• Journal of the Korean Wood Science and Technology
• /
• v.43 no.5
• /
• pp.682-690
• /
• 2015

The bonding performance of two types of wood adhesives, namely phenol-resorcinol-formaldehyde (PRF) resin and melamine-urea-formaldehyde (MUF) resin for glued laminated timber manufactured by high frequency (HF) heating was evaluated. The HF heating system consists of HF oscillator with dielectric heating system for curing adhesives, and hydraulic press system for clamping glued laminated timber. The designed frequency and output power of the HF system was as 5 MHz and 60 kW, respectively. To verify dielectric heating mechanism under HF oscillation, the heat loss factors of laminae and adhesives were measured. The results show that it is possible to selectively heat adhesives for their curing due to the remarkably higher loss factor of the adhesives than those of wood laminae. The temperature of adhesive in the bonding line reached up to the set temperature within a few seconds by high frequency oscillating, which advanced the curing of adhesive afterwards. The bonding performance, such as shear strength of bonding line, water soaking delamination, and boiling water soaking delamination of PRF resin met the requirement of Korean Standard (KS), however the MUF resin did not meet the KS requirement of boiling water soaking delamination. These results indicate that the HF heating system is successful to manufacture glued laminated timbers with PRF resins to meet the bonding requirements.

• Journal of Ocean Engineering and Technology
• /
• v.24 no.2
• /
• pp.18-24
• /
• 2010

Submerged rubble structures include artificial reef and the mound part of the rubble mound breakwater. Artificial reef is a type of the submerged wave absorbing structure installed in a coastal zone to prevent beach erosion and designed to initially reduce the energy of incoming waves so that its run-up height and overtopping quantity can be decreased. In order to ascertain the stability of such submerged rubble structures, minimum weight of the rubble has to be calculated first from the incoming wave height using Hudson's formula or Brebner-Donnelly formula. Based on the calculated minimum weight, a model is built for use in a hydraulic model test carried out to check its stability. The foregoing two formulas used to calculate the minimum weight are empirically derived formulas based on the result of the tests on the rubble mound breakwater and it is, therefore, difficult for us to apply them directly in the calculation of the minimum weight of the submerged structures. Accordingly, this study comes up with a numerical simulation method capable of deformation analysis for rubble structures. This study also tries to identify the deformation mechanism of the submerged rubble structures using the numerical simulation. The method researched through this study will be sufficient for use for usual preparations of the design guidelines for submerged rubble structures.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.3
• /
• pp.55-61
• /
• 2011

Generally, the Box-Culvert in levee is destroyed by various reasons. Especially when Box-Culvert is installed over the pile foundation in soft ground, the failure occurrs for 1) the weakness of compaction in Box-Culvert side by the differential settlement between outer ground and inner soil prism, 2) hydraulic fracturing and disturbance of Box-Culvert side soil by the repeated acting of seepage pressure at flood time. Also the side of Box-Culvert is difficult to compact and the shear resistance is reduced by more than 1/3 for the reduction of friction caused by the difference of material property. In this study, a series of model tests are conducted for the analysis of the development mechanism of outer ground and inner soil prism by the differential settlement using the pile foundation in soft ground, and cavity suppressed technique is suggested by the analysis of base plate enlargement effect.

• Tunnel and Underground Space
• /
• v.23 no.6
• /
• pp.457-469
• /
• 2013

We have analyzed the regional in-situ stress pattern using 460 stress measurement data at about 100 test sites in Korea, and suggested correlation equations of stress-depth and stress ratio-depth. We made Korea Stress Map(KSM) as in-situ stress fields of the Korean peninsula, combining with a paleo-stress analysis according to the geological period and a stress estimation from focal mechanism. We confirmed the reliability and applicability of correlation equations derived in this study, comparing with worldwide stress-depth patterns, and also estimated the pattern of in-situ stress fields of north-eastern Asia including Korea, China and Japan, comparing with World Stress Map.

• The KSFM Journal of Fluid Machinery
• /
• v.15 no.5
• /
• pp.60-66
• /
• 2012

One of commonly physical phenomena encountered in pump sump systems in which its significant influence to the hydraulic performance of pump system plays an important role in the field of fluid engineering, is the appearance of free surface and submerged vortices. In this paper, a study of the vortices behavior and their formative mechanism of asymmetry is considered in this paper by using numerical approach. The Reynolds-Averaged Navier-Stokes (RANS) equations and k-omega Shear Stress Transport turbulence model used to describe the properties of turbulent flows, in company with VOF multiphase model, are implemented by Fluent code with multi-block structured grid system. In the numerical simulation, the calculated elevation of air-water interface and vortex core contours are used to classify visually surface vortices as well as submerged vortices. It is shown that the free surface vortex is identified by the concavity of liquid region from the free surface and swirling flow at that own plane. To investigate the distinctive behavior of these vortices corresponding to each given flow rate at the same water level, some numerical testing of them are considered here in such a manner that the flow pattern of surface vortex are obtained similarly to the obtained results from experiment. Furthermore, the influence due to the change of grid refinement and the variation of depth of the concavity are also considered in this paper. From that, these influential factors will be implemented to design a good pump sump with higher performance in the future.

• Journal of Navigation and Port Research
• /
• v.33 no.5
• /
• pp.323-330
• /
• 2009

We have been developing an underwater robot for harbour construction using a parallel mechanism The robot is attached to the rope of a crane, which curries a large stone into the undersea The robot's yaw and pitch are controlled by hydraulic cylinders but its roll is uncontrollable. We mount propellers in both side of the robot to generate the roll motion This paper studies on the control for the roll motion of a underwater robot. A gyro-sensor is used to measure the angle in a roll motion We develop the dynamic model to describe the robot's roll motion by a second order non-linear system and identify the model parameters by recursive least square and adaptive identifier. PD control, recursive model based control and adaptive model based control are applied with the dynamic model which computes the control input to compensate disturbances. This paper introduces the underwater robot system and presents the simulated and experimental results of the proposed controller.

• Journal of Korea Water Resources Association
• /
• v.39 no.11 s.172
• /
• pp.961-968
• /
• 2006

Since a small harbor is often located near surf zone areas which have great influences of sediment transport, there is a great possibility that the sediment will be deposited inside of the harbor. The sediment transport occurring around the harbor entrance can't be explained by the wind wave and wave induced current. In this study, it was investigated the mechanism of the entrainment of sediment into a small harbor with permeable breakwater using hydraulic experiments in 3D wave basin. It is found out that the significant sediment entrainment produced when the mode of oscillation in the harbor became the 1st mode. In the case where the incident wave period was shorter than the period that caused higher mode oscillation in harbor, only a little amount of sediment entrainment took place. The vortex shedding from the top of secondary breakwater played very important roll in the entrainment of sediment into the harbor. It is also found that the small jetty attached at the top of secondary breakwater could effectively prevent the entrainment of sediment into the harbor.

• The Journal of Engineering Geology
• /
• v.25 no.4
• /
• pp.623-627
• /
• 2015

To compile a flood hazard map it is essential to identify the potential risk areas. A scenario-based numerical modeling approach is commonly used to build a flood hazard map in the case of a levee-break. The model parameters that capture peak discharge, including breach formation and progress, are important in the modeling method. In this study an earth-levee-break model is constructed under the assumption that the failure mechanism and hydraulic processes are identical for all levee-break river activities. Estimation of the hydrograph at the outlet as a function of time is highlighted. The constructed hydrograph can then serve as an upper boundary condition in running the flood routing model downstream, although flood routing is not considered in this study.

• International Journal of Automotive Technology
• /
• v.8 no.2
• /
• pp.203-209
• /
• 2007

As the vehicle electronic control technology quickly grows and becomes more sophisticated, a more efficient means than the traditional in-vehicle driving test is required for the design, testing, and tuning of electronic control units (ECU). For this purpose, the hardware-in-the-loop simulation (HILS) scheme is very promising, since significant portions of actual driving test procedures can be replaced by HIL simulation. The HILS incorporates hardware components in the numerical simulation environment, and this yields results with better credibility than pure numerical simulations can offer. In this study, a HILS system has been developed for ESP (Electronic Stability Program) ECUs. The system consists of the hardware component, which that includes the hydraulic brake mechanism and an ESP ECU, the software component, which virtually implements vehicle dynamics with visualization, and the interface component, which links these two parts together. The validity of HIL simulation is largely contingent upon the accuracy of the vehicle model. To account for this, the HILS system in this research used the commercial software CarSim to generate a detailed full vehicle model, and its parameters were set by using design data, SPMD (Suspension Parameter Measurement Device) data, and data from actual vehicle tests. Using the developed HILS system, performance of a commercial ESP ECU was evaluated for a virtual vehicle under various driving conditions. This HILS system, with its reliability, will be used in various applications that include durability testing, benchmarking and comparison of commercial ECUs, and detection of fault and malfunction of ESP ECUs.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.4
• /
• pp.310-319
• /
• 2016

If a spoiler was attached to the pipeline investigated in a previous study, a strong flow and vortex at the lower part caused scouring and thus an asymmetric pressure distribution, which assisted in the analysis of the self-burial structure where a down force was applied to the pipe. However, only the fluid-pipe interaction was considered, excluding the medium (seabed), when practically burying the pipeline. Thus, this study applied a numerical model (LES-WASS-2D) to directly analyze the non-linear interactions among the fluid, pipe, and seabed in order to perform numerical simulations of a pipeline with a spoiler installed on the seabed. This allowed the self-burial mechanism of a pipeline with a spoiler to be analyzed in the same context as the previous study that considered only the fluid-pipe interaction. However, when a pipeline was installed on the seabed, a strong flow and vortex were found at the front of the bottom, and a spoiler accelerated the fluid resistances. This hydraulic phenomenon will reinforce the scouring and down force on the pipeline. In the general consideration of the numerical analysis results by the specifications and arrangements of the spoiler, a pipeline with a spoiler was found to be the most effective for the self-burial function.