• 유공압시스템학회:학술대회논문집
• /
• 유공압시스템학회 2010년도 춘계학술대회
• /
• pp.116-125
• /
• 2010

In this study, a novel hydraulic energy-regenerative system was presented from its proposal through its modeling to its control. The system was based on a closed-loop hydrostatic transmission and used a hydraulic accumulator as the energy storage system in a novel configuration to recover the kinetic energy without any reversion of the fluid flow. The displacement variation in the secondary unit was reduced, which widened the uses of several types of hydraulic pump/motors for the secondary unit. The proposed system was modeled based on its physical attributes. Simulation and experiments were performed to evaluate the validity of the employed mathematical model and the energy recovery potential of the system. The experimental results indicated that the round trip recovery efficiency varied from 22% to 59% for the test bench.

• 한국산학기술학회논문지
• /
• 제14권6호
• /
• pp.2588-2595
• /
• 2013

기존의 유압식 엘리베이터에서 엘리베이터 카의 하강행정 동안 손실 되는 유압 에너지를 회수하여 재사용하기 위하여 개발한 유압식 엘리베이터용 하이브리드 형 에너지 저감 장치에 대한 성능 특성에 관하여 연구하였다. 회수된 에너지는 축전지에 저장하여 재사용할 수 있도록 구성되어 있으며, 엘리베이터의 구동 조건에 따른 에너지 저감장치의 출력 특성, 효율 및 에너지 회수율 등에 관하여 실험을 통하여 규명하고자 하였다. 본 연구의 결과들은 하강행정 동안 버려지는 에너지의 회수율이 최대 약 54%로 에너지 저감 장치의 압력, 유량, 출력 전압과 전류, 효율 및 에너지 회수율 등과 같은 성능 특성들이 안정적이고 양호하다는 것을 보여주고 있으며, 본 연구를 통하여 유압식 엘리베이터의 에너지 저감 장치를 통하여 하강행정 동안 회수된 에너지를 재사용하데 매우 유용하며, 상용화 가능성이 충분하다는 것을 확인하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.427-428
• /
• 2013

• 유공압시스템학회논문집
• /
• 제4권1호
• /
• pp.1-6
• /
• 2007

The typical hydraulic system of hoist is composed of a hydraulic supply unit, a directional control valve, two pilot operated check valves, two flow control valves. The capacity coefficients of flow control valves should be adjusted for the hoist to operate at moderate speed and minimize the hydraulic energy loss. However, it is difficult to adjust the four capacity coefficients of flow control valves by trial and error for optimal operation. The steady state model of the hoist hydraulic system is derived and the optimal capacity coefficients of flow control valves are obtained using the complex method that is one kind of constrained direct search method.

• 유공압시스템학회논문집
• /
• 제5권1호
• /
• pp.13-19
• /
• 2008

The typical hydraulic system of hoist is composed of a hydraulic supply unit, a directional control valve, counter balance valve, and flow control valves. The flow capacity coefficients of flow control valves should be adjusted so that the hoist is operated at moderate speed and the hydraulic energy loss is minimized. However, it is difficult to adjust the flow coefficients of flow control valves by trial and error for optimal operation. Here, the steady state model of the hoist hydraulic system including the differential cylinder circuit is derived and the optimal flow capacity coefficients of flow control valves are obtained using the complex method that is one kind of constrained direct search method.

• Tribology and Lubricants
• /
• 제30권3호
• /
• pp.183-188
• /
• 2014

In this paper, we present our analysis of tribological failure examples for an anti-lock brake system(ABS) in a car. The study range of this paper is to improve the quality of ABS system by analyzing with sensor, computer, actuator and oil lines. In the first example, the brake leak from hydraulic supply line in a caliper on the rear left side of the ABS hydraulic modulator. This produces the sponge phenomenon, where the car does not brake even when the driver operates the brake pedal. The hydraulic unit operating ABS is actuator that play role regulating drive condition according with the oil pressure supplied with wheel of a car. In the second example, the service man does not completely tighten the fixed bolt after repairing the car. This causes the ABS warning lamp to light up as the ABS wheel speed sensor cannot detect whether the ABS has been activated. In the third example, the ABS electronic control unit is separated from the soldered part of the inner circuit board. Consequently, the ABS fails in control because the ABS motor pump receives no-signal for the hydraulic unit. The wheel speed sensor has to large durability because of giving signal of acting condition to computer by detected the acceleration and deceleration of wheel of a car. In the fourth example, the ABS warning lamp lights up of when cracks propagate in the circuit board soldering part. The circuit of this computer is very important part for input and output the operating signal of system. Such failures can aggravate the durability of the ABS. Thus, the ABS needs to be optimized to eliminate malfunction phenomenon.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.344-346
• /
• 2002

The pneumatic/nydraulic brake system is recently apply to the AGT system such merit as installation is convenient and brake force is strong or than pneumatic brake system. The pneumatic/ hydraulic brake system consist of brake operating unit, electronic control unit, air compressor and pneumatic/hydraulic tranducer. The components of it are controlled and designed to perform the function of brake system. Therefore, This paper design and the pnuematic/hydraulic brake system and propose the derection of development for AGT system.

• 드라이브 ㆍ 컨트롤
• /
• 제18권2호
• /
• pp.1-8
• /
• 2021

In this work, a circuit with a hydraulic power unit is formulated as a means of predicting the behavior of the prefill valve in the future. The behavior of the prefill valve can be examined by the measurements of the configured power unit, and the performance is determined by using hydraulic pumps, relief valves, and hydraulic hoses that make up the power unit. In particular, pressure/flow pulsation generated by hydraulic pumps can cause instability in the prefill valve and cause noise-induced degradation of the overall performance and reliability of the hydraulic system containing the prefill valve. Therefore, to study the behavior and performance of the prefill valve in a relatively accurate manner, the prediction of the characteristics of the hydraulic power unit driving the prefill valve is very important. In this study, the pulsation characteristics of the hydraulic pump were analyzed to theoretically demonstrate its relationship with different settings of the power unit, such as relief valve pressure settings and the presence/absence of the hose.

• Journal of Biosystems Engineering
• /
• 제17권4호
• /
• pp.396-403
• /
• 1992

In order to operate a combine harvester at the optimum conditions and maximum performance, a forward speed control system(FSCS) was designed and develped. The FSCS consisted of engine, continuously variable V-belt transmission, threshing unit, traveling unit, detecting unit, and controller. Each components of the system were mathematically modeled. By a computer simulation, the effects of control parameters such as hydraulic piston speed, speed ratio, dead band of engine speed on the system performance were analysed, and the optimum control conditions were identified. The system appeared to be the most stable at the hydraulic piston speed of 10.6mm/s and the speed ratio of 0.4. The proper dead band of engine speed appeared to be 30rpm through the simulation and verification tests.

• 수산해양기술연구
• /
• 제36권1호
• /
• pp.25-32
• /
• 2000

A combination steering system was designed to provide the flexibility in controlling the steering wheel in fishing operations of the inshore and coastal fishing vessels. The designed steering system basically is consisted of three driving units, such as a electrically driven hydraulic pump unit with a solenoid control valve, a DC motor driven hydraulic pump unit and a manually driven hydraulic pump unit, and two controllers to provide remote steering on the deck, respectively. The steering torque was measured and analyzed to investigate the dynamic performance of the developed steering system. The steering system showed excellent linearity between the working pressure of cylinder and the torque of rudder post in case of increasing in rudder angle from $5^{\circ} to 35^{\circ}$ that is, the steering torque increased from $10.4 kgf{\cdot}m$ to $105.3 kgf{\cdot}m$ and then the working pressure of cylinder fluctuated from 6.3 kgf/cm super(2) to 16.4 kgf/cm super(2). The steering time of 3.2 sec in remote hydraulic steering by the on/off solenoid valve control was much faster than 13.2 sec in the manual steering by the helmsman and 11.6 sec in the electric steering by a DC motor, and then it was verified that operation of one unit does not affect other units in combination steering system in any way. Furthermore, the developed steering system can be remotely controlled in multiple stations of the deck during the fishing operation and the automatic pilot steering unit can be used to add hydraulic steering.