• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.20-24
• /
• 2003

The feasibility of hybrid motor as a first stage of the air launch vehicle is investigated, and the result shows the hybrid motor can replace the solid motor. Optimal design study has been performed for the hybrid motor as a first stage of nanosat air launch vehicle. The first stage hybrid motor of the nanosat air launch vehicle, which uses the F-4E Phantom as a mother plane is designed for given mission requirements. Selected design variables are the number of ports, the initial oxidizer flux, the combustion chamber pressure, and the nozzle expansion ratio. The design results show that a hybrid motor can be successfully applicable to very small air launch vehicles which have severe physical constraints of length and diameter imposed by the mother plane.

• Journal of Power Electronics
• /
• v.9 no.6
• /
• pp.960-968
• /
• 2009

This paper presents a design optimization process for interior permanent magnet synchronous motors (IPMSM) for hybrid electric compressors (HEC) which are applied to hybrid electrical vehicles. A hybrid electric compressor is composed of an electric motor driving section and an engine driving section which is connected to the engine by a pulley belt. A hybrid electric compressor driving motor requires half of the full driving power of a compressor. Even though an engine is not operated at the idling stop mode, the electric motor drives the air-conditioner compressor by itself so that the air conditioning system can produce its minimum cooling capacity. In this paper, the design optimization of an IPMSM for a 42 (V) applied voltage system is studied using the design of experiment (DOE) and response surface method (RSM) of 6sigma. The driving characteristics of this motor drive system are measured and analyzed by experiment.

• Proceedings of the KIEE Conference
• /
• 1991.11a
• /
• pp.126-129
• /
• 1991

The effect of each tooth for optimal design of Hybrid permanent magnet step motor is presented on this paper. For this consideration, Hybrid permanent magnet step motor was designed in the first consideration tooth structure on the stator and the rotor and poles structure, as number of teeth on the stator and the rotor and slot depth and pitch of teeth, simulated by AutoLISP. During actual rotating, a chracteristic of Hybrid permanent magnet step motor which designed by AutoLISP program is considered. A chracteristic of Hybrid permanent magnet step motor is considered in change each variable, also. As a result, it was found that characteristic of Hybrid permanent magnet step motor changed in accordance with tooth structure and number of teeth and optimal design is possible by AutoLISP.

• Journal of Power Electronics
• /
• v.4 no.3
• /
• pp.127-137
• /
• 2004

This paper introduces a hybrid induction motor control using a genetically optimized pseudo-on-line method. Optimization results from the use of a look-up table based on genetic algorithms to find the global optimum of an unconstrained optimization problem. The approach to induction motor control includes a pseudo-on-line procedure that optimally estimates parameters of a fuzzy PID (FPID) controller. The proposed hybrid genetic fuzzy PID (GFPID) controller is applied to speed control of a 3-phase induction motor and its computer simulation is carried out. Simulation results show that the proposed controller performs better than conventional FPID and PID controllers. The contribution of this paper is the introduction of a high performance hybrid form of induction motor control that makes on-line and real-time control of the drive system possible.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.11 no.8
• /
• pp.338-348
• /
• 2001

A hybrid self-hearing motor, which Is a functional combination of general permanent magnet (PM) motor and hybrid active magnetic bearing(AMB), was proposed a few years ago. In this paper the hybrid self-bearing motor is modified to a disk type, in which one of two magnetic hearings was substituted for a thin yoke to make the system more compact. An outer rotors in this self-hearing motor is actively controlled only in two radial directions while the ocher motions are passively salable owing to the disk-type structure. Main advantages of the proposed self-hearing motor are simple control mechanism, low power consumption and smart structure. Mathematical model for the magnetic force Is built wish consideration of the radial displacement of the rotor. The model helps us not only to design a levitation controller but also to expect the system performance. Some experimental results show good capability and feasibility of the Proposed self-bearing motor.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10b
• /
• pp.566-569
• /
• 1987

The primary difficulties encountered in the use of step motors are underdamped response when stopping at a specified position and dynamic instability during high-speed slewing. This paper proposes a speed and position detection scheme using the back EMF generated by the rotating permanent magnet field of a two-phase 1.8.deg. hybrid step motor, and presents its application to the state-variable feedback control of the hybrid step motor. All simulation results in a single step response show that the hybrid step motor performances such as peak overshoot and settling time are greatly improved.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1075-1076
• /
• 2007

The HEV (Hybrid Electrical Vehicle) becomes commercialized recently because of high fuel efficiency and low air pollution. The highest output power system except the traction motor is an air conditioner compressor in HEV system. The full or hybrid electric compressor is applied for HEV. The general HEC (Hybrid Electric Compressor) requires the half power motor and drive system of the full electric compressor because the rated output power of motor drive system is designed to charge the minimum cooling capacity at the time of idle stop. Therefore, this hybrid electric is more economical and practical solution. In this paper, we studied about the motor drive system of hybrid electric compressor for HEV. The applied voltage specification is 42 V, an IPMSM (Interior Permanent Magnet Synchronous Motor) is designed and applied as the compressor drive motor.

• 제어로봇시스템학회:학술대회논문집
• /
• 1986.10a
• /
• pp.377-382
• /
• 1986

This paper describes the modelling method of hybrid step motors including magnetic saturation effects of iron parts and the simulation for design of a prototype. Based on the above procedure, the prototype of a step motor is produced and its characteristics are discussed.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.11B no.2
• /
• pp.15-21
• /
• 2001

This paper presents an improved characteristic analysis methodology for a 5-phase hybrid stepping motor. The basic approach is based on the use of equivalent magnetic circuit taking into account the localized saturation throughout the hybrid stepping motor. The finite element method(FEM) is used to generate the magnetic circuit parameters for the complex stator and rotor teeth and airgap considering the saturation effects in tooth and poles. In addition, the neural network is used to map a change of parameters and predicts their approximation. Therefore, the proposed method efficiently improves the accuracy of analysis by using the parameter characterizing localized saturation effects and reduces the computational time by using the neural network. An improved circuit model of 5-phase hybrid stepping motor is presented and its application is provided to demonstrate the effectiveness of the proposed method.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.3
• /
• pp.72-78
• /
• 2003

In this paper, the feasibility study and the parametric design of hybrid motor with HTPB/LOX were conducted for micro air launch system. Design results were compared with 1st stage of Pegasus XL for verification of hybrid motor. Results showed that hybrid motor replace solid booster if Isp of hybrid motor reaches 330sec. In addition, mission analysis was established for micro air launch system, and parametric design was conducted with design variables: number of port, initial oxidizer flux, and chamber pressure. And the region of Isp was identified by parametric study which satisfied design constraints and mission analysis.