• Journal of Korea Foundry Society
• /
• v.20 no.2
• /
• pp.110-115
• /
• 2000

In this study, the powders of Mg-3wt%Al-1wt%Zn-1wt%MM alloy were produced under vacuum condition by the inert gas atomization and the rapidly solidified powders were consolidated by the vacuum hot extrusion. Then the structural change of powders during extrusion was investigated. The effects of misch metal addition to AZ31 on mechanical properties of extruded bars were also examined. During extrusion of the rapidly solidified powders, their dendrite structure was broken into fragments and remained as grains of 2 ${\mu}m$ size in extruded bar. The Mg-Al-Ce intermetallic compounds formed in the interdendritic regions of powders were broken finely, too. The yield stress, tensile strength and ductility obtained in as-extruded Mg-3wt%Al-1wt%Zn-1wt%MM alloy were ${\sigma}_{0.2}=325$ MPa, ${\sigma}_{T.S.}=417$ MPa and ${\varepsilon}=16.8%$. All of these improvements on mechanical properties result from the refined micostructure and second-phase dispersions.

• Korean Journal of Materials Research
• /
• v.13 no.6
• /
• pp.374-380
• /
• 2003

The effect of forging parameters, including different forging stock, strain rate and strain, on the mechanical properties of hot-forged Al 6061-T6 was investigated. The forging was conducted using either hydraulic press, crank press or hammer press, respectively, at a forging temperature of $400^{\circ}C$. When using an extruded bar as a forging stock, the tensile strength was lower for the specimens prepared by hammer forging than those by crank press forging. It was found that the coarsening of recrystallized grain was responsible for the decrease in tensile strength with hammer forging. Systematic studies on the effects of strain and strain rate on the tensile properties of hot-forged Al 6061-T6 products using extruded bar as a forging stock further suggested that the coarsening of recrystallized grains and$ Mg_2$Si precipitates complexed the observed trends in the tensile behavior. In case of hot forging with continuous cast bar as a forging stock, on the other hand, the mechanical properties of the specimen were largely improved with hammer press compared to those with crank press, which appeared to be due to the homogenization of microstructure.

• Transactions of Materials Processing
• /
• v.15 no.2 s.83
• /
• pp.143-147
• /
• 2006

Effect of processing condition on the hot extrusion of Al-Zn-Mg-Sc alloy was investigated. For this purpose, hot compression test and FE-simulation were conducted via Thermecmaster-Z and DEFORM-3D, respectively. The microstructure evolution during hot extrusion and post heat-treatment was investigated and deformation mechanisms were analyzed by constructing processing map. FE-simulation results show that the temperature difference between container and billet has considerable influence on the final shape of extruded T-shape bar. The relation between applied load and processing time was predicted by the FE-analysis as well as punch speed vs. stroke chart.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.202-205
• /
• 2005

Effect of processing condition on the hot extrusion of Al-Zn-Mg-Sc alloy was investigated. For this purpose, hot compression test and FE-simulation were conducted via Thermecmasteer-Z and DEFORM-3D, respectively. The microstructure evolution during hot extrusion and post heat-treatment was investigated and deformation mechanisms were analyzed by constructing processing map. FE-simulation results show that the temperature difference between container and billet has considerable influence on the final shape of extruded T-shape bar. The relation between applied load and processing time was predicted by the FE-analysis as well as punch speed vs. stroke chart.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1993.11a
• /
• pp.28-28
• /
• 1993

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1993.11a
• /
• pp.29-29
• /
• 1993

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.281-284
• /
• 2007

The effect of Ca addition on the microstructure evolution and deformation behavior of AZ31 magnesium alloy produced by hot extrusion was investigated. For this purpose, Ca was added into AZ31 melts to the level of 0.7 and 2.0 wt.% Ca. Then, AZ31 base alloy and Ca modified AZ31 alloys were extruded at $383^{\circ}C$. Ca added alloys showed finer grain size and increased hardness value rather than AZ31 base alloy. After isothermal hot compression, the shape of tested specimen exhibited a noticeable anisotropy due to the crystallographic texture effect. The ratio of major and minor axes of ovality was not directly related to test condition and Ca amount. Flow stress level increases with the increase of Ca addition at temperature below $300^{\circ}C$ because of fine microstructure. However, at high temperature and low strain rate region ($400^{\circ}C$ and $10^{-3}s^{-1}$), reverse tendency was observed since main deformation mechanism changes from dislocation slip to grain boundary sliding or diffusional process at high temperature.

• Journal of Korea Foundry Society
• /
• v.17 no.4
• /
• pp.365-370
• /
• 1997

The effects of changes in microstructure of Si phase on the thermal expansion coefficients(CTEs) and tensile properties of the hypereutectic Al-Si foundry alloy(A390) were investigated experimentally. Specimens were prepared by various fabrication processes, such as a permanent mold casting, a squeeze casting and a spray casting process, and subsequently hot-extruded. CTEs of the spray-cast specimen were found to be about 10% lower than those of the permanent mold-cast specimen, and the CTEs of the hypereutectic Al-Si alloy(A390) were changed proportionally with the size of Si phase. Ultimate tensile strength of the spray-cast and hot-extruded specimen was dramatically improved about 100% with improved elongation, compared to that of permanent mold-cast specimen. These improvements are mainly attributed to the reduction in size and aspect ratio of the brittle Si phase, and the elimination of the microvoids/porosities formed during casting.

• Journal of Korea Foundry Society
• /
• v.15 no.5
• /
• pp.459-468
• /
• 1995

For high performance aerospace structures, the properties of highest priority are low density, high strength, and high stiffness(modulus of elasticity). Addition of beryllium decrease the density of the aluminum alloy and increase the strength and the stiffness of the alloy. However it is very difficult to produce the Al-Be alloy having useful engineering properties by conventional ingot casting, because of the extremely limited solid solubility of beryllium in aluminum. So, rapid solidification processing is necessary to obtain extended solid solubility. In this study, rapidly solidified Al-6 at% Be alloy were prepared by twin roll melt spinning process and single roll melt spinning process. Twin roll melt spun ribbons were extruded at $450^{\circ}C$ with reduction in area of 25 : 1 after vacuum hot pressing at $550^{\circ}C and 375^{\circ}C$. The microstructure of melt spun ribbon exhibited a refined cellular microstructure with dispersed Be particles. As advance velocity of liquid/solid interface increase, the morphology of Be particle vary from rod-like type to spherical type and the crystal structure of Be particle from HCP to BCC. These microstructural characteristics of rapidly solidified Al-6at.%Be alloy were described on the basis of metastable phase diagram proposed by Perepezko and Boettinger. The extruded ribbon consisted of recrystallized grains dispersed with Be particles and exhibited improved tensile property compared with that of extruded ingot.

• Korean Journal of Materials Research
• /
• v.31 no.12
• /
• pp.672-676
• /
• 2021

In this paper, the effect of Ni (0, 0.5 and 1.0 wt%) additions on the microstructure, mechanical properties and electrical conductivity of cast and extruded Al-MM-Sb alloy is studied using field emission scanning electron microscopy, and a universal tensile testing machine. Molten aluminum alloy is maintained at 750 ℃ and then poured into a mold at 200 ℃. Aluminum alloys are hot-extruded into a rod that is 12 mm in diameter with a reduction ratio of 39:1 at 550 ℃. The addition of Ni results in the formation of Al₁₁RE₃, AlSb and Al3Ni intermetallic compounds; the area fraction of these intermetallic compounds increases with increasing Ni contents. As the amount of Ni increases, the average grain sizes of the extruded Al alloy decrease to 1359, 536, and 153 ㎛, and the high-angle grain boundary fractions increase to 8, 20, and 34 %. As the Ni content increases from 0 to 1.0 wt%, the electrical conductivity is not significantly different, with values from 57.4 to 57.1 % IACS.