• 한국전자파학회논문지
• /
• 제19권7호
• /
• pp.713-718
• /
• 2008

본 논문에서는 두 개의 $\lambda$/4 단락 스터브를 사용하여 진폭과 위상 평형 특성을 개선한 링 하이브리드(ring hybrid) 회로를 제안하였다. 제안한 회로는 기존 링 하이브리드 결합기에 존재하는 위상과 진폭 비 평형 특성을 $\lambda$/4 단락 스터브를 통해 보정한 회로이다. 제안한 링 하이브리드 결합기의 성능을 검증하기 위하여 평형 다이오드 주파수 2 체배기 회로를 설계 및 측정하였다. 실험 결과 $1.6{\sim}2.35\;GHz$의 대역 내에서 최저 12.3 dB의 변환 손실과 30 dB 이상의 기본 주파수 격리도를 보였다.

• 한국자동차공학회논문집
• /
• 제24권4호
• /
• pp.392-400
• /
• 2016

In this paper, a study based on engine operating conditions versus hybrid excavator engines was conducted about the engine performance and fuel consumption via the 1-D engine simulation model. First of all, engine operating points with performance and emission were determined by driving patterns. The 1-D HFEM(High Frequency Engine Model) was developed for deep insight into engine combustion and the energy conversion phenomena. In accordance with changing operating points, especially High Idle and Rated output conditions, engine parameters and systems such as turbocharger(Waste Gate Turbocharger and Variable Geometry Turbocharger) injection strategies and EGR(Exhaust Gas Recirculation) should be considered. Therefore, various configurations and parametric analysis with optimization methods in hybrid excavator were simulated and optimized by NLPQL(Non-linear Programming by Quadratic Lagrangian algorithm) in 1-D HFEM. As a result, the fuel consumption with the developed hybrid electric excavator engine could be significantly decreased and bsfc(Brake Specific Fuel Consumption) was also reduced about 5 % to 7 % without any performance degradation.

• 한국전기전자재료학회논문지
• /
• 제36권6호
• /
• pp.620-626
• /
• 2023

Energy harvesting technology, which converts wasted energy sources in everyday life into usable electric energy, is gaining attention as a solution to the challenges of charging and managing batteries for the driving of IoT sensors, which are one of the key technologies in the era of the fourth industrial revolution. Hybrid energy harvesting technology involves integrating two or more energy harvesting technologies to generate electric energy from multiple energy conversion mechanisms. In this study, a hybrid energy harvesting device called TMPPEG (thermo-magneto-piezoelectric-pyroelectric energy generator), which utilizes low-grade waste heat, was developed by incorporating PVDF polymer piezoelectric components and optimizing the system. The variations in piezoelectric output and thermoelectric output were examined based on the spacing of the clamps, and it was found that the device exhibited the highest energy output when the clamp spacing was 2 mm. The voltage and energy output characteristics of the TMPPEG were evaluated, demonstrating its potential as an efficient hybrid energy harvesting component that effectively harnesses low-grade waste heat.

• 적정기술학회지
• /
• 제7권1호
• /
• pp.59-71
• /
• 2021

하이브리드수열탄화 (Hybrid HTC) 기술은 2가지 이상의 유기성폐기물을 혼합한 특허 받은 열역학 공정으로 공정온도 180~250℃, 압력 20~40 bar에서 반응시간이 2시간 이내이며 에너지 소비가 적고, 폐기물의 부피감소 및 악취 저감효과가 크다. 폐기물 중 대부분의 탄소가 최종 생성물에 축적되므로 유기성 폐기물 고형연료화에 가장 적합한 기술로 평가받고 있다. 본 연구에서는 하이브리드 수열탄화기술을 활용하여 캄보디아 망고 폐기물을 대상으로 온도 및 반응시간의 변화에 따라 발열량 및 수율 등에 미치는 영향에 대하여 평가하였다. 본 연구를 통해 공정변수를 최적화하고, 전공정플랜트의 에너지 효율성을 향상시킬 수 있으며, 수연탄화기술에서 분해되어 가스가 생성되는데 이때 수소(H₂) 및 메탄(CH₄) 등 제조 및 생산기술개발을 할 수 있다. 본 연구 결과를 토대로 망고폐기물(2t/day)실증 물질수지 및 에너지 수지 도출과 함께 경제성도 평가하였다.

• 신재생에너지
• /
• 제1권1호
• /
• pp.32-36
• /
• 2005

We studied the optoelectronic properties of hybrid solar cells formed by mixing cadmium sulfide [CdS] nanorods with a conjugated polymer, poly-2-methoxy, 5-[2'-ethy[hexyloxy]-1,4-p-phenylenevinylene[MEH-PPV]. CdS nanorods were grown vertically on Ti substrates by electrochemical deposition through a porous alumina template. Absorption spectrum of the composite layer was the same as the superposition of the absorption spectrum of each individual layer. The photoluminescence signal from MEH-PPV film was reduced as a result of the mixing. The energy conversion efficiency of MEH-PPV improved from $0.0012\%$ to about $0.60\%$ when combined with the vertically aligned CdS nanorods.

• Journal of Power Electronics
• /
• 제15권6호
• /
• pp.1438-1445
• /
• 2015

A new DC-DC power converter is researched for renewable energy and battery hybrid power supplies systems in this paper. At the charging mode, a renewable energy source provides energy to charge a battery via the proposed converter. The operating principle of the proposed converter is the same as the conventional DC-DC buck converter. At the discharging mode, the battery releases its energy to the DC bus via the proposed converter. The proposed converter is a non-isolated high step-up DC-DC converter. The coupled-inductor technique is used to achieve a high step-up voltage gain by adjusting the turns ratio. Moreover, the leakage-inductor energies of the primary and secondary windings can be recycled. Thus, the conversion efficiency can be improved. Therefore, only one power converter is utilized at the charging or discharging modes. Finally, a prototype circuit is implemented to verify the performance of the proposed converter.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제4B권2호
• /
• pp.80-85
• /
• 2004

This paper reports the performance of a CB (Circuit Breaker) and converter for the battery operated Wind-PV (Photovoltaic) system. For this purpose, a fluctuating reduction controller for an electric generation hybrid (wind+PV) system is suggested. The method operates a wind turbine, PV, CB, converter and battery. Integration of wind and PV sources, which are generally complementary, usually reduce the capacity of the battery. Also, CB controls the overvoltage of the generation system. The objective is to control the operation of the converter and the CB and reduce power fluctuation. This paper includes discussion on system performance, power quality, fluctuation and effect of the randomness of the wind.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.1334-1339
• /
• 2004

This paper proposes transformerless power conversion system consisting of a single-phase diode rectifier and a shunt hybrid filter for the electric-railway system. The hybrid filter consists of a single tuned LC filter per a phase and a low-rated NPC type multi-level inverter. Compared with conventional active filters. Transformers are not used. Also, LC filter works as not only a harmonic filter tuned at the 5th harmonic frequency but also a switching-ripple filter. The rating of the active filter can be decreased by using a NPC type multi-level inverter. The simulation results confirm the validity of the system.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.1427-1432
• /
• 2004

This paper proposes transformerless power conversion system consisting of a single-phase diode rectifier and a shunt hybrid filter for the electric-railway system. The hybrid filter consists of a single tuned LC filter per a phase and a low-rated NPC type multi-level inverter. Compared with conventional active filters. Transformers are not used. Also, LC filter works as not only a harmonic filter tuned at the 5th harmonic frequency but also a switching-ripple filter. The rating of the active filter can be decreased by using a NPC type multi-level inverter. The simulation results confirm the validity of the system

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.328-334
• /
• 2000

The hybrid catalytic(catalytic+thermal) combustor of a lean methane-air mixture on platinum catalyst was investigated numerically using a 2-D boundary layer model with detailed homogeneous and heterogeneous chemistries. For the more accurate calculations, the actual surface site density of monolith coated with platinum was decided by the comparison with experimental data. It was found that the homogeneous reactions in the monolith had little effect on the change of temperature profile, methane conversion rate and light off location. However, the radicals such as OH and CO were produced rapidly at exit by homogeneous reactions. Thus the homogeneous reactions were important to predict the productions of CO and NOx exactly. In thermal combustor, the production of $N_2O$ was more dominant than that of NO due to the relative important of the reaction $N_2+O(+M){\to}N_2O(+M)$. Finally the production of CO and NOx by amount of methane addition were studied.