CoMo, NiMo/ZSM-5 catalysts were prepared at Si/Al ratios of 100, 200 and characterized by TGA, XRD and SEM. Simultaneous hydrocracking of n-heptane and hydrodesulfurization of DBT were studied over these catalysts at the ranges of temparatures between 400$^\circ$C and 500$^\circ$C, pressure of 30 $\times 10^5$ Pa and contact time of 0.02g cat. hr/ml feed in a fixed bed flow reactor. It was shown that the hydrocracking activity of n-heptane increased in the order of NM 100, CM 100, NM 200 and CM 200 catalysts. It was also shown that the Hydrodesulfurization activity of DBT increased in the order of CM 200, NM 200, CM 100 and NM 100 catalysts and these results were thought to be that the increase of acidity of catalysts might increase hydrocracking activity of these catalysts but deactive those simultaneously. In this study it was shown that CM 100 and NM 200 were active catalysts in simultaneous hydrodesulfurization of DBT and hydrocracking of n-heptane reactions.
Middle distillate was produced by the hydrocracking of F-T wax on the zeolite catalysts. Novel metal loaded zeolite catalysts had good performance for hydrocracking of F-T wax. 2 wt.% Platinum loaded H-Y zeolite catalyst showed the highest selectivity of middle distillate and conversion of F-T wax. H-Y zeolite had more strong acidity site and large pore than that of another zeolite catalyst. So, H-Y zeolilte catalyst showed the best activity for hydrocracking of F-T wax.
The hydrodesulfurization (HDS) of dibenzothiophene (DBT) were performed simultaneously over CoPtMo/LaY catalyst under high H$_{2}$ pressure. The structure and physical properties of this catalyst were characterized using XRD, IR and surface area analyzer. The origin of acid site was mainly Bronsted. The structures of impregnated molybdenum and platinum were deactivated by DBT to MoS$_{2}$ and PtS, respectively. The activities of the HDS and the hydrocracking increased with increasing temperature and pressure. They decreased with increasing the DBT mole ratio(DBT/n-heptane). They remained constant with increasing the H$_{2}$/H.C. mole ratio. With increasing pressure and DBT mole ratio, the products of secondary cracking increased. To perform simultaneous HDS and hydrocracking effectively, the optimum condition were 500.deg.C, 4MPa.
피셔트롭스반응은 합성가스 ($H_2+CO$) 로부터 액체연료를 생산하기 위한 목적으로 연구되고 있으며 최근 한정된 석유자원으로 인하여 그 중요성이 증대하고 있다. 이 반응을 통해 생산된 왁스는 수첨분해 반응을 통해 원하는 액체연료 (디젤, 항공유, 윤활유 등) 영역의 수율을 높일 수 있다. 수첨분해반응을 위해선 수소화/탈수소화 기능을 가지는 금속을 포함하고 크래킹 반응을 일으키는 산점을 가지는 양기능성 촉매가 선호된다. 본 연구에서는 수소첨가분해 반응에 이용하는 일반적인 촉매를 알아보고 왁스종류, 반응온도, 반응압력 등 공정변수에 따라 사용가능한 촉매를 조사, 비교하였다.
Fisher-Tropsch 반응을 통하여 생성되는 왁스는 황 또는 질소 성분을 포함하지 않으며 또한 방향족 및 중금속 성분이 없기 때문에 청정 수송유로써 사용이 가능하다는 장점이 있다. 그러나 Fisher-Tropsch 왁스는 그 분자량이 매우 큰 사슬형 탄화수소이기 때문에 수소첨가 분해반응을 통하여 중질유 range의 탄소수를 갖는 탄화수소로의 전환 기술이 반드시 필요하다. 이러한 수소첨가 분해반응에 사용되는 촉매는 강한 산점을 지니고 있는 양이온 교환 지르코니아가 대표적이라 할 수 있는데 최근 들어 강한 산점과 높은 산밀도, 그리고 기공의 모양과 크기에 따라 특정 반응이 제어되거나 활성화되는 형상선택성을 가지고 있기 때문에 다양한 반응에 촉매로 사용되는 제올라이트에 Pt 등의 귀금속을 담지한 촉매를 사용하여 Fisher-Tropsch 왁스의 전환율 및 중질유분의 선택도를 높이는 기술에 대한 연구가 활발히 진행되고 있다. 따라서 본 연구에서는 다양한 제올라이트 촉매에 귀금속을 담지하여 촉매를 제조하고 1L 급 고압 배치형 반응기를 이용하여 Fisher-Tropsch 왁스의 수소첨가 분해반응에 의한 중질유 제조 실험을 수행하고 그 결과를 고찰하였다.
플라스틱은 가볍고 물성이 뛰어나며 가공이 용이하면서도 낮은 가격 때문에 우리의 실생활에서 매일 사용되고 있다. 동시에 썩지 않는 특성 탓에 폐플라스틱에 의한 환경오염의 문제가 심해짐에 따라 전 세계적으로 일회용 포장재 및 용기에 사용되는 플라스틱의 사용을 금지하는 규제 및 폐플라스틱을 재활용하려는 시도가 늘어나고 있다. 하지만 인류가 지난 수십 년간 생산한 플라스틱은 약 83억 톤이지만 이중 약 10%정도만 재활용 되었을 정도로 폐플라스틱의 재활용 비율은 미비하다. 특히, 최근 코로나 팬데믹으로 인해 택배 및 배달음식 주문량이 늘어남에 따라 플라스틱의 사용량이 급증하여 폐플라스틱의 재활용 필요성은 더욱더 커지고 있다. 본 기고문에서는 불균일 촉매를 이용한 수소첨가 폐플라스틱의 분해에 관한 최신 연구동향을 다루고자 한다. 안정적이고 반응성 및 선택성이 뛰어난 촉매 개발은 폐플라스틱의 효과적인 분해를 위해서 매우 중요하다.
플라스틱은 가공과 처리가 간단하여 매년 생산량이 증가하고 있으며 이에 따라 플라스틱 폐기물의 양 또한 매년 증가하고 있다. 플라스틱 폐기물 문제를 해결하기 위하여 촉매를 활용한 업사이클링 공정은 유망한 해결책으로 제시되고 있다. 다양한 금속(Ru, Pt 등) 및 지지체(TiO2, CeO2 등)가 폴리 올레핀계 플라스틱의 화학적 재활용에 적용되었다. 입자 크기를 조절하고, 지지체의 특성 및 이종 금속을 도입하여 액체 연료의 선택도를 향상시키고 메탄 생성 양을 줄이려는 시도가 있었다. 한편으로는 값비싼 귀금속의 양을 줄임으로써 최적의 촉매를 찾기 위한 연구를 진행하였다. 본 논문에서는 이러한 hydrogenolysis 반응 및 hydrocracking 반응에서 경제성을 높이기 위하여 어떠한 시도들이 있었는지 살펴보고자 한다. 이러한 관점에서 촉매 업사이클링 공정을 통해 플라스틱 폐기물 문제를 해결할 가능성을 제시하고자 한다.
감압잔사유를 고압 회분식 반응기에 넣고, 상용 Ni-Mo/$Al_2O_3$ 촉매를 이용하여 $450^{\circ}C$, $500^{\circ}C$에서 수첨분해하였다. 그리고 반응 생성물을 단증류 혹은 GC-SIMDIS 방법으로 각각 분석하였다. 먼저 수첨분해반응에서는 두 온도 조건 모두 촉매 반응뿐만 아니라 열분해 반응도 같이 일어나고 있음을 확인하였고, 온도가 증가할수록 전환율이 증가하고, 생성물 중 가솔린 및 납사 비율이 높아졌다. 생성물 분석 결과, $500^{\circ}C$ 반응에서는 단증류와 GC-SIMDIS 분석 결과의 차이가 없었지만, $450^{\circ}C$ 반응에서는 단증류에서는 디젤이, GC-SIMDIS에서는 vacuum gas oil이 주 생성물로 드러났다. 이는 $450^{\circ}C$ 반응에서의 단증류 분석은 단증류에 의한 열분해 반응으로 인해 생성물의 선택도가 정확하지 않음을 알려준다.
This paper presents the importance of corrosion control and protection technology with a real case study of heater tube rupture damaged by High temperature H2S-H2 corrosion in the refinery. The heater was operated at the Hydrocracking unit and the operation temperature and pressure was $340^{\circ}C$ and $18kg/cm^{3}$ respectively. Top side of the convection tube was thinned by high temperature hydrogen sulfide and hydrogen gas as a uniform corrosion and finally ruptured under operation pressure. Damaged area (Convection tube zone) was blocked by protection wall, so it was impossible to inspect with conventional nondestructive examination. Instead the elbow area which is out of the protection wall was inspected regularly to evaluate the corrosion rate of convection tube indirectly. However the operation temperature and the phase of the process stream was different between inside the chamber and outside the chamber. As a result, it caused severe corrosion to the horizontal convection tube inside the chamber comparing to the elbow outside the chamber. Finally convection tube was corroded more rapidly than the elbow and ruptured after 13 years operation. Because of the rupture, the heater was totally burned and the operation was stopped for 3 months until it has been reconstructed. To prevent this kind of corrosion problem and accident, corrosion control should be strengthened and protection technology should be improved.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.