• 에너지공학
• /
• 제14권4호
• /
• pp.213-218
• /
• 2005

습공기 유동의 착상조건하에서의 열 및 물질 전달 특성을 이해하기 위해서, 미니 열풍동을 제작하고 열풍동의 시험부인 사각덕트 아랫면에 알루미늄 평판을 설치하고 평판의 중심력에 전기냉각모듈(Peltier device)을 부착하였다. 현미경(해상도 0.05mm)을 이용하여 습공기 유동 방향으로 알미늄 평판위의 7개점의 서리 두께를 측정하였으며, 전자저울(해상도 1mg)을 이용하여 각 운전시간대까지의 발생된 서리의 총괄 질량을 측정하였다. 여러 가지의 실험조건에서 서리두께와 서리질량 그리고 알미늄 평판상의 온도 분포 등을 구하고, 이로부터 습공기 유동의 습도 및 속도가 서리의 성장 특성에 미치는 영향을 분석하였다.

• 에너지공학
• /
• 제17권1호
• /
• pp.1-7
• /
• 2008

본 연구는 착상이 일어나는 조건에서 작은 사각 덕트내의 습공기의 층류유동에서 열 및 물질전달특성을 이해하고자 수행되었다. 알루미늄 평판이 열교환기의 핀부분을 모사하기 위하여 사용되었다. 알루미늄 표면온도는 착상조건에서의 열 및 물질전달 특성을 조사하여 해석하기 위하여 측정되었다. 또한 열교환기 공기측 채널에서 착상에 의한 air-blocking효과를 화인하기 위해 압력강하가 측정되었다. 그리고 착상조건에서 습공기의 국소 특성을 해석하기 위한 방법이 제시되었다.

• 설비공학논문집
• /
• 제14권6호
• /
• pp.519-524
• /
• 2002

An experimental study has been conducted to investigate the effects of surface energy on frost formation. Test samples with two different surfaces are installed in a wind tunnel and exposed to a humid airflow. Dynamic contact angles (DCA) for these surfaces are $23^{\circ}\;and\;88^{\circ}$, respectively. The thickness and the mass of frost layer are measured and used to calculate the frost density while frost formation is visualized simultaneously with their measurements. Results show that frost density increases as time increases at specific test conditions. The air Reynolds number, the airflow humidity and the cold plate temperature are maintained at 12,000, 0.0042 kg/kg and $-21^{\circ}C$, respectively. The surface with a lower DCA shows a higher frost density during two-hour test, but no differences in the frost density have been found after two hours of frost generation. Empirical correlations for thickness, mass and density are assumed to be the functions of the test time and DCA.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2004년도 동계학술대회 논문집
• /
• pp.37-37
• /
• 2004

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2004년도 동계학술대회 논문집
• /
• pp.38-38
• /
• 2004

• 설비공학논문집
• /
• 제20권5호
• /
• pp.334-341
• /
• 2008

The purpose of this study is to investigate the effects of changing air temperature and the changing on/off periods of the air-conditioner system. Adding to that, this paper discuss is to consider the effects of air temperature with the air-conditioner system upon the human thermal comfort. The experiment is conducted during the summer. The subjects(6 young females) are exposed to the following conditions: combinations of 2 Swing and 2 Linear air control Conditions. (2 Swing during 40 min, 4 Swing during 40 min, Linear 40 min, Linear 60 min in still air and RH 50%). From the experiment, the following results are obtained; the thermal sensation vote is neutral after 90 minute. The mean skin temperature ranged about $34^{\circ}C$ at all conditions. The skin temperature was greatly affected by 2 Swing big amplitude condition.

• Carbon letters
• /
• 제8권4호
• /
• pp.280-284
• /
• 2007

Samples of active carbon of $1150\;m^2/g$ surface area were impregnated with ammoniacal salts of copper, chromium and silver, with and without triethylenediamine. The samples of impregnated carbon were aged at $50^{\circ}C$, with and without 90% RH (relative humidity), for a little more than one year and chemically evaluated periodically. Initially copper (II) and chromium (VI) reduced very fast in the samples in humid atmosphere to the extent of 30% and 60% respectively in four months. These values were found to be unaffected by the presence of triethylenediamine (TEDA) indicating that the chemical did not retard the reduction process of chromium (VI) and copper (II). However, in the absence of humidity the reduction of the impregnants was significantly less (10-12%, w/w) in four months. It was quite evident; therefore, that the moisture was mainly responsible for the reduction of chromium (VI) and copper (II) species in impregnated carbons. The prolonged ageing of the samples with and without triethylenediamme after four months with and without humid atmosphere showed that the extent of reduction of chromium (VI) was very low, i.e. 5-10% and of copper (II) was 2-25%. Silver is not reduced due to carbon, as it remained unchanged in concentration on storage. The impregnated carbon samples (100 g) without triethylenediamine, which were aged at room temperature for 5 years in absence of humidity and unaged when evaluated against cyanogen chloride (CNCl) at a concentration of 4 mg/L and airflow rate of 30 lpm showed a high degree of protection (80- 110 minutes).

• Safety and Health at Work
• /
• 제14권4호
• /
• pp.457-466
• /
• 2023

Background: During hot environment work tasks with whole-body enclosed anti-bioaerosol suit, the combined effect of heavy sweating and exhaled hot humid air may cause the N95 medical respirator to saturate with water/sweat (i.e., water-blocking). Methods: 32 young male subjects with different body mass indexes (BMI) in whole-body protection (N95 medical respirator + one-piece protective suit + head covering + protective face screen + gloves + shoe covers) were asked to simulate waste collecting from each isolated room in a seven-story building at 27-28℃, and the weight, inhalation resistance (R_f), and aerosol penetration of the respirator before worn and after water-blocking were analyzed. Results: All subjects reported water-blocking asphyxia of the N95 respirators within 36-67 min of the task. When water-blocking occurred, the R_f and 10-200 nm total aerosol penetration (P_t) of the respirators reached up to 1270-1810 Pa and 17.3-23.3%, respectively, which were 10 and 8 times of that before wearing. The most penetration particle size of the respirators increased from 49-65 nm before worn to 115-154 nm under water-blocking condition, and the corresponding maximum size-dependent aerosol penetration increased from 2.5-3.5% to 20-27%. With the increase of BMI, the water-blocking occurrence time firstly increased then reduced, while the R_f, P_t, and absorbed water all increased significantly. Conclusions: This study reveals respirator water-blocking and its serious negative impacts on respiratory protection. When performing moderate-to-high-load tasks with whole-body protection in a hot environment, it is recommended that respirator be replaced with a new one at least every hour to avoid water-blocking asphyxia.