• 대한전자공학회논문지
• /
• 제27권5호
• /
• pp.737-746
• /
• 1990

Ga0.47In0.53As PIN photodiodes(PD) having various areas have been fabricated by liquid phase epitaxial techniques. Ternary melt has been baked out at 675\ulcorner in H2 atmosphere for 20 hours before growth, which resulted in reduction of background carrier concentration of grown epi-layer. Also, lattice mismatch has been controlled within 0.01%. The room temperature performance of 10**-4cm\ulcornerarea PIN PD at a bias voltage of -5V were` quantum efficiency(with no antireflection coating)=60% for 1.3\ulcorner light source, dark current\ulcorner5nA, and capacitance\ulcornerpE. Frequency response measurement of packaged PIN PD has shown that cut-off frequency (f-3dB) was 961MHz. This PD has shown a good eye pattern when it was incorporated in a 565Mbps optical receiver.

• Journal of Mechanical Science and Technology
• /
• 제18권1호
• /
• pp.12-19
• /
• 2004

Using LSM (laser scanning method) , the radius of curvature due to thermal deformation in polyimide film coated on Si substrate is measured. Since the polyimide film shows viscoelastic behavior, i.e., the modulus and deformation of the film vary with time and temperature, we estimate the relaxation modulus and the residual stresses of the polyimide film by measuring the radius of curvature and subsequently by performing viscoelastic analysis. The residual stresses relax by an amount of 10％ at 100$^{\circ}C$ and 20% at 150$^{\circ}C$ for two hours.

• 한국산업보건학회지
• /
• 제24권4호
• /
• pp.536-546
• /
• 2014

Objectives: The major objective of this paper is compare the exposure work hours and experieence of ill health symptoms among under and over employment and matched group. Workers with over employment have more exposed to hazards than that with under employment because that workers with over employment work more than those with ender employment. Methods: This study as heuristics one used the third Korean Working Conditions Survey done by Occupational Safety and Health Research Institute in 2011. The sample size is 50,023 economic active persons. Over and under employment were measured by matching method of preferred and actual work hours. The exposed work hours to hazards were measured according to 13 hazardous factors and the experience of ill health symptoms were scaled by the number of experienced 14 ill health symptoms. To compare the exposure and the symptoms experience were compared by mean difference test with F test. Results: The proportion of over employment in male employees is 32.1% and that in female employees is 29.3% and under employment rate is 11.2% in mae and 13.9% in female employees. There is significant difference of the rate of over and under emplyment among age groups, industrial sectors, occupational groups and the state of employment. The difference of the exposed work hours to hazards among under, over and matched group were statistically significant in all hazards by gender. The exposed work hours to hazards in over employment were more than those in under employment. The number of experienced symptoms in over employment is statistically significantly more than that in under employment. Conclusions: Workers with over employment may be vulnerable group in the criteria of hazard exposure and health status. The results have some implications and limitations because that this study is heuristic one. The mismatch of preferred and actual working hours may be unfavorable work condition that has impact on safety and health of workers. The impact mechanism may be investigated as future study, Because that this study used cross sectional survey data, some causal relationships cannot be evaluated.

• 산업노동연구
• /
• 제24권3호
• /
• pp.35-71
• /
• 2018

본 논문은 몸이 아픈데도 불구하고 출근을 하는 행위를 뜻하는 프리젠티즘(presenteeism) 과 연관되어 있는 직업 환경적 요소들을 탐색하고자 하는데 목적이 있다. 프리젠티즘은 학술연구 분야에서 상대적으로 새로운 개념이지만, 노동자들의 미래의 직업적 전망과 삶의 질에 위협을 가하는 중요한 요인이자, 노동생산성을 저하시킨다는 의미에서 중요한 사회적 이슈가 된다. 이 연구를 위해 안전보건공단에서 실시하는 근로환경조사 2014년 자료가 사용되었고, 분석에는 15세 이상의 임금근로자 24,571 명이 포함되었다. 프리젠티즘의 경험 여부에 대한 로지스틱 분석을 시행하여 노동시간과 개인생활, 노동환경과 직장환경, 고용불안정, 보상과 복지 네 가지 측면에서의 가설을 검증하였다. 분석 결과로부터 1) 근무시간으로 인해 가족/사회생활의 어려움이 크다고 느낄수록, 2) 노동시간압박이 크고, 직장만족도가 낮을수록, 3) 직업불안정성이 클수록, 4) 복지 수준이 낮을수록 프리젠티즘의 가능성이 높다는 점이 확인되었다. 이는 직장의 업무요구나 직업적 환경이 개인의 주관적 기대수준과 부조화가 나타나 개인적 자원의 손실이 예상될 경우, 건강상태가 좋지 않음에도 불구하고 출근을 하여 그 손실을 메우고자 한다는 본 논문의 이론적 논의와 일관된 결과라 볼 수 있다. 프리젠티즘은 노동자 개인의 삶의 질과 건강에 부정적인 영향을 줄 뿐만 아니라 사회적 비용도 발생시키는 관행인 만큼, 조직적인 측면에서 이를 예방할 수 있는 방법에 대한 모색이 필요하다.

• 대한치과보철학회지
• /
• 제35권1호
• /
• pp.221-243
• /
• 1997

The objective of this study was to characterize the mechanical properties of $Y_{2}O_{3}$-containing glass infiltrated ceramic core material, which was made by pressureless powder packing method. A pure alumina powder with a grain size of about $4{\mu}m$ was packed without pressure is silicon mold to form a bar shaped sample, and applied PVA solution as a binder. Samples were sinterd at $1350^{\circ}C$ for 1 hour. After cooling, $Y_{2}O_{3}$-containing glass($SiO_{2},\;Y_{2}O_{3},\;B_{2}O_{3},\;Al_{2}O_{3}$, ect) was infiltrated to the sinterd samples at $1300^{\circ}C$ for 2 hours and cooled. Six different proportions $Y_{2}O_{3}$ of were used to know the effect of the mismatch of the thermal expansion coefficient between alumina powder and glass. The samples were ground to $3{\times}3{\times}30$ mm size and polished with $1{\mu}m$ diamond paste. Flexural strength, fracture toughness, hardness and other physical properties were obtained, and the fractured surface was examined with SEM and EPMA. Ten samples of each group were tested and compared with In-Ceram(tm) core materials of same size made in dental laboratory. The results were as follows : 1. The flexural strengths of group 1 and 3 were significantly not different with that of In-Ceram, but other experimental groups were lower than In-Ceram. 2. The shrinkage rate of samples was 0.42% after first firing, and 0.45% after glass infiltration. Total shrinkage rate was 0.87%. 3. After first firing, porosity rate of experimental groups was 50%, compared with 22.25% of In-Ceram. After glass infiltration, porosity rate of experimental groups was 2%, and 1% in In-Ceram. 4. There was no statistical difference in hardness between two materials tested, but in fracture toughness, group 2 and 3 were higher than In-Ceram. 5. The thermal expansion coefficients of experimental groups were varied to $4.51-5.35{\times}10^{-6}/^{\circ}C$ according to glass composition, also the flexural strengths of samples were varied. 6. In a view of SEM, many microparticles about $0.5{\mu}m$ diameter and $4{\mu}m$ diameter were observed in In-Ceram. But in experimental group, the size of most particles was about $4{\mu}m$, and a little microparticles was observed. The results obtained in this study showed that the mismatch of the thermal expansion coefficients between alumina powder and infiltrated glass affect the flexural strength of alumin/glass composite. The $Y_{2}O_{3}$-containing glass infiltrated ceramic core made by powder packing method will takes less time and cost with sufficient flexural strength similar to all ceramic crown made with slip casting technique.

• Animal Bioscience
• /
• 제35권1호
• /
• pp.126-137
• /
• 2022

Objective: Efficient gene editing technology is critical for successful knock-in in domestic animals. RAD51 recombinase (RAD51) gene plays an important role in strand invasion during homologous recombination (HR) in mammals, and is regulated by checkpoint kinase 1 (CHK1) and CHK2 genes, which are upstream elements of RAD51 recombinase (RAD51). In addition, mismatch repair (MMR) system is inextricably linked to HR-related pathways and regulates HR via heteroduplex rejection. Thus, the aim of this study was to investigate whether clustered regularly interspaced short palindromic repeats/CRISPR-associated 9 (CRISPR/Cas9)-mediated knock-in efficiency of human lactoferrin (hLF) knock-in vector in the bovine β-casein gene locus can be increased by suppressing DNA MMR-related genes (MSH2, MSH3, MSH6, MLH1, and PMS2) and overexpressing DNA double-strand break (DSB) repair-related genes (RAD51, CHK1, CHK2). Methods: Bovine mammary epithelial (MAC-T) cells were transfected with a knock-in vector, RAD51, CHK1, or CHK2 overexpression vector and CRISPR/sgRNA expression vector to target the bovine β-casein gene locus, followed by treatment of the cells with CdCl₂ for 24 hours. After 3 days of CdCl₂ treatment, the knock-in efficiency was confirmed by polymerase chain reaction (PCR). The mRNA expression levels of DNA MMR-related and DNA DSB repair-related genes were assessed by quantitative real-time PCR (RT-qPCR). Results: Treatment with CdCl₂ decreased the mRNA expression of RAD51 and MMRrelated genes but did not increase the knock-in efficiency in MAC-T cells. Also, the overexpression of DNA DSB repair-related genes in MAC-T cells did not significantly affect the mRNA expression of MMR-related genes and failed to increase the knock-in efficiency. Conclusion: Treatment with CdCl₂ inhibited the mRNA levels of RAD51 and DNA MMR-related genes in MAC-T cells. However, the function of MMR pathway in relation to HR may differ in various cell types or species.

• Applied Microscopy
• /
• 제25권2호
• /
• pp.73-79
• /
• 1995

The oxidation of silicon wafers is an essential step in the fabrication of semiconductor devices. It is known to induce degradation of electrical properties and lattice strain of Si substrate from thermal oxidation process due to charged interface and thermal expansion mismatch from thermally grown SiO, film. In this study, convergent beam electron diffraction technique is employed to directly measure the lattice strains in Si(100) and $4^{\circ}$ - off Si(100) substrates with thermally grown oxide layer at $1200^{\circ}C$ for three hours. The ratios of {773}-{973}/{773}-{953} Higher Order Laue Zone lines were used at [012] zone axis orientation. Lattice parameters of the Si substrate as a function of distance from the interface were determined from the computer simulation of diffraction patterns. Correction value for the accelerating voltage was 0.2kV for the kinematic simulation of the [012]. HOLZ patterns. The change in the lattice strain profile before and after removal of oxide films revealed the magnitudes of intrinsic strain and thermal strain components. It was shown that $4^{\circ}$ -off Si(100) had much lower intrinsic strain as surface steps provide effective sinks for the free Si atoms produced during thermal oxidation. Thermal strain in the Si substrate was in compression very close to the interface and high concentration of Si interstitials appeared to modify the thermal expansion coefficient of Si.

• 한국방사선학회논문지
• /
• 제15권5호
• /
• pp.591-602
• /
• 2021

급성 허혈성 뇌졸중(Acute ischemic stroke; AIS) 환자는 증상발현 수 시간 이내 영상의학 검사를 통해 뇌경색(Infarction)을 조기 진단하여야 한다. 본 연구에서 SVD와 Bayesian 알고리즘을 이용한 뇌경색의 부피측정을 관류 전산화단층촬영(Computed tomography perfusion; CTP)과 확산 강조 자기공명영상(Magnetic resonance diffusion weighted image; MR DWI)을 비교하여 임상적 유용성을 알고자 하였다. 2017년 9월부터 2020년 9월까지 급성 허혈성 뇌졸중 증상으로 응급실을 내원한 환자 중 50명(남 : 여 = 33 : 17)의 영상의학 검사 정보를 후향적으로 이용하였다. SVD와 Bayesian 알고리즘으로 측정된 뇌경색 부피는 윌콕슨 부호순위검정(Wilcoxon signed rank test) 통계분석을 하여 중앙값(Median)과 사분위수(Iter quartile range; IQR) 25 - 75% 범위로 나타내었다. CTP 검사로 측정한 core volume(단위 : cc)은 SVD가 18.07 (7.76 - 33.98), Bayesian은 47.3 (23.76 - 79.11)으로 측정되었고 penumbra volume은 SVD가 140.24 (117.8 - 176.89), Bayesian은 105.05 (72.52 - 141.98)로 측정되었다. Mismatch ratio (%)는 SVD가 7.56 (4.36 - 15.26), Bayesian은 2.08 (1.68 - 2.77)로 측정되었으며 모든 측정값은 통계적으로 유의미한 차이가 있었다(p < 0.05). 스피어만 상관 분석(Spearman's correlation analysis) 결과는 CT Bayesian과 MR로 측정한 뇌경색 부피의 상관계수(r = 0.915)가 CT SVD와 MR의 상관계수(r = 0.763)보다 더욱 높은 양의 상관관계를 보였다(p < 0.01). 블랜드 알트만 산점도(Bland altman plot) 분석 결과는 CT Bayesian과 MR로 측정한 뇌경색 부피의 산점도 기울기(y = - 0.065)가 CT SVD와 MR의 산점도 기울기(y = - 0.749)보다 완만하게 측정되어 Bayesian이 더 높은 신뢰성을 나타내었다. 따라서 뇌경색 부피의 측정에서 Bayesian 알고리즘이 SVD보다 높은 정확도를 보였으므로 임상에서 유용하게 사용될 것으로 사료된다.

• 대한핵의학회지
• /
• 제27권2호
• /
• pp.155-160
• /
• 1993

심근생존능은 심기능이 저하되어 있으나 적절한 치료에 의해 심기능이 회복될 수 있는 상태를 말하며, 기절심근과 동면심근으로 대변할 수 있다. 기절심근은 심근관류가 정상이지만 아직 심근기능이 회복이 안된 상태로 수 시간 내지 수주일 후에 회복이 되는 상태를 말하며, 동면심근은 심근관류가 오랫동안 감소되어 있어 심기능 저하되어 있지만 심근관류를 정상화시켜주면 바른 시간내에 심기능이 회복되는 상태를 말한다. 임상적으로는 이 두가지 상태가 혼합된 경우도 있으리라 추측되고 있다. 심근생존능을 진단하는 것은 재혈관화 치료를 시행하기 전에 미리 환자의 예후를 결정해 줄 수 있다는 점에서 임상적인 의의가 있다. 그 진단법으로는 PET에 의해 심근대사기능이 존재함을 증명하는 것이 표준으로 되어 있으나, 그 외에도 심장초음파, 심장 MRI등을 이용한 검사법, $^{201}TI$ 또는 $^{99m}Tc-MIBI$를 이용한 신티그라피등의 검사법이 있다. 현재까지 보고된 바를 종합하면 $^{201}TI$ 부하-재분포-재주사영상법이 가장 우수한 것으로 사료되나, 각 진단법이 개선 또는 개발되고 있으므로 이에 대한 계속적인 관심이 필요하며, 핵의학적인 진단방법도 계속적으로 발전시킬 필요가 있다고 사료된다.