumption of the nodes can be effectively managed by a decrease in the response packets of the neighbors under the joining requests of the mobile nodes. However, static hysteresis causes a decrease in the joining rate. In order to increase the joining rate, dynamic hysteresis is used. To evaluate the performance of the proposed technique, the joining rate is investigated and analyzed. Simulation results show that the proposed method enables efficient joining according to the mobility of nodes in wireless sensor networks.

• KEPCO Journal on Electric Power and Energy
• /
• v.4 no.1
• /
• pp.9-12
• /
• 2018

The use of underground transmission power lines is expanding for the beauty and convenience of the near city. However, there is a lack of research on the losses from underground transmission power lines, especially those that support three-phase cables operating 24 hours a day. Since the supporting the cable is made of a material having a conductivity and a magnetic permeability, an eddy current and a hysteresis loss are generated due to a magnetic field caused by a current flowing in the cable. Losses occurring in this case adversely affect the power energy transfer efficiency, so research on loss is necessary. Therefore, in this paper, we analyzed the eddy currents and hysteresis losses that occur in a supporting a cable through three - dimensional finite element analysis.

• Journal of the Korean Magnetics Society
• /
• v.6 no.1
• /
• pp.1-6
• /
• 1996

To simulate the characteristics of magnetic exchange coupling at the interface of MR/TbCo thin films, the directions of magnetizations were calculated by minimizing energy in the films. Newton method and Gauss-Seidel method were used. The width of M-H curve increased with TbCo anisotropy constant, and with the thickness of the transition region of TbCo layer. Hysteresis loop width became extremely narrow (less than 10 Oe of coercivity), when the TbCo transition region length was $400\;\AA$. Also the hysteresis loop of films with low interfacial exchange coupling constant was similiar to that of short transition region length. When interfacial exchange coupling constant was 1/100 of perfect coupling, hysteresis loop showed a coercivity of less than 10 Oe. Comparing the measured hysteresis loop of a fabricated sample with that of simulated one, exchange coupling con¬stant could be estimated.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.11
• /
• pp.1887-1894
• /
• 2001

The effects of carbon black on the material properties and the fatigue life of the carbon-black filled natural rubbers were investigated. Different kinds of carbon blacks resulted in different fatigue lives, hysteresis, and critical J-values. It was noticed that the hysteresis was inversely proportional to the difference between DBPA and CTAB, and the critical J-value was almost the same regardless of the length of a precrack. In addition, different kinds of carbon blacks resulted in different fracture morphologies, and micro-scale and macro-scale roughnesses. The critical J-value was proportional to the micro-scale roughness. and it seemed relate to the size distribution of carbon black particles. By reviewing all the experimental data. it was finally noticed that the logarithmic value of the fatigue life could be linearly expressed by a multiplication of the critical J-value and the logarithmic value of the hysteresis.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.4
• /
• pp.105-110
• /
• 2014

This paper presents the hysteresis friction of a sliding elastomer on various types of surfaces. The hysteresis friction is calculated by means of an analytical model which considers the energy spent by the local deformation of the rubber due to surface asperities. By establishing the fractal character of the surfaces, the contribution to rubber friction of roughness at different length scales is accounted for. High resolution surface profilometer is used in order to calculate the main three surface descriptors and the minimal length scale that can contribute to hysteresis friction. The results show that this friction prediction can be used in order to characterize in an elegant manner the surface morphology of various surfaces and to quantify the friction coefficient of sliding rubber as a function of surface roughness, load and speed.

• Korean Journal of Materials Research
• /
• v.13 no.3
• /
• pp.144-149
• /
• 2003

This study shows an experimental investigation of a reversible nano colloidal damper, which is statically loaded. The porous matrix is composed from silica gel (labyrinth or central-cavity architecture), coated by organo-silicones substances, in order to achieve a hydrophobic surface. Water is considered as associated lyophobic liquid. Reversible colloidal damper static test rig and the measuring technique of the static hysteresis are described. Influence of the pore and particle diameters, particle architecture and length of the grafted molecule upon the reversible colloidal damper hysteresis is investigated, for distinctive types and mixtures of porous matrices. Variation of the reversible colloidal damper dissipated energy and efficiency with temperature, pressure, is illustrated. As a result, he proposed nano damper is effective one, which can be replaced the conventional damper.

• Structural Engineering and Mechanics
• /
• v.11 no.3
• /
• pp.273-286
• /
• 2001

Viscoelastic (VE) dampers have shown to be capable of providing structures with considerable additional damping to reduce the dynamic response of structures. However, the VE material appears to be sensitive to the variations in ambient temperature and vibration frequency. To minimize these effects, a new VE material has been developed. This new material shows less sensitivity to variations in vibration frequency and temperature. However, it is highly dependent on the shear strain. Experimental studies on the seismic behavior of a 2/5 scale five-story steel frame with these new VE dampers have been carried out. Test results show that the structural response can be effectively reduced due to the added stiffness and damping provided by the new type of VE dampers under both mild and strong earthquake ground motions. In addition, analytical studies have been carried out to describe the strain-dependent behavior of the VE damper. The dynamic properties and hysteresis behavior of the dampers can be simulated by a simple bilinear model based on the equivalent dissipated energy principle proposed in this study.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04b
• /
• pp.481-486
• /
• 1998

In this paper, elastic and inelastic behavior of exterior joint of moment-resisting R.C frame with non-seismic detail subjected to reversed cyclic lateral load such as earthquake excitations was investigated. 1/2-scals subassemblage exterior beam-column joint including slab was manufactured based on similitude law. Then, pseudo static test under the displacement control was performed. The results of 1)crack pattern and failure mode, 2)degradation stiffness and strength, energy dissipation capacity from load-displacement hysteresis curve, 3)strain of steel were analysed.