• Journal of Biosystems Engineering
• /
• 제35권5호
• /
• pp.350-356
• /
• 2010

The fans installed in standard Hanwoo loose barns (room size : 10 m (width) $\times$ 5 m (length)) are frequently used to reduce Hanwoo's heat stress during hot weather and to dry the wet floor. However, the most effective method of installing fans has not been suggested yet. Therefore, this study was carried out to evaluate two methods of installing fans under the ceiling of Hanwoo loose barn by using CFD (Computational Fluid Dynamics) code, FLUENT and to recommend the optimum fan installing method. The fan installation options were fan tilting angles of $45^{\circ}$ and $0^{\circ}$ (horizontal). The fans of 1 m diameter were installed at 3 m above floor. A velocity scale on 10 cm and 110 cm above floor and air flow pattern were used as the parameters to evaluate the fan installing methods. The fans tilted at $45^{\circ}$ angle produced higher wind at 10 cm and 110 cm above floor and more uniform air flow pattern, compared with the fans installed horizontally. Based on these results, fans tilted at $45^{\circ}$ angle may help to reduce Hanwoo's heat stress and will dry the floor better than fans installed horizontally. Therefore, it is suggested that the fans of 1 m diameter in a standard Hanwoo loose barn should be installed at a $45^{\circ}$ tilt angle and 3 m above floor with spacing of 5 m at the center of a room column.

• 설비공학논문집
• /
• 제8권1호
• /
• pp.1-12
• /
• 1996

In lots of application to heat exchanger systems, closed two-phase thermosyphons are tilted from a horizontal. If the tilt angle, especially, is less than 30$^{\circ}$, the operational performances of thermosyphon are highly dependent on tilt angle. The present study was conducted to better understand such operational behaviors as mech-anni는 of phase change, and flow patterns inside a tilted thermosyphon. For experiment, an ethanol thermosyphon with a 35% of fill charge rate was designed and manufactured, using a copper tube with a diameter 19mm and a length 1500mm. Through a series of test, the tilt angle was kept constant at each of 4 different values in the range 10~25deg. and the heat supply to the evaporator was stepwisely increased up to 30㎾/$m^2$. When a steady state was established to the thermosyphon for each step of thermal loads, the wall temperature distribution and vapor temperature at the condenser were measured. The wall temperature distributions demonstrated a formation of dry patch in the top end zone of the evaporator, with a values of temperature 20~4$0^{\circ}C$ higher than the wetted surface for a moderate heat flux q≒20㎾/$m^2$. Inspite of the presence of hot dry patch, however, the mean values of boiling heat transfer coefficient at the evaporator wall were still in a good agreement with those predicted by Rohsenow's formula, which was based on nucleate boiling. For the condenser, the wall temperatures were practically uniform, and the measured values of condensation heat transfer coefficient were 1.7 times higher than the predicted values obtained from Nusselt's film condensation theory on tilted plate. Using those two expressions, a correlation was formulated as a function of heat flux and tilt angle, to determine the total thermal resistance of a tilted thermosyphon. The correlation formula showed a good agreement with the experimental data within 20%.

• 동력기계공학회지
• /
• 제9권4호
• /
• pp.51-57
• /
• 2005

In order to prevent the environmental pollution, the dryers are commonly used to treat sludge that one of sewages is polluting the quality of water. Generally, the drying method is various as to the property of material and use. Rotary dryer is a good apparatus to treat them. The rotary dryer is the way that is to make substance transmission and heating using hot air between sludge particles and heated gas. In this paper, we performed a numerical analysis of the inner air flow of the 3-pass rotary dryer through the changing rotational speed from 3rpm to 10rpm. In this result, we found that 3rpm is effective to dry material in terms of heat transfer because large scale velocity fluctuation is occurred inside the first and second drum. Also we confirmed that 5rpm and 8rpm showed up uniform flow at the center area of the first drum.

• 한국식품과학회지
• /
• 제31권3호
• /
• pp.625-630
• /
• 1999

효소식품인 현미코오지를 제조한 후 마이크로파 진공건조를 적용하여 건조하고 그 건조특성과 효소활성을 열풍건조, 진공건조, 또는 동결건조의 경우와 비교해 보았다. 마이크로파 진공건조의 경우 열전달속도가 빨라 건조 시작후 $5{\sim}10$분만에 $40^{\circ}C$에 도달한 후 건조시간 내내 $40{\pm}2^{\circ}C$를 유지하였다. 열풍건조의 경우는 건조시작 10분 경과 후, 진공건조의 경우는 40분 경과 후 $40^{\circ}C$에 도달하였다. 마이크로파 진공건조의 경우 건조 2시간 후 수분함량 0.08 kg water/kg solid까지 감소하였으나, 열풍건조의 경우 건조 시작후 2시간이 경과했는데도 겨우 수분함량 0.70 kg water/kg solid까지만 감소하였다. 마이크로파 진공건조의 경우는 초기 건조속도는 0.06 kg water/kg solid/min이었으며 처음부터 건조속도가 계속 감소하는 감률건조를 보였다. 열풍건조의 경우는 건조 초기 건조속도가 0.0045kg water/kg solid/min으로서 마이크로파 진공건조의 1/10 이하였으며 건조개시 40분까지 항률건조를 보이다가 임계수분함량 0.89 kg water/kg solid 부근부터 감률건조가 시작되었다. 건조시료의 ${\alpha}-amylase$ 활력, diastatic activity 및 protease 활력은 마이크로파 진공건조, 동결건조, 진공건조 및 열풍건조의 순서를 보여 마이크로파 진공건조의 품질보존효과를 알 수 있었다.

• 한국식품과학회지
• /
• 제30권5호
• /
• pp.1107-1113
• /
• 1998

품질이 우수한 효소식품으로의 활용가능성 검토를 위해 현미를 발아시킨 후 마이크로파 진공건조로 건조하고 그 건조특성과 품질특성을 열풍건조, 진공건조, 그리고 동결건조의 경우와 비교해 보았다. 마이크로파 진공건조 1 및 2의 경우 열전달속도가 빨라 건조 개시후 5분 경과후 $60^{\circ}C$에 도달하였고 건조시간 내내 $60{\pm}2^{\circ}C$를 유지하였으나 열풍건조의 경우는 건조개시 60분 경과 후, 진공건조의 경우는 2시간 경과 후에야 $60^{\circ}C$에 도달하였다. 마이크로파 진공건조 1의 경우 건조 3시간 후 수분함량 0.08 kg water/kg solid까지 감소하였으나, 마이크로파 진공건조 2의 경우 총건조시간 2시간만에 수분함량 0.O6 kg water/kg solid까지 감소하였다. 열풍건조의 경우 건조시간 4시간만에 수분함량 0.14 kg water/kg solid까지 감소하였으나 최소한 2시간은 더 건조시켜야 할 것으로 예상되었다. 마이크로파 진공건조 1 및 2의 초기 건조속도는 0.05 kg water/kg solid/min이었으며 처음부터 건조속도가 계속 감소하는 감률건조를 보였다. 열풍건조의 경우는 초기 건조속도가 0.0057 kg water/kg solid/min으로서 마이크로파 진공건조 1 및 2의 1/10 수준이었으며 건조개시 30분까지 항률건조를 보이다가 임계수분함량 0.81 kg water/kg solid 부근부터 감률건조가 시작되었다. 건조시료의 ${\alpha}-amylase$ 활성 및 protease 활성은 마이크로파 진공건조, 동결건조, 진공건조 및 열풍건조의 순서를 보였고, diastatic activity의 경우 동결건조와 마이크로파 진공전조가 거의 대등한 품질보존효과를 보여 주었다. 이로부터 마이크로파 진공건조를 이용하여 건조할 경우 최소한 동결건조와 대등한 품질의 건조제품을 제조할 수 있으리라 예상되었다.

• 한국식품저장유통학회지
• /
• 제22권5호
• /
• pp.708-713
• /
• 2015

고구마 잎을 건조 채소화 하기 위한 기초자료를 제공하기 위해서 열풍건조한 고구마 잎 메탄올 추출물에 함유된 총 탄닌, 총 플라보노이드, 총 폴리페놀 함량을 분석하고, 항산화 효과로 DPPH 라디칼 소거활성, ABTS 라디칼 소거능, 아질산염 소거능 등을 분석 비교 검토하였다. 총 탄닌 함량은 신미 $40^{\circ}C$에서 10.87 mg/g, $70^{\circ}C$에서 7.28 mg/g으로 감소되었고, 총 플라보노이드는 하얀미 $40^{\circ}C$에서 55.37 mg/g, $70^{\circ}C$에서 39.63 mg/g으로 감소되었다. 즉 저온건조가 고온건조보다 이들 물질의 함량이 많았다. DPPH 라디칼소거 활성은 신미와 하얀미 $40^{\circ}C$에서 84.33%와 85.25%로 가장 높았으며, ABTS 라디칼 소거능도 $40^{\circ}C$ 처리구에서 80%가 넘는 높은 값이었다. 아질산염 소거능은 신미와 하얀미가 $40^{\circ}C$에서 76.15%와 73.74%로 가장 높았고 $70^{\circ}C$에서는 낮았다. 품종 간에는 하얀미가 신미보다 페놀성 물질과 항산화 물질이 더 많은 것으로 나타났다. 즉 건조한 고구마 잎의 항산화 효과는 품종간의 차이는 있었으나, $40^{\circ}C$ 시료에서 높고, $70^{\circ}C$ 시료에서 낮았다. 이는 건조온도에 의해 영향을 받는 것으로서 낮은 온도에서 건조하는 것이 유효성분의 감소가 적어 항산화 능력이 높은 결과이었다.

• 한국수산과학회지
• /
• 제48권6호
• /
• pp.839-848
• /
• 2015

This study examined the optimal salting drying method and processing conditions (salt concentration, curing time, dry temperature, and drying time) for preparing salted semi-dried common gray mullet (SSD-CGM) Mugil cephalus based on the moisture content, salinity, and overall acceptance using response surface methodology (RSM). The moisture content, salinity, and overall acceptance of SSD-CGM prepared with different salting methods revealed that dry salting was the optimal salting method for preparing high-quality SSD-CGM. The optimal drying method for preparing high-quality SSD-CGM based on the drying velocity and sensory color was hot air-blast drying. The results of the RSM program indicated that the optimal independent variables ($X_1$, salt concentration; $X_2$, curing time; $X_3$, dry temperature; $X_4$, drying time) based on the dependent variables ($Y_1$, moisture content; $Y_2$, salinity; $Y_3$, overall acceptance) for high-quality SSD-CGM were 5.6% for $X_1$, 2.7 h for $X_2$, $47.0^{\circ}C$ for $X_3$, and 8.5 h for $X_4$ for uncoded values. The predicted values of $Y_1$, $Y_2$, and $Y_3$ for SSD-CGM prepared under optimal conditions were 54.4%, 4.2%, and 6.3, respectively, while the experimental values were $55.2{\pm}1.0%$, $4.1{\pm}0.3%$ and $6.7{\pm}0.8$. The actual and predicted values did not differ.

• 한국식품영양과학회지
• /
• 제35권6호
• /
• pp.780-785
• /
• 2006

무청별 무청의 성분분석과 반응표면 분석법을 이용하여 건조조건에 따른 무청 고유의 색도, 칼슘, 철분, 비타민 등의 성분을 조사하였다 일반성분의 경우 품종이 다른 미농단백무(RL5)를 제외하고는 품종 간에 회분, 단백질, 지방, 칼슘 및 철분함량에 유의적인 차이가 없었고, 건물량으로 환산한 비타민류, 클로로필 함량, 색도에는 품종 간 유의적인 차이가 있었다. 한편 중심합성 실험계획에 따라 건조한 미농단백무 무청의 품질특성을 조사한 결과 수분함량, 클로로필 함량 및 색도차이를 나타내는 ${\Delta}E$ 값은 건조온도와 시간에 따라 유의적인 차이가 있었고, 칼슘, 철분함량은 각각 $31.41{\sim}35.80\;mg,\;0.21{\sim}0.29\;mg$으로 시료 간 유의성이 없었다. 무청의 건조조건을 독립변수로 하고, 시료 간 유의적인 차이를 보였던 종속변수인 수분, 클로로필 및 색도 값의 상관관계를 나타내는 $R^2$값이 0.97 이상으로 높았다. 또 회귀분석한 모델식중 반응표면 분석법으로 도시한 결과 총 클로로필 함량은 독립변수인 건조시간보다는 건조온도의 영향이 더 컸으며 무청의 고유 초록색을 유지하면서도 수분 감소효과를 얻기 위한 최적조건은 약 $70^{\circ}C$에서 $5{\sim}6$시간 정도로 예측할 수 있었다.

• 한국약용작물학회지
• /
• 제25권6호
• /
• pp.397-403
• /
• 2017

Background: This study was aimed at evaluating the growth, yield, and carbohydrate content in the whole Allium hookeri plant with shading treatment in hot summer. Methods and Results: Different shading rate, including 0 (control), 35 or 55%, was employed from the June $21^{st}$ to August $31^{st}$. Daily average air and soil temperature, which were approximately $2.5^{\circ}C$ and $3.8^{\circ}C$ lower, respectively, were observed with both 35% and 55% treatments in July and August, with no significant difference in daily maximum air temperature. Dry weights were high, approximately 40% and 48% for the shoot and 20% and 12% for the root, with the 35% and 55% treatments, respectively, 8 weeks after shading. Division number was increased by 13% and 19.8% with the 35% and 55% treatments, respectively. The mortality rates of 150 plants were 9.1%, 4.0%, and 1.3% with the 0 (control), 35% and 55% treatments, respectively. At 4 weeks after shading, the highest and lowest sucrose levels in both shoot and root were observed with the 35% and 55% treatments, respectively. At 8 weeks after shading, there was no significant difference in the sucrose content in the shoot among the treatments. Conclusions: The highest plant growth rate and yield with the 55% treatment may be related with the decrease in both air and soil temperatures, resulting in reducted leaf respiration and thus compensate net photosynthesis.

• 한국농공학회논문집
• /
• 제64권5호
• /
• pp.9-16
• /
• 2022

Syngas, also known as synthesis gas, synthetic gas, or producer gas, is a combustible gas mixture generated when organic material (biomass) is heated in a gasifier with a limited airflow at a high temperature and elevated pressure. The present research was aimed at modifying the existing LPG engine generator for fully operated syngas. During this study, the designed gasifier-powered woodchip biomass was used for syngas production to generate power. A 6.0 kW LPG engine generator was modified and tested for operation on syngas. In the experiments, syngas and LPG fuels were tested as test fuels. For syngas production, 3 kg of dry woodchips were fed and burnt into the designed downdraft gasifier. The gasifier was connected to a blower coupled with a slider to help the air supply and control the ignition. The convection cooling system was connected to the syngas flow pipe for cooling the hot produce gas and filtering the impurities. For engine modification, a customized T-shaped flexible air/fuel mixture control device was designed for adjusting the correct stoichiometric air-fuel ratio ranging between 1:1.1 and 1.3 to match the combustion needs of the engine. The composition of produced syngas was analyzed using a gas analyzer and its composition was; 13~15 %, 10.2~13 %, 4.1~4.5 %, and 11.9~14.6 % for CO, H₂, CH₄, and CO₂ respectively with a heating value range of 4.12~5.01 MJ/Nm³. The maximum peak power output generated from syngas and LPG was recorded using a clamp-on power meter and found to be 3,689 watts and 5,001 watts, respectively. The results found from the experiment show that the LPG engine generator operated on syngas can be adopted with a de-ration rate of 73.78 % compared to its regular operating fuel.